Category : Forging Equipment

Sub-Category : Hammer Drop Forging

Total Machines Found : 7

Select | Machine Details
 
  1
IDMA29301
MakeCeco
Model
YOM
ConditionVery good condition
PhotoSee Photo
Rated size: 1500 Kg,
Cylinder bore: 7-3/4 mm,
Inlet: 2 mm,
Exhaust: 2-1/2 mm,
Overrall above floor line: 183 mm,
Floor space: 39 x 80-1/2 mm,
Ram stroke: 42 mm,
Distance from top of anvil cap to bottom of guide: Std guide: 13-9/16, Ext. guide: 9-9/16 mm,
Between guides: 18 mm,
Ram front to back: 16 mm,
Anvil cap front to back: 23 mm,
Closed die height :
Max: 15 mm,
Min: 8 mm,
Min die bearing area: 87 Sq.cm,
Minimum striking area: 20 mm,
Air consumption: 220 M3 per min,
Steam: 445 Kg per Hr.
 
  2
IDMA26983
MakeBeche
ModelRF4
YOM1974
ConditionGood Condition
PhotoSee Photo
Capacity : 2150 kg,
Max. stroke ; 1850 mm,
4000 Mkg,
wheel diameter : 1170 mm,
Speed of wheel : 2,7 m/sec,
Hammer belt : 18 x 700 mm,
Stroke per min : 34,
Motor : 50 kW,
Total weight : 64 tons,
Max. height over floor : 5500 mm,
Overall size : 6,4 sq.m.
 
  3
IDMA24355
MakeBeche
ModelKGL2
YOM
ConditionVery good condition
PhotoSee Photo
Percussive energy 2000 mkg.
Stroke of tup max. 600 mm,
Strokes (full blow) max. 120 min^-1,
Assumed number of strokes (Full blow),
average 30 min^-1,
Ram (front to back)440 mm,
Height of dies without dovetails, min.250 mm,
Daylight between the guides 560 mm,
Height of machine above floor 3200 mm,
Normal working height 800 mm,
Total weight 27,2 t,
Air consumption in aspirate air per full blow (cold
air) 0,24 m3
Air consumption in aspirate air per full blow
(hot air 220)0,14 m3
Air consumption in aspirate air per minute (cold
air, average number of strokes)7,2 m3
Air consumption in aspirate air per minute
(hot air 220) 4,2 m3,
Necessary Driving power for the compressor,
approx. - (cold air, average number of strokes) 41.19 kW,
Necessary Driving power for the compressor approx. - (hot air 220)24,27 kw.
 
  4
IDMA24342
MakeBeche
ModelKGL2000
YOM
ConditionGood Condition
PhotoSee Photo
Capacity : 2000 kg.m,
Stroke of tup : 600 mm,
Max stroking rate : 85 str / min,
Average admissible stroking rate : 30 str./min,
Width between guideways : 560 mm,
Depth of tup : 440 mm,
Min height of the die without tail : 250 mm,
Height above the floor : 3300 mm,
Height of working station : 800 mm,
Total Weight of hammer : 20 T.
 
  5
IDMA19011
MakeLasco
ModelKH160
YOM1968
ConditionGood Condition
PhotoSee Photo
Percussive energy 1600 mkg,
Mode of operation oil-hydraulic,
Driving power 27 kW,
Total weight 34 t,
Heigth of machine above floor 5000 mm,
Ram weight 1600 kg,
Ram (front to back) 550 mm,
Die height 160 mm,
Heigth of fall 1000 mm .
 
  6
IDMA9521
MakeBeche
Model
YOM
Condition
PhotoSee Photo
falling part weight 500 kg
 
  7
IDMA6581
MakeBeche
ModelDG6
YOM
Condition
PhotoSee Photo
6000 mkg, strokes at max stroke 14mm, total stroke of both rams 900mm, 60SPM, total weight 30t, height of machine above floor 3750mm, ram(front to back) 1060mm, die height 300mm
top