Category : Forging Equipment

Sub-Category : Hot Forging Line

Total Machines Found : 80

Select | Machine Details
 
  1
IDMA34677
MakeAjax
Model
YOM1988
ConditionGood Condition
PhotoSee Photo
Capacity : 2500ton
Slide stroke : 350mm
SPM : 50
Shut height : 1000mm
Slide area : 1320mm X 1240mm
Bolster area : 1380mm X 1520mm
Main motor : 112kw
Machine weight : 150ton

Ho Sung 300ton Trimming press
Induction heater
 
  2
IDMI7748
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
MFG for all Hammer & Trimming Press is 2006 & Induction heater is 2013
2Ton Rattan Belt Drop Hammer with extra tub for sale with 300 Ton Amrit Trimming Press with electrical motor & panel , Oil Fired Furnace,250 Kw Inductotherm Induction Heater with 3 coils with Distilled water re-circulation system
Coil sizes
40
56
80
 
  3
IDMA34647
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
Hydraulic Forging Press- 1500 tons with 1600 mm Ring Rolling machine currently on site on foundation in working, but not under production from Oct 2020, complete plant for manufacturing swing bearing turn table.
Horizontal Saws
Manufactured by Delta (Korea) new in 2006 ~ 2011
SFA series
Model: SFA – 450
Quantity: 5ea
Operation method: NC control system
Cutting capacity
Round, single: 450mm
Square, single: 410mm x 450mm
Round, multiple: 350mm x 200mm
Saw blade
Speed(60Hz): 24~90m/min
Speed(50Hz): 24~90m/min
Size: 4,880 x 41 x 1.3mm
Tension: Hydraulic (30,000psi, factory set)
Feed
Mode: Hydraulic
Length: 0~9,999mm
Electric motors
Band drive: 7.5HP(5.5kW)
Hydraulic system: 2HP(1.5kW)
Coolant pump: 1/8HP(0.1kW)
Tank capacity
Hydraulic: 60L
Cutting fluid: 80L
Machine weight: 2,700kg
Floor space(WxLxH): 2,400 x 1,900 x 1,960mm
Also, there are 6 units of refurbished band saws available.
There are also 2 units of refurbished facing lathes for cutting process.

Rotary type Heating Fuanace
Manufactured by Shinhan Furnace Eng (Korea) new in 1992, 1996
Fuel: B-C oil, Diesel
P.C.D.: 4,890mm
2 Sets

Hydraulic forging press 1,500ton
Manufactured by Hyundai Precision & Ind (Korea) new in 1992
Max pressure force: 1,500tons
Stroke: 1,100mm
Daylight: 2,110mm
Slide surface(left to right X front to rear): 1,500 X 1,200mm
Bolster surface(left to right X front to rear): 2,300mm X 1,200mm
Action speed:
Descending 250mm/SEL
Pressurization: 1,500ton – 39mm/SEL
Ascending: 1,000ton – 55mm/SEL
Lifting capacity: 250mm/SEL
200tons
Moving bolster:
Carrying capacity: 15ton
Moving stroke: 2,100mm(1,100mm)
Diameter of cylinder: D140mm
Punch change device
Moving stroke: 1,600mm(800mm)
Diameter of cylinder: D80mm
Knock-out device
Capacity: 10ton
Diameter of cylinder:
Pump
Main pump
Type: A7V500LV5
Pressure: Max 350kg/cm2
Volume of oil: 2,200L/min
Sub pump
Type: A10 VSO 100 DRF
Pressure: 210kg/cm2
Volume of oil: 110L/min
Cooling pump
Type: NLG 25
Pressure: 6kg/cm2
Volume of oil: 25m3/hr
Motor
Main motor
Output: 175kW x 6P x 4 sets full closure type
Power source: AC330V x 60Hz
Aux motor
Output: 37kW x 4P full closure type
Power source: AC220V x 60Hz
Oil tank
Main tank: 7,000L
Sub tank: 2,500L
Heater
Type: WC5 (Woo Chang)
Capacity: 5kW x 3 sets
Press precision level: JIS 1st grade
Operation control system
Operation type: Push button type
Control type: PLC control
Operation mode: Off, Inch, Single, Continuous

Auxiliary devices
Slide position control
Slide speed control
Pressurization capacity control device
Photo Electric Safety Device
Hydraulic peripheral device
Electric control device
Lubrication device
Portable push button stand
Slide high limit loching device

Ring rolling mill
Manufactured by Mitsubishi, Japan, new in 1992
Model: MRS1600
Machining capacity: Max 400kg
Product diameter: Max 1,600mm (1,700mm)
Product height: 50 ~ 150mm (210mm)
Material size: Max 170mm (250mm)
Material I.D.: Min 100mm
Material OD: Min 250mm
Rolling force (horizontal) Max 80ton, vertical Max 80ton
4 roll pressure (from each side): Max 10ton
Roll specifications: This machine is using various sizes of rolls.
Main roll
O.D.: 800mm
Height: 410mm
RPM: 33.719
Speed: 1.414 m/sec
Motor: AC160kW
Reduction ratio: 1/35.1
Edge roll
Taper angle: 45 degree
O.D.: 45~450
Length: 588mm
RPM: 63.5~256
Motor:: DC 220kW x 1200rpm
Reduction ratio: 1/5.67
Middle roll
O.D. x Length: 110mm Dia x 590mm
80mm Dia
150mm Dia
Four roll
O.D.: 200mm Dia
Length: 112.5mm
Standard roller
O.D.: 150mm Dia
Actuator
Main table cylinder
Size: 250B x 180R x 507mm
Pressure(based on 165kg/cm2): ax 80ton
Stroke: 500mm
Speed
Forward loaded: 0 ~ 5mm/sec
Forward unloaded: 80mm/sec
Backward unloaded: 80mm/sec
Edge roll stand cylinder
Size: 150B x 71R x 2015mm
Drawing force(based on pressure 190kg/cm2): Max 50ton
Stroke: 2000mm
Forward loaded: 0 ~ 50mm/sec
Forward unloaded: 150mm/sec
Backward unloaded: 150mm/sec
Middle roll cylinder
Size: 80B x 45R x 665mm
Pushing force (based on pressure 160kg/cm2): 10ton
Stroke: 650mm
Four roll cylinder
Size: 100B x 56R x 300mm
Pushing force (based on 140kg/cm2): 10ton
Stroke: 295mm
Speed: 80 m/sec
Standard roller cylinder
Size: 40B x 22.4R x 520mm
Capacity (based on 20kg/cm2): 173kg
Stroke: 510mm
Speed: Forward 150 mm/sec
Speed backward: 150mm/sec
Balance cylinder
Size: 140B x 71R x 340mm
Stroke: 320mm
Speed(ascent): 25mm/sec
Hydraulic motor for four stopper
RPM (for both forward and backward): 120
Speed of stopper moving: 2mm/sec
Stopper moving stroke: 300mm
Type: Obit motor
H—200DA2XJ
Sumitomo Eton
Hydraulic Drive Pump
Variable volume piston pump: 105L/min x 210kg/cm2
320L/min x 70kg/cm2)
Motor
For main roll motor: 160kW, 6P, 3300V, 60Hz
For edge roll motor: DC 220kW, 440V
Hydraulic pump drive: 55kW, 6P, 440V, 60Hz (2ea)
For aux pump drive: 30kW, 6P, 440V, 60Hz

Quenching Elevator System
Manufactured by Kukdong Shoei Vans (Korea), new in 1992
Specifications available upon request

Pot type high temperature Tempering Furnace
Manufactured by Shoei Korea, new in 2006
Electric type
Temp range 680 ~ 700 degree
Specifications available upon request
Quantity: 4ea
Hoist 3ea

Robots with Placing Machine
New in 1992

Various spares and accessories
 
  4
IDMA34600
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) 700 ton National Forging Press:
Capacity ........ 700 Ton
Stroke .......... 8”
Shut Height ..... 22”
Stroke .......... 8”
Speed ........... 90 spm
Bed Size ........ 24" LR x 39" FB
Ram Size ........ 21" x 22"
Windows ......... 14.5"
Floor Standing .. Yes
Knock outs ...... Bottom
Air Clutch ...... Yes
Air Brake ....... Yes
2) 150 KW Ajax Tocco Induction Heater
 
  5
IDMA34592
MakeTMP Voronezh Russia
Model
YOM
ConditionGood Condition
PhotoSee Photo
Voronezh 1600ton hot forging press & Hwail 160ton Trimming press
 
  6
IDMA34470
MakeMassey
Model
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
1) Used MASSEY 1300t Mechanical Closed Die Forging Press
YOM:1978
Max tonnage……………………………………………………………….1300t
Stroke…………………………………………………………………………. 250mm
Wedge Adj…………………………………………………………………….…10mm
Strokes/Min……………………………………………………………………..90spm
Bed L to R………………………………………………………………………..785mm
Bed F to B………………………………………………………………………..840mm
Electrics……………………………………………………..400/440v-3ph-50Hz
Dimensions………………………………………..…….3330 x 3845 x 4725mm
Weight……………………………………………………………………………….75t
2) used MASSEY 250t Wide Ram Trimming Press
YOM:1986
Max tonnage…………………………………………………………………250t
Stroke……………………………………………………………………………250mm
Slide adj…………………………………………………………………………..10mm
Strokes/min……………………………………………………………………..45spm
Bed area………………………………………………………………1270 x 915mm
Ram area……………………………………………………………..1250 x 900mm
Main drive………………………………………………………………………..22Kw
Electrics……………………………………………………..400/440v-3ph-50Hz
Weight………………………………………………………………………………24t
 
  7
IDMA34460
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
Forging Press
Make:Smeral
Model:LKM-1600
Capacity:1600 tons
Stroke:280 mm
Shut Height:760 mm
SPM:80
Bed:1248 x 1140 mm
Ram:920 x 920 mm
Bottom Knockout:20 tons
Bottom Knockout Stroke:50 mm


Trimming Press
Make: Kurimoto
Model:SGP1-150
Capacity:150 ton
Stroke:180 mm
SPM:45
Die Height:400 mm
Adjust:110 mm
Bolster:800 x 800 mm
Slide:650 x 700 mm
Machine Type:Heater
Make:Uchino
Capacity:300 Kw
YOM:2007 December
Power:3 Ψ 200V (Y) + 3 Ψ 200V (Δ)
Coil:2 with motor
Coil:75΅H (Ψ50,Ψ60)
Condenser:65uF, 2P x 2S
CT:3000A/5A/10V
fL:2400Hz
fH:4000Hz
Stopping Time:13΅sec
Coil with heater of 50 and 60 mm dia and one spare coil of 60 mm dia with heater.
 
  8
IDMA34184
MakeHosung Korea
ModelHFP-450
YOM2000
ConditionGood Condition
PhotoSee Photo  |  See Video
Press Hot Forging:
Capacity : 450 ton
Stroke : 160 mm
S.P.M : 110
Die Height : 477 mm
Slide adjustment : 8 mm
Slide aera : 615 x 65
Induction Heater : 250kw(2003)
Trimming Press : 80 ton
 
  9
IDMA34170
MakeManyo,Japan
ModelLP2500-380S
YOM2001
ConditionGood Condition
PhotoSee Photo
Lever type
Capacity: 25MN
stroke: 380 mm
spm: 40
Shut height: 1200 mm
Die height: 630 mm
Slide adjust: 20 mm
Die Pitch: 350 mm
Die stages 4-stages
Bed area: 2580 x 1260 x 280 mm
Wear Plate area: 1860 x 900 x 250 mm
Distance between Column: 1940 mm
Upper K.O. 200KN x 50 mm 1 – 4 stages
Lower K.O. 900KN x 100 mm 150 / 300 / 300 / 150 KN
Main Motor 200kw x AC3300V High Voltage
Hydraulic motor 45kw x 6P x 220V
Adjust moto:r 11kw x 6P x 220V
Lub. pump 0.4kw x 4P x 220V x 3 units
0.1kw x 4P x 220V x 2 units
2. Transfer Unit
Feed x Clamp x Lift 350 x 160 x 150 mm
Control AC Servo motor
7kw x 5units , 1kw x1unit
3. Trimming press
300ton trimming press Bed size : 1500 x 900 MTP300-300S
4. Induction Heater
Spec : 1400kw , Mitsubishi
 
  10
IDMA34169
MakeJewoo Press
ModelJFP1350
YOM2007
ConditionGood Condition
PhotoSee Photo
Capacity 1350 ton
stroke 240 mm
spm 88
Die height 683 mm
Slide adjust 6 mm
Slide area 880 x 920 mm
Bolster area 920 x 960 mm
Induction Heater
spec 580 V x 3P x 600kw
Trimming Press
spec 160ton C-type press
 
  11
IDMA34021
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Machine Type: Forging Press
Make: Smeral
Model:LKM-1600
Capacity: 1600 tons
Stroke:280 mm
Shut Height:760 mm
SPM:80
Bed:1248 x 1140 mm
Ram:920 x 920 mm
Bottom Knockout:20 tons
Bottom Knockout Stroke:50 mm

Machine Type: Trimming Press
Make: Kurimoto
Model:SGP1-150
Capacity: 150 ton
Stroke: 180 mm
SPM: 45
Die Height:400 mm
Adjust: 110 mm
Bolster:800 x 800 mm
Slide:650 x 700 mm
With heater
 
  12
IDMA33874
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1 Pieces Lasco Kh50 forging hammer
1 Pieces Elotherm 500 kva induction heater
1 Pieces Lasco Kh50 hydraulic unit
8 Pieces induction inductor
and viscodamper spring
 
  13
IDMA33769
MakeNational
ModelMaxipress
YOM1970s
ConditionGood Condition
PhotoSee Photo
Complete line
Capacity: 4000 ton,
Strokes per minute:46
Stroke:15”
Shut Height - Low:38-1/4”
Shut Height - High: 39”
Shaft dia. at eccentric: 41-1/4”
Dia. of tie rods:15”
Die Seat (F-B):63”
Die Seat (R-L):61”
Ram Face (F-B): 52”
Ram Face (L-R):56”
Width between columns:63” (LR)
Motor (hp):250HP - 900RPM
Floor space (RL):16’7”
Floor space (FB):14’2”
Height above floor:18’5”
Net weight (approx.):600,000bs
COMPLETE WITH:
Ram counterbalance cylinder
Hydraulic wedge
Steel overarm ram
Tonnage indicator
Trabon recirculated pressure oil lubrication
Operators push button controls
Lower and upper die knockouts
Air clutch
Complete with:
4000ton National Hot Forging Press
1000ton Clearing Coining Press
2000ton Ajax Forging (pre-form) Press
400ton Bliss Trim Press
1000 kW AIH Induction Heater
AWS Hasenclever Reducer Roll
Hasenclever AWS 280 Reducer Roll
Hasenclever AWS 280 Manipulator
AIH Heater, Bin Dumper, De-scramble table,
with Vee-flight & Pinch wheel track
AIH Heater Pinch Wheel Track
AIH Heater Cooling Skid
AIH Heater Pinch Wheel
AIH Power Supply
AIH Heater Controls
ISW Micro-alloy conveyor (trim or coin output)
Many, many accessories, parts, tooling, etc.

Note: Was setup for front steering spindles. Part weight was 15lbs, Material 4340, Area approx. 288sqare Inches.
 
  14
IDMA33672
MakeHosung Korea
ModelHFP750
YOM2006
ConditionGood Condition
PhotoSee Photo
Capacity : 750 Ton
Slide stroke : 180 mm
Speed : 100 SPM
Die height : 580 mm
Adjustment : 8 mm
Slide size : 720 x 780 mm
Upper Knockout stroke : 10 mm
Lower Knockout stroke : 40 mm
Main motor : 55 kW
-Induction heater
-Trimming press
 
  15
IDMA33542
MakeNittan ,Japan
ModelMHFP-2800-LW
YOM2003
ConditionGood Condition
PhotoSee Photo
Type:Straight Side Eccentric Forging Press
Capacity:2800 ton
Stroke:356 mm
Shut Height:1008 mm
Adjust:18 mm
Idling Strokes:60
Effective work strokes:20
Ram:1120 x 1370 mm
Table:1040 x 1405 mm
Upper Ejector in Ram
Type:Mechanical
Capacity:10 tons
Stroke:35 mm
Ejector in Table
Type:Hydraulic
Capacity:25 tons
Stroke:70 mm
Main Motor:150 Kw, 480V, 6P
Complete with trimming press and heater etc.
 
  16
IDMA33489
MakeTMP Voronezh Russia
ModelKB8546
YOM1988
ConditionGood Condition
PhotoSee Photo  |  See Video
Double crown type
Capacity: 4000 ton
Stroke: 400mm
SPM: 50
Shut height: 1000mm
Slide adjustment: 10mm
Table(left-right x front-rear): 1570mm x 1620mm
Slide(left-right x front-rear): 1420mm x 1420mm
Top ejector max.stroke: 65mm
Bottom ejector max.stroke: 65mm
Main motor: 160kW
Weight: 363ton
Press size: 6228 x 5515 x 7790mm(H)
Induction heater(=heat treatment furnace)

1) Heat treatment furnace (1988, Uchino: Japanese make)

2) Spare coil 2units of heat treatment furnace
 
  17
IDMA33464
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Price:
1) 1600/200 Forging Hydraulic press: USD 42,5000 EXW
2) 1 Ton Forging manipulator: USD 49,500 EXW
3) 1 ton loader/unloader: USD 38,000 EXW

1600/2000 Ton Forging Hydraulic Press Unit
1600/2000 ton forging hydraulic press unit is consist of 1600/2000 ton forging hydraulic
press, 2 ton forging manipulator, 2 ton loader/unloader.
1. 1600/2000 Ton Forging Hydraulic Press
1、Main functions and features
1.1 Main functions:
1.1 This press is mainly used for traditional free forging process(blanking, upsetting,
stretching, bending, twisting, cutting, shifting, etc).
1.2 Main features:
1.2.5 The machine pressing down(slider stroke) equipped with position detection
and control.
1.2.8 The press equipped with one piece of upper anvil bolster, one set of upper
anvil base, one set of horizontal anvil shifting device(three anvil stations), flat anvil(one
pair), one piece of down V-shaped anvil, one set of swage die, down anvil base(three
pieces), one set of rotary upsetting table.
2、Working condition
2.2 Cooling method: oil cooler, provide by buyer(seller design and guide
installation).
3、Specifications
3.1 Max. pressure during flattening(main slider tonnage) 1600T(forging)
2000T(upsetting)
3.2 The distance between the forging die mounting surface(Daylight)
3100mm(moveable working table upper surface to slider down surface)
3.3 Main stroke of slider 1500mm
3.4 Center distance between columns 2400Χ1200mm
Column diameter ≥350mm
3.5 Forging eccentricity 150Χ100mm

3.6 Moveable working table 3 working stations
3.7.1 Size of moveable working table 4000Χ1500mm
3.7.2 Stroke of moveable working table 2000mm (F.B.)
3.7.3 Speed of moveable working table 250mm/s(adjustable)
3.7.4 Loading capacity of moveable working table 20Ton
3.8 Height of the table molding die upper surface from the ground -100mm
3.9 Main slider speed approaching speed 250mm/s
pressing speed 60mm/s(1400T)
returning speed 250mm/s
Fast forging times 45times/m(working stroke≤30mm, tonnage 1000T)
3.10 Liquid working pressure 24Mpa(1600T)
21Mpa(1400T)
19Mpa(1250T)
16Mpa(1000T)
3.11 Working cylinder adopts plunger cylinder 1 set 1600T
(plunger diameter 920mm)
3.12 Returning cylinder adopts plunger cylinder 2 sets 2Χ100T
(plunger diameter 200mm)
3.13 Main motor power 160Χ4=640kW
Accumulator 5Χ100L=500L
Total power 640+55=695KW
3.14 Height above floor 8500mm
3.15 Working voltage AC 380V, +5/-10%, 50Hz
9、Configuration
9.1 Main oil pump A2FO160 4 sets China REXROTH
A2FO250 4 sets China REXROTH
9.2 Fill valve China product
9.3 Magnetic exchange valve German REXROTH

9.4 Integrated cartridge China product
9.5 Cylinder seals China product
9.6 Motor 160KW 4 sets China product
9.7 PLC Siemens
9.8 Touch screen Taiwan,China
9.9 Pressure sensor German IFM
9.10 Displacement sensor Kang Yu
9.11 Other electrical components Chint
9.12 Other hydraulic accessories Domestic quality products
9.13 Fast forging valve China product Proportional valve ATOS
9.14 Accumulator Fenghua or Danyang
9.15 Circulating pump unit China product
9.16 Oil filter Wenzhou
9.17 Oil cooler purchased by buyer in Wuxi,China
10、Range of Supply
10.1 Forging press host 1 set
10.2 Hydraulic power system(including 1 set of filter pump motor group) 1 set
10.3 Starter cabinet 1 set
10.4 Electrical control cabinet 1 set
10.5 Operating table 1 set
10.6 All hydraulic pipeline and accessories 1 set
10.7 Full set of electrical cables in the equipment 1 set
10.8 Wearing parts 1 set
10.9 Upper anvil bolster 1 set
10.10 Upper anvil base 1 set
10.11 Horizontal anvil shifting device(three anvil stations) 1 set
10.12 Flat anvil 1 pair
10.13 Down V-shaped anvil 1 piece

10.14 Down anvil base 3 pieces
10.15 Swage die 1 set
10.16 Filtration circulation system and pipeline 1 set
10.17 Rotary upsetting table 1 set
2. 1 Ton Forging Manipulator
2、Working condition
2.1 Operation temperature: 0~40°C
2.2 Cooling type: water cooling
2.3 Power supply: three-phase four-wire system 380V
2.4 The fluctuation of voltage: 380V±10%
2.5 Power: ~25kW
2.6 Working medium for hydraulic system: anti-wear hydraulic oil YB-N46
3、Technical Specification
3.1 Carrying capacity 1 ton
3.2 Clamping moment 2T.M
3.3 Clamping diameter of bar Ф100/Ф450mm (Min./Max.)
3.4 Height of clamp frame center 600/1100mm (Min./Max. from rail surface)
3.5 Extension of clamp beam 1200mm
3.6 Gauge 2000mm
3.7 Carriage traveling speed 0~25m/min
3.8 Parallel rise and down speed 3m/min
3.9 Jaw clamping time 5s
3.10 Clamp frame tilt angle Up-tilt 7° Down-tilt 10° to floor
3.11 Jaw rotation angle ±360°
3.12 Jaw rotation speed 1~12 r/min
3.13 Max. diameter of jaw rotation 890mm
3.14 Pressure of hydraulic system 16MPa
3.15 Total power 25kW

3.16 Two operation modes: manual and linkage with forging hydraulic press
3. 1 Ton Loader/unloader
2、Technical Specification
2.1 Carrying capacity 1 ton
2.2 Clamping diameter of cake ring parts
2.3 Height of clamp frame center 1000mm
2.4 Clamp head control height 0~1.6m
2.5 Extension of clamp beam 2000mm(guaranteed to hold forgings in the furnace)
2.6 Gauge 4000mm
2.7 Distance from rail center to carriage end face ≤350mm
2.8 Carriage traveling speed 54m/min
2.9 Table frame rotation angle ±360°
2.10 Table frame rotation speed 3.2 r/min
2.11 Trolley speed 24m/min
2.12 Jaw rotation angle ±360°
2.13 Oil pressure 12MPa
2.14 Carriage length 4.7m
2.15 Total motor power 17.2KW
2.16 Total weight 14T
2.17 Power source sliding touch line type (or trench towline type)
2.18 Overall dimensions 4.7Χ2.3Χ2.3m (LΧWΧH)
 
  18
IDMA33381
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Type:Forging Press
Make: Smeral
Capacity:1000 ton
Model: LZK 1000
Stroke:220 mm
SPM :100
Shut Height:620 mm
Adjust;10 mm
Table:1000 x 950 mm
Ram:840 x 750 mm
Top Knockout:35 mm
Bottom Knockout:50 mm
Main Motor:55 Kw


Type:Trimming Press
Make:Suzuki
Model: SGP-150N
Capacity:150 ton
Stroke:180 mm
SPM:45
Die Height:400 mm
Adjust:110 mm
Bolster:800 x 800 mm
Ram:650 x 700 mm
Die Cushion:10 ton
Cushion Stroke:90 mm
 
  19
IDMA33043
MakeSumitomo,Japan
ModelTFPX2000
YOMNew 2006
ConditionGood Condition
PhotoSee Photo  |  See Video
Make: Sumitomo
Model: TFPX-2000
Capacity: 2000 to,
Stroke 350 mm (13.78")
Strokes per min 75
Shut height 850 mm (33.47")
Slide Adj. 7 mm (.27")
Ram size 1200 mm LR X 1300 mm FB
Bed size 1320 mm LR X 1300 mm FB
Year 2006
4 stage transfer system
Slide knockout
Bottom knockout
Billet Cold Saw
1300 °C Induction Heating line
Induction line control
which includes 1600 Kw Induction Heater, Complete Transfer Beam, Nishimax Saw and new spare parts
 
  20
IDMA33023
MakeEUMUCO
ModelSP1000
YOM1997
ConditionGood Condition
PhotoSee Photo
34" L-R X 36" F-B BOLSTER SIZE
AIR CLUTCH
ELAU PRESS CONTROL AUTOMATIC OPERATION
AJAX TOCCO TYPE BTH 1000 4022127 INDUCTION COIL
SERIAL NO 22224623
1996 AEG ELOTHERM ELOMAT INDUCTION HEATER
1,100-KVA
SERIAL NO. 4022127
LOAD / UNLOAD SYSTEM
MAHA 20"W X 42"L MOTORIZED STEEL INTERLOCK BELT CONVEYO
MAHA 20"W X 60"L MOTORIZED INCLINE STEEL SEPARATOR BELT CONVEYOR
MAHA 4,000-LB. HYDRAULIC BIN TIPPER
BUILT IN HYDRAULIC POWER SUPPLY
OFF LOAD CHUTE
MOTORIZED LOADER WITH SERVO DRIVEN LOADING ARM
10"W X 100"L MOTORIZED STEEL INTERLOCK BELT CONVEYOR
GEAR REDUCTION VARIABLE SPEED DRIVE MOTOR
 
  21
IDMA33022
MakeManzoni
ModelSR-1300
YOM1991
ConditionGood Condition
PhotoSee Photo
CAPACITY: 1300-METRIC TON
STROKE : 10"
AIR CLUTCH AND BRAKE
AIR COUNTER BALANCE
(3) LOWER DIE HOLDERS
FOOT PEDAL CONTROL
2015 AJAX TOCCO PACER 1 IN-LINE BILLET INDUCTION HEATER
CAPACITY: 500KW
CHAIN LINK CONVEYOR
2-ROLL PINCH ROLL
BILLET LOADER
MAIN CONTROL PANEL
2006 MAHA VIBRATORY CONVEYOR
SERIAL NO. 23691
MAHA 3,500 POUND CAPACITY HYDRAULIC TRIPPER
BUILT IN HYDRAULIC POWER SUPPLY
12"W X 20'L MOTORIZED STEEL MESH CONVEYOR
COOLING FANS
STAND ALONE HYDRAULIC LUBRICATION STATION
TOUCH PAD CONTROL AND LED DISPLAY
 
  22
IDMA33021
MakeAjax
Model
YOM1997
ConditionGood Condition
PhotoSee Photo
COMPLETE REBUILD IN 1997
1300 capacity
10" STROKE
30" OPEN HEIGHT
70 STROKES PER MINUTE
32" L-R X 33" F-B BED
31" L-R X 31" F-B RAM
2016 AJAX TOCCO PACER 1 INDUCTION BILLET HEATER SYSTEM
480 VOLTS, 400 KW
EQUIPPED WITH:
AEG ELETTRONICAF INDUCTION BILLET HEATER
V TYPE CHANNEL FEED
5"W MOTORIZED STEEL MESH INCLINED CONVEYOR
36"W X 84"L MOTORIZED STEEL SLOT CONVEYOR
MOTORIZED BILLET PUSHER
VARIABLE SPEED GEAR REDUCTION DRIVE MOTOR
4,000-LB. HYDRAULIC BIN TIPPER
 
  23
IDMA32928
MakeHosung Korea
ModelHFP-1300
YOM
ConditionGood Condition
PhotoSee Photo
Capacity : 1300 ton
Stroke : 225 mm
Stroke per Minute : 90
Slide Area : 860 x 970 mm
Bed Area : 1050 x 1050 mm
Die Height : 720 mm
Slide Adjustment : 8 mm
Upper Ejector : 15 mm
Lower Ejector : 45 mm
Main Motor : 75kw x 8p
Trimming Press
Make : Dongwoo
Model : DS150

400 kw Induction Heater
 
  24
IDMA32924
Make
Model
YOM2008 between 2009
ConditionGood Condition
PhotoSee Photo  |  See Video
1. Press Type:Four column push down Oil hydraulic system
2. Nominal force (static working pressure of 320 bar): 5,000 Tons
3. Up-setting force (static working pressure of 420 bar): 6,500 Tons
4. Daylight: 4,700 mm
5. Stroke of Movable cross head: 2,700 mm
6. Main Ram dia (Center cylinder): 1 set - ¢950 mm
7. Side Ram dia (Side cylinder): 2 sets - ¢750 mm
8. Return cylinder Ram dia: 2 sets - ¢300 mm
9. Moving Table: Width 2,600ΧLength 6,600 mm
10. Moving Table stroke (center to both side 2,750 mm):5,500 mm
11. Approaching speed:300 mm/sec
12. Main cylinder Forging speed (2,200 tons/ 320 bar):163 mm/sec
13. All cylinder Forging speed (5,000 tons/ 320 bar):73 mm/sec
14. Up-setting Forging speed (6,500 tons/ 420 bar):10 mm/sec
15. Return speed: 270 mm/sec
16. Hydraulic Main pump: 12 sets Rexroth Plunger Pump (A7VO+A2FO)
17. Electric Main Motor:12 sets 300 Kw 6p 3.3 KV – 3,600 Kw HYUNDAI
18. Main Tank volume: 42,000 Litter
19. Overall dimension:Height above of floor level 13,400 mm Depth 3,760 mm
20. Weight of press:Approx. 1,200 ton
21. Attachment Equipment
1) Tool shifting device:Stroke 4,800 mm
2) Top die clamping device:30 Tons
3) Die magazine device:4 stages
4) Pop-up turn table (for ingot):50 tonsΧ¢1,300 mm


80T-160MT Rail Bound Manipulator
Nominal carrying capacity:80 Tons
Load moment:160 Meter-Tons
Tongs openings: max ¢2,200 / min ¢420 mm
max Turning diameter:¢3,600 mm
min. Tongs central height above rails: 1,800 mm
max. Tongs central height above rails:3,000 mm
Vertical stroke of tongs parallel to floor:1,200 mm
Vertical tilting angle of tongs:Up 13.8 degree / Down 13.8 degree
Horizontal side shift of tongs:400 mm
Horizontal slew angle of tongs/:± 13 degree
Central rail distance:4,200 mm
Rotation speed: max 16 rpm
Travelling speed: 30~330/660 mm/sec
Lifting speed: 120 mm/sec
Travelling Distance: 18 meter
Hydraulic Main pump: 4 sets Rexroth Plunger Pump (A7VO)
Electric Main Motor: 4 sets 132 Kw 6p 440 V – 528 Kw HYUNDAI
Overall dimension: Height 5,200 mm Width 6,700 mm Length 15,700 mm
Weight of manipulator: Approx. 400 ton

Radial – Axial Ring Rolling Machine
Outside Diameter of Finished Ring: 1,200 ~ 6,300 mm
Height of Finished Ring: 80 ~ 1,000 mm
Inside Diameter of Ring Blank for Mandrel Diameter ¢300 mm: min 320 mm
Height of Ring Blank: max 1,050 mm
Ring Weight: max approx. 12,000 Kg
Radial Rolling Force: max 300 Ton
Main Roll Diameter: ¢1,200 mm
Rolling Speed: max. approx. 1.7 m/sec
Horizontal Stroke of Mandrel: 1,000 mm
Axial Rolling Force: 250 Ton
Length of Taper Theoretical: 1,400 mm
Taper Cone Angle: 35˚
Horizontal Stroke of Axial Roll Stand: 5,700 mm
Vertical Stroke of Upper Axial Roll: 1,050 mm
Max Distance Between the Axial Roll: 1,120 mm
Main Roll Driving Motor: DC710KwΧ570Volt
Axial Roll Driving Motor: DC710KwΧ570Volt
Hydraulic Main Pump Motor: 4 sets-90 KwΧ440 VoltΧ60 Hz
Cooling Circulation Motor: 2 sets-3.7KwΧ440VoltΧ60Hz
Hydraulic Pump: 4sets-A4V-180 (REXROTH)
Max Total Flow:720 Litter/min
Operation Pressure: 210 Kg/㎠
Grease Lubrication Unit: 2 sets
 
  25
IDMA32868
MakeHosung Korea
ModelHFP700
YOM2007
ConditionGood Condition
PhotoSee Photo
Capacity : 700 ton
Stroke : 180 mm
Stroke per minute : 100 mm
Slide area : 700 x 780 mm
Bed area : 730 x 890 mm
Die height : 540 mm
Slide adjustment : 10 mm
Upper ejector : 20 mm
Lower ejector : 30 mm
Main motor : 45 kw
Induction Heater
Manufacturer : Myeongin
Model : IHB242-400
Capacity : 400kw, 2.5khz
Input power : 580V, 60Hz
Control Voltage : AC 380V / AC 220V
Trimming Press
Manufacturer : Dongsung
Model : CS-80
Capacity : 80 ton
 
  26
IDMA32864
MakeHosung Korea
ModelHFP1000
YOM2010
ConditionGood Condition
PhotoSee Photo
Capacity : 1000 ton
Stroke : 200 mm
Stroke per minute : 95
Slide area : 760 x 870 mm
Bed area : 950 x 1050 mm
Die height : 620 mm
Slide adjustment : 8 mm
Upper ejector : 15 mm
Lower ejector : 45 mm
Main motor : 75 kw x 8P
Induction Heater
Manufacturer : Myeongin
Model : IBH242-401
Y.O.M : 2010
Capacity : 400 kw / 2.4 Khz
Input power : 3P. 580V 60Hz
Control voltage : AC380V, AC220V
Trimming Press
Manufacturer : Woojin
Model : WS-150
Y.O.M : 2010
Capacity : 150 ton
Stroke : 200 mm
Number of stroke : 40
Die height : 450
Slide adjustment : 100 mm
 
  27
IDMA32845
MakeHosung Korea
ModelHFP1600
YOM2011
ConditionGood Condition
PhotoSee Photo  |  See Video
- Capacity : 1600 ton
- Stroke : 255 mm
- Stroke per minute : 85
- Slide area : 1000 x 1050 mm
- Bolster area : 1310 x 1250 MM
- Die height : 950 mm
- Slide adjustment : 10 mm
Induction Heater
Manufacturer : 4M Induction
Model : 4MB122-900
Y.O.M : 2011
- Voltage : 3P 720V
- Ampere : 1200 KVA
- Output power : 900 kw
- Output voltage : 1080 V
- Frequency : 1.2 khz
Trimming Press
- Manufacturer : Woojin
- Model : WS-200
- Capacity : 200 ton
 
  28
IDMA32570
MakeFPM
Model
YOM
ConditionGood Condition
PhotoSee Photo
Line made with
Automatic disc saw Adige CM 501
Screw press DELLAVIA Modele LECCE
Electronic Automation
Induction system 50 KW
Triming unit
Band Saw
Mini maxi cap dia 10 / 60 mm
main motor 5.5 kw
cutting length 5 / 500 mm
Clamping force 350/1700 Da N
Coolant tank cap 78 L
Hydraulic unit cap 200 L
Approx weight 1300 kgs
Electric components Siemens
Screw press
Screw dia 130 mm
Nominal power 160 Tons
Max power 250 Tons
Limit forging power ( spotting ) 310 Tons
Distance between upright 350 mm
Distance between guide 370 mm
Ram stroke 300 mm
Distance between table and guides 250 mm
Approx. size H 3130 x D 1880 x W 1740 mm
Main motor 7.5 Kw
Approx. weight 4.8 tons
Main supply 400v / 230v 50hz
PLC Siemens S7-300
Total power requirement 7.5 kw
Pneumatic system to blow the scories
Loading Arm FPM
Vertical / horizontal Positioning
Brushless motors , interpolation with the Press Siemens
Loading cap 1 Kg
Maxi vertical stroke 80 mm
Power electro pneumatic
Lopin transportation belt with infrared control
Automatic dies lubrication 8 points
Modular points high pressures
Ram position control
Lubrication cycle controlled by Timer
75 L tank with alarm low level
Lubricant qty adjustable from 0 to 1.5 cc / or only air blowing
Induction system IHFT 50 Kw
Brand INDUCTION
Material Brass coper
Lopin size L 25 ( maxi 100 mm ) x16 mm dia
heating temperature 750° adjustable
input temperature 20°
Feeding mode 1 Lane
exit mode gravity one by one
Capacity 1000 pcs/h for 16 mm dia length 25 mm or 1600 / hour
Production Maxi 130 kgs/ h at 750°
Converter Specs
Exit M F Power 50 Kw
Nominal power 750V
Power requirement 62.5 Kva Direct to main supply
main supply 400 v – 3 ph – 50 Hz
Cos Phi 0.94 constant
water inlet 20-30 bars
inner circuit pressure loose 0.7 bar
Water supply for generator and induction 52 L/min
Water temperature thermal elevation 10° C
Oven Automatic loading device, one line with constant feeding speed
lopin lift loader
Round pieces
Size max dia 50 mm L 100 mm
Loading mode vrac in a bowl
Loading height 950 mm
Exit level 1850 mm
Triming and finishing line high production
Automatic In insulated cabin
Made of
Loading robot with vision system DRS (DRIVE SYSTEM ROBOT)
Trimming press EASY 25
Wirth transfer for the drilling of finished parts
 
  29
IDMI7103
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging
Model: K8538
630 tons capacity, table size 640 x 820 mm, ram size 600 x 600 mm, ram stroke 200 mm, no of stroke per min 90, shut height 560 mm, slide adjustment 20 mm, ejector stroke - upper 40 mm, lower 40 mm, main motor power 40 kW, dimensions 3065 x 2480 x 4590 mm, weight 42 tons
Wt is 40 tonnes
In Bolster holder Die fits by width as roller 100 mm X blocker 150 mm X finisher 150 mm X 100 mm thick
Load meter is not there
Lubrication is 💯% & perfect
Table size 730 mm length X 640 mm width
2) Trimming Press
3) Induction heater(2013)
 
  30
IDMA32373
Make
Model
YOM
Condition
PhotoSee Photo
1) Press Hot Forging
Make: Ajex
Capacity: 1600 ton
2) Trimming Press
3) Induction Heater
 
  31
IDMA32347
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Hot Forging Press.
Make: National
Model: Maxipress
YOM: 1968
Capacity: 2500 ton,
Stroke: 14"
Shut height: 34.5"
Strokes per minute: 48
Height above floor: 21'
Approximate weight: 386,000 lbs.
Die Seat (Front to Back X Left to Right): 54" X 47.5"
Ram Face (Front to Back X Left to Right): 44" X 42"
Side Openings (Left to Right X Top to Bottom): 30" X 33"

2) Trimming Press
Make: Bliss
Capacity: 150 ton,
3) Induction Heater
Make: American Induction Heating Corporation
Volts: 800
KW: 1250
Freq: 540 HZ
 
  32
IDMI7069
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1. National Maxipress 6000 ton - 1 nos,
2. Minster press 40-11- 2 nos,
3. Furnace for forging - 3 nos.
 
  33
IDMA32110
Make-
Model--
YOM
ConditionGood Condition
PhotoSee Photo
1. Forging Press
Make:SIMPELKAMP
Type: 12000/16000 KN
YOM: new 1986
Force of pressure: 1645 t
Stroke :1000 mm
Day light: 3000 mm
Lowering speed: 280 mm/sec
Reverse speed: 275/346 mm/sec
Distance of column: 2520 mm
2. Manipulator
Manufacturer manipulator: DANGO & DIENETHAL
Type: S 30.1 SVS
New: 1986
Swivelling range of tongs – up 6,5 °
Swivelling range of tongs – down 12,5 °
Side shift to left 200 mm
Side shift to right 200 mm
Turning speed of tongs 2 – 30 rpm
Driving speed, 2 steps 0 – 60 m/ min
Tongs opening max. 1040 mm
Load 12 t
Required power 130 kW
Width of work piece 880 mm
Weight of machine approx. 63,3 t
Includes a moving table and some spare parts, a spare column/frame and a spare tension rod
 
  34
IDMA32056
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1. 40 ton counter blow hammer
Make:Beche(Schluer)
Year:1971
Model:DG40H
Stroke:1400 mm
SPM:40
Daylight between the guide:1400 mm
Depth of tub:2000 mm
Height above floor:5880 mm
Total weight: 245 ton
Including :Spare Up and down Rams

2. 1500 ton trimming press
Make: Wilkins & Mitchell(Schluer)
Year of manfacture:1974
Capacity:1500 t
Stroke:400 mm
SPM:10
Shut height:875 mm
Slide area: 2390 x 1830 mm
Bolster area: 2400 x 1830 mm
Main motor:150 HP
Total weight:173 ton
 
  35
IDMA31949
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press hot forging
Make: Hosung
Capacity: 2500 ton,
Stroke length (mm) 320
Stroke per mirule (spm) 75
Die Height (mm) 1000
Slide Adjustment (mm) 10
Slide area (mm x mm) 1200*1250
Bad area (mm x mm) 1370*1250
Upper ejector (mm) 20
Lower ejector (mm) 60
" Production capacity EA/M: 140,000

2) Trimming Press
Capacity: 250 ton,
3) Induction Heater: 1200 KW
Spare Parts:
"ㅁ. H / COIL (Φ60 / 70/80/90)
ㅁ. QCD Pump
ㅁ. Sol Valve (32A / 40A)
ㅁ. Slide hydraulic pump"
"Forged products weight (Kg): 2.21~17.24
 
  36
IDMA31948
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press hot forging
Make:Korean
Capacity: 1600 ton,
Stroke length (mm) 300
Stroke per mirule (spm) 75
Die Height (mm) 660
Slide Adjustment (mm) 10
Slide area (mm x mm) 860*910
Bad area (mm x mm) 940*1200
Upper ejector (mm) 20
Lower ejector (mm) 45
" Production capacity EA/M: 193,000

2) Trimming Press
Capacity: 160 ton,
3) Induction Heater: 800 KW,
Spare parts:
"ㅁ. H / COIL (Φ40 / 50/60/70/80)
ㅁ. QCD Pump
ㅁ. Sol Valve (32A / 40A)"
"Forged products weight (Kg): 0.77~5.96
 
  37
IDMA31947
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press hot forging
Model: DFP 1350
Make: Dingwoo
Capacity: 1350 ton
Stroke length (mm) 225
Stroke per mirule (spm) 90
Die Height (mm) 640
Slide Adjustment (mm) 8
Slide area (mm x mm) 880*880
Bad area (mm x mm) 900*1050
Upper ejector (mm) 20
Lower ejector (mm) 45
" Production capacity EA/M ": 193,000

2) Trimming press
Capacity: 200 ton,
3)Induction Heater : 500 KW,
Spare parts:
"ㅁ. H / COIL (Φ55 / 60/70)
ㅁ. Leak valve (300Kgf / ㎠)
ㅁ. Pressure switch (135 ~ 185Kgf / ㎠)
ㅁ. QCD Pump
ㅁ. Sol Valve (32A / 40A)"
"Forged products weight (Kg): 2.23~2.92
 
  38
IDMA31946
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging
Make: Russian
Capacity: 1000 ton,
Stroke length: 250 (mm)
Stroke per mirule: 90 (spm)
Die Height: 560 (mm)
Slide Adjustment: 8 (mm)
Slide area: 720*720 (mm x mm)
Bad area: 990*770 (mm x mm)
Upper ejector: 20 (mm)
Lower ejector: 40 (mm)
" Production capacity EA/M : 279,000

2) Trimming press
Capacity: 160 ton,
3) Induction Heater: 500 KW,
Spare parts:
"H / COIL (Φ40 / 50/60)
ㅁ. Leak valve (300Kgf / ㎠)
ㅁ. Pressure switch (135 ~ 185Kgf / ㎠)
ㅁ .QCD Pump
ㅁ. Solvent Valve (32A / 40A)"
"Forged products weight (Kg)"0.16~0.96
 
  39
IDMA31941
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging
Model: JFP750,
Make: Jaewoo
Capacity: 750 ton,
Stroke length:190 mm
Stroke per mirule : 98 (spm)
Die Height: 580 (mm)
Slide Adjustment: 8 (mm)
Slide area : 740*780 (mm x mm)
Bad area: 810*900 (mm x mm)
Upper ejector : 20 (mm)
Lower ejector : 40 (mm)
Main motor: 75 Hp
Production capacity
EA/M: 279,000
2) Trimming press.
Capacity: 110 ton
3) Induction Heater
350 KW
Spare parts
ㅁ. H / COIL (Φ30 / 40/50/60)
ㅁ. Leak valve (300 Kgf / ㎠)
ㅁ. Pressure switch (135 ~ 185 Kgf / ㎠)
ㅁ. .QCD Pump
ㅁ. Solvent Valve (32A / 40A)"
Forged products
weight (Kg): 0.13~1.16
 
  40
IDMA31551
Make
Model
YOM
Condition
PhotoSee Photo
1) Hot forging press
Make: SMERAL
Model: LZK 2500
Nominal effort: 2500 tons
Table size:
-Left-to-right: 1340 mm
-Front-to-back: 1400 mm
Slide stroke: 320 mm
Slide adjustment: 10 mm
Max. number of courses per 1 min: 65 mm
Shut height: 905 mm
Capacity of the electric motor: 130 kW
Dimensions: 4035 x 4055 x 7390 mm
Weight: 140 tn.
2)Trimming press
Make: VALDRANO
Capacity: 300 t.
Slider stroke: 200 mm.
Adjustment: 100 mm.
Length of a rod: 1080 mm.
Bed overall dimensions:
width — 1050 mm.
depth — 1000 mm.
Slider overall dimensions:
width — 850 mm.
depth — 900 mm.
Max distance between bed and ram: 750 mm.
Slider strokes per minute: 50
Main motor: 25 kW
Motor speed: 1500 rpm
3) Induction heater
Model: IMF 1500 K1
tatic frequency converter for induction heating, type IMF 1500 K1 combined with hot cutting line:
Nominal tension: 6Χ440 V
Nominal frequency: 50 Hz
Nominal current: 1100 A
Max. current: 1200 A
Short-circuit current: 50 kA
Out power: 1500 kW
Apparent power: 1680 kVA
Max. power factor: 0.93
Min. environmental temperature: 5 °C
Max. environmental temperature: 50 °C
Max. percentage of humidity: 95 %
4) Robot KUKA
Model: KR 150-2 2000
Maximum reach: 3,100 mm
Rated payload: 150 kg
Suppl. load, arm/link arm/rotating col: 50/100/300 kg
Suppl. load, arm + link arm, max. 100 kg
Maximum total load :550 kg
Number of axes 6
Mounting position Shelf-mounted, floor
Variant Cleanroom, Foundry
Positioning repeatability* ±0.06 mm
Path repeatability*
Controller KR C2 edition2005
Weight (excluding controller), approx: 1,445 kg
Temperature during operation +10 °C to +55 °C
Protection classification IP 65
Robot footprint 1,006 mm x 1,006 mm
Connection 7.3 kVA
Noise level 75 dB
5) Billet shear
Make: FICEP
Model: CTCH 100
 
  41
IDMA31430
MakeWeingarten
Model
YOM2006
ConditionGood Condition
PhotoSee Photo  |  See Video
Mechanical crank press Type PK 1000.S
Press capacity: 12.500 kN
Working capacity: 225 kJ
Two point drive
Strokes: 40 to 60 strokes/ minute
Stroke: 300mm
Tool stations: 4
Stroke adjustment: +/- 5mm
Table size: 1050 x 1100mm
Crankshaft turning speed: 120 min-1 with 60 strokes/ minute
Options:
Ejector stroke table: 55mm
Ejector force table: 3x 1000 kN
Ejector stroke ram: 15mm
Ejector force ram: 3 x 500 kN
4-point table cushion: 4 x 1000 kN x 50mm stroke
4-pont ram cushion: 4 x 1000 kN x 50mm stroke
Tool changing wagon: Carrying capacity 3000kg
Automation:
Automated part feeder: 30 parts/ minute x 1000mm length
Electronic transfer: 3 axes
Feed motion 315mm
Closing 100mm per side
Lifting 60mm
The speed forge drive is adjustable so that it can be individually programmed according to the forging process.
The contacting time of the forging part can be up to half of the normal contacting time compared with conventional presses.
 
  42
IDMA31306
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Type -Hot Forging Press
Make Kurimoto/Smeral
Model LKM-1600
Capacity 1600 ton
Stroke 280 mm
Shut Height 760 mm
Ram Adjust 14 mm
SPM continuous 85
SPM single 22
Table 1243 x 1360 mm
Slide 920 x 1040 mm
Upper Ejector Capacity 3 ton
Upper Ejector Stroke 20 mm
Bottom Ejector Capacity 20 ton
Bottom Ejector Stroke 50 mm
Main Motor 75 Kw
2 )Machine Type - High Frequency Billet Heater
Make - Fuji Denki
Model IH-STB
Frequency 3 Khz
Capacity 200 Kw
Temperature 1250C
Max Bar Weight 410 kg
Max Bar Dia 65 mm
Max Bar Length 155 mm
Min Bar Dia 42 mm
Min Bar Length 80 mm
3) Machine Type Knuckle Press
Make Aida
Model PK-VK-400
Capacity 400 ton
Stroke 140 mm
SPM 45
Bolster 600 x 480 mm
Slide 400 x 370 mm
Die Height 370 mm
Adjust 15 mm
Knockout 20 ton
Knockout Stroke 70 mm
Main Motor 30 Kw
4) Machine Type Mechanical Press
Make Shinohara
Model SG-200A
Capacity 200 ton
Stroke 180 mm
SPM 40
Shut Height 515 mm
Adjust 100 mm
Bolster 1000 x 1000 mm
Slide 990 x 990 mm
5) Machine Type Mechanical Press
Make Yodogawa
Model PBS
Capacity 150 ton
Stroke 100 mm
SPM 45
Bolster 1000 x 450 mm
Slide 1000 x 450 mm
Shut Height 330 mm
Main Motor 18.5 Kw
 
  43
IDMA31247
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1. Machine Type : Hot Forging Press
Make : kurimoto/smeral
Model : LKM-1600
Capacity : 1600 ton
Stroke : 280 mm
Shut Height : 760 mm
Ram Adjust : 14 mm
SPM continuous : 85
SPM single : 22
Table : 1243 x 1360 mm
Slide : 920 x 1040 mm
Upper Ejector Capacity : 3 ton
Upper Ejector Stroke : 20 mm
Bottom Ejector Capacity : 20 ton
Bottom Ejector Stroke : 50 mm
Main Motor : 75 Kw
2. Machine Type : High frequency Billet Heater
Make : Fuji Denki
Model : IH-STB
Frequency : 3Khz
Capacity : 200 Kw
Temperature : 1250c
Max Bar Weight : 410 kg
Max Bar Dia : 65 mm
Max Bar Length : 155 mm
Min Bar Dia : 42 mm
Min Bar Length : 80 mm
3. Machine Type : Knuckle Press
Make : Aida
Model : PK-VK-400
Capacity : 400 ton
Stroke : 140 mm
SPM : 45
Bolster : 600 x 480 mm
Slide : 400 x 370 mm
Die Height : 370 mm
Adjust : 15 mm
Knockout : 20 ton
Knockout Stroke : 70 mm
Main Motor : 30 Kw
4. Machine Type : Mechanical Press
Make : Shinohara
Model : SG-200A
Capacity : 200 ton
Stroke : 180 mm
SPM : 40
Shut Height : 515 mm
Adjust : 100 mm
Bolster : 1000 x 1000 mm
Slide : 990 x 990 mm
5. Machine Type : Mechanical Press
Make : Yodogawa
Model : PBS
Capacity : 150 ton
Stroke : 100 mm
SPM : 45
Bolster : 1000 x 450 mm
Slide : 1000 x 450 mm
Shut Height : 330 mm
Main Motor : 18.5 Kw
 
  44
IDMA31102
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Make : VORONEZH
Model : K8544
YOM : 1978
pressure : 2500 t
stroke : 350 mm
daylight : 890 mm
table surface area : 1400x1200 mm
no. of strokes : -60 Hub/min
ram head dimension : 1120x1070 mm
total power requirement : 130 kW
weight of the machine ca. : -- -- t
dimensions of the machine ca. ---- m
Accessories
With
HANOUL Trimming Press, new 2007,
300 t capacity, stroke 300 mm, 30 SpM
and :
600 kW High Frequency Induction Heater
 
  45
IDMA30723
Make
Model
YOM
Condition
PhotoSee Photo
Manufacturing date : 2014
Maker : J&H Press, Korea
It is available as a package (1000ton hot forging press including die-set + induction heater including billet loader and step feeder + 110ton trimming press)
 
  46
IDMA30665
MakeVoronezh
ModelKB8040
YOM1993
Condition
PhotoSee Photo
Rated Capacity................... 1000 Metric Tons
Slide Stroke..................... 250 MM
Minimum Enclosed Die Space....... 560 MM
Die Space Adjustment............. 20 MM
Strokes Per Minute............... 90
Slide (ram) Dimensions mm ....... 720x720
Table Dimensions mm.............. 990 x 770
Top Knockout Stroke.............. 20 MM
Bottom Knockout Stroke........... 40 MM
Press Length..................... 4350 MM
Press Weight..................... 3500 MM
Total Height Above Floor......... 5145 MM
Main Electric Motor.............. 55 KW
Updated with new plc control (technology)
 
  47
IDMA30649
MakeVoronezh
ModelKB8040
YOM1993
Condition
PhotoSee Photo
Rated Capacity................... 1000 Metric Tons
Slide Stroke..................... 250 MM
Minimum Enclosed Die Space....... 560 MM
Die Space Adjustment............. 20 MM
Strokes Per Minute............... 90
Slide (ram) Dimensions mm ....... 720x720
Table Dimensions mm.............. 990 x 770
Top Knockout Stroke.............. 20 MM
Bottom Knockout Stroke........... 40 MM
Press Length..................... 4350 MM
Press Weight..................... 3500 MM
Total Height Above Floor......... 5145 MM
Main Electric Motor.............. 55 KW
Updated with new plc control (technology) in 2002
INCLUDES:
- AUTOMATIC MATERIAL FEED SYSTEM TO FURNACE
- SIGMA 60 GAS FIRED AUTOMATIC CONTINUOUS FURNACE, CAPACITY 5500/LBS/HR RECENTLY RELINED.
- SIGMA HOT BAR SHEAR, CAPACITY SQ = 4", ROUND 4-1/4"
- 150 TON MECHANICAL TRIM PRESS
- MISC TOOLING
 
  48
IDMA30644
Make
Model
YOM
Condition
PhotoSee Photo
Complete Kurimoto Model C2F Hot/Warm Forming Line currently setup to
produce the inner and outer bearing race rings. Can be seen
under power in production for 3 more weeks.
1. 1500ton Kurimoto Model C2F-15 Hot/Warm Forging Press with
5-Stations, built 2000s
2. Intec Sizing press Model SSP-200 for outer rings. built, 2001
3. Manyu Model LBS-200 bar shear and feeding rack, built 2001
4. Mitsui Induction heater, 750Kw, 6600Volt, built 2001
5. Extra bolsters, Machine parts, tooling, oil separator, conveyors
1500 Ton Kurimoto Model C2F-15 Hot/Warm
Forging press with 5-Stations, Built 2000s,
Ref. #13130
SPECIFICATIONS:

Built by......................... Kurimoto, Ltd, Osaka, Japan
Capacity........................ 1500ton
Stroke............................ 400mm
Number of strokes......... 30 – 60min.
Continuous inching: 5 min – 1
Single inching when changing dies: 3 min-1
(at stopping decreasing speed: 1 min - 1
Die height...................... 977mm (stroke down on adj up)
Max. permitted eccentric distance:
(Left/Right) ....... 300mm
(forward/aft....... 50mm
Slide adjustment........... 10mm
Bolster dimensions........ 1600x1080x185mm
Adapter dimensions....... 1600x1080x120mm
Column intervals............ 2000mm
Side opening................. 900mm
Lower Knockout............ Max. 400kN (total 1Mn x 100mm)
Main Motor.................... 150kw/ 60hz x 4P
Press height.................. 6300mm

FEATURES:
· Load meter with overload sensor
· Revolutionary Stick release device (hydraulic type)
· Automatic 5-Station transfer system
· Bearing temp. detector (8 x locations)
· Guide gib temp. detector (8 x locations)
· Wide range of allowable eccentric loads
· Die holder change device
· Upper die exchange device
· Die holder clamp lifter
· Die height automatic control unit
· Lubrication cleaning device for press body
· Tool lubrication system
· Flange for Exhaust
· Inner, Outer, Web and Bypass conveyors
 
  49
IDMA30593
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
500ton Tandem Press Line(500-300-300-400ton)
500ton press Fukui(Japan) Model: MDL500
Single action type, Side moving bolster type
Year: 1980
Under power, Link motion type, The number of points:2
Stroke: 701mm
SPM:10-20
Slide adjustment: 500mm
Die height: 1120mm
Slide: 2500 x 1700mm
300ton press Fukui(Japan) Model: MDL300
Single action type, Side moving bolster type
Crank press type, The number of points:2
Year: 1980
Under power
Stroke: 600mm
SPM:8-20
Slide adjustment: 500mm
Die height: 1120mm
Slide: 2500 x 1700mm
-300ton press Fukui(Japan) Model: MDL300
Single action type, Side moving bolster type
Crank press type, The number of points:2
Year: 1980
Under power
Stroke: 600mm
SPM:8-20
Slide adjustment: 500mm
Die height: 1120mm
Slide: 2500 x 1700mm
-400ton press Komatsu(Japan)
Single action type, Side moving bolster type
Crank press type, The number of points:4
Year: 1980
Under power
Stroke: 800mm
SPM:10-24
Slide adjustment: 600mm
Die height: 1300mm
Slide: 3000 x 1700mm
Bolster: 3000mm x1700mm

-Dipstick equipment
Coil hickness:0.5~2.3mm
 
  50
IDMI6782
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1] Press Hot Forging.
Make : TMP - Russian.
Model : KB8540.
Capacity : 1000 ton,
Slide stroke : 250 mm,
Slide stroke number in 1 min : 90,
Adjusting of distance between table and slide : 20 mm,
Upper ejector :- Stroke : 40 mm,
Power : 31,5 kN,
Bottom ejector :- Stroke : 20 mm,
Power : 50 kN,
Table : 770 x 990 mm,
Slide dimension : 720 x 720 mm,
Window size in the column : 1250 x 560 mm,
Press dimension : 4430 x 3500 x 5145 mm,
Total weight : 65700 kg.
2] Press Trimming.
Make : Massy England.
Capacity : 120 tons.
3] Induction Heater.
Make : Elind.
Capacity : 250 Kw,
Qty : 1 set.
Capacity : 300 Kw.
Qty : 1 set.
 
  51
IDMA30388
Make-
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Hot Forging Press
Make: TMP Voronezh
Capacity: 2500 ton,
Ram stroke: 350 mm,
SPM: 60
Shut height: 890 mm,
Ram dimensions: 1120 x 1070 mm,
Upper knoct-out cap: 6.3 ton,
Upper knoct out stroke: 50 mm,
Lower knoct out cap: 10 ton,
Lower knoct out stroke: 50 mm,
Main motor: 130 kw

2) Trimming Press
Model: HNCP300
Make:TMP Voronezh
Capacity: 300 ton,
SPM: 30
Die height:650 mm,
Slide area: 1300 x 800 mm,
Bolster area: 1600 x 900 mm,
Main motor: 37 kw,
Slide adjust: 120 mm
 
  52
IDMI6770
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging
Make: National,USA
Model: Maxipress
Specification:
Capacity : 2500 ton,
Stroke : 350 mm,
Stroke per minute : 55,
Shut Height : 875 mm,
Die Seat F-B x R-L : 1350 x 1200 mm,
Ram Face F-B x R-L : 1100 x 1050 mm,
Floor Space F-B x R-L : 3425 x 4950 mm,
Height above Floor : 6125 mm,
Motor : 150 HP,
Approximate New Weight : 175 tons
2) Trimming Press
Make: TMP Voronezh Russia
Model: KA9033
Specification:
Capacity : 200 ton,
Ram stroke : 200 mm,
Number of ram strokes per min : 50,
Shut height : 450 mm,
Bolster plate to ram adjustment stroke : 20 mm,
Bed dimension : 1,250 x 900 mm,
Ram dimension : 1250 x 800 mm,
Bolster plate thickness : 180 mm,
Main drive motor power : 22 kw,
Overall dimensions : Floor space : 4010 x 2960 mm,
Height above floor level : 4885,
Mass t approx : 41 ton.
 
  53
IDMI6769
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
2) Press Hot Forging
Model: LZK4000
Make: Smeral,Czech
Capacity : 4000 tons,
Ram stroke : 380 mm,
Number of ram strokes : 60/1 min,
Width between uprights : 1580 mm,
Shut height : 1000 mm,
Ram adjustment : 20 mm,
Table size : 1520 x 1600 mm,
Slide size : 1470 x 1400 mm,
Stroke of upper ejector : 50 mm,
Jecting force of upper ejector : 105 kN,
Stroke of lower ejector : 80 m,,
Ejecting force of lower ejector : 410 kN,
Press height above floor : 8100 mm,
Press dimensions :
Height : 9150 mm,
Width : 4720 mm,
Length : 4640 mm,
Main drive motor output : 200 KW,
Press weight : 250 ton
2) Trimming Press:
Model: KB9540
Make: TMP Voronezh Russia
1000 ton, ram stroke 500 mm, number of ram strokes rate per minute 20, shut height 680 mm, bolster plate to ram adjustment stroke 200 mm, bed dimensions 1250 x 1250 mm, bed opening dimensions 1000 x 1000 mm, ram dimensions 1250 x 1250 mm, bolster plate thickness 260 mm, main drive motor power 75 kW, overall dimensions : floor space 4310 x 3820 mm, height above floor level 6790 mm, mass 79.5 t.
 
  54
IDMA30370
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Main Press Voronezh 2500 ton.
Model : K8544.
Y.O.M : 1973.
Capacity : 2500 ton,
Stroke : 350 mm,
Stroke : 60 n/min,
Shut height : 890 mm,
Ram adjustment : 10 mm,
Table size : 1200 x 1400 mm,
Ram size : 1070 x 1120 mm,
Upper extractor stroke : 0-60 mm,
Lower extractor stroke : 70 mm,
Weight : 203000 kg.
ALTOF meter effort with extensometers CESTARO dies lubrication system die holder with hydraulic locking system.
2] Hot Shearing Line FICEP with bar magazine.
Model : CTCH1000.
Y.O.M : 2001.
Capacity : 10000 kg.
3] Trimming Press Valdarno 300 ton.
Model : VPS DB60.
Y.O.M : 1978.
Capacity : 300 ton,
Stroke : 200 mm,
Ram adjustment : 100 mm,
Daylight : 800 mm,
Wight : 33000 kg.
Sheared workpiece and scrap conveyors.
4] Automated loading / unloading system for trimming process :-3
Brand : Sir,
Set up Year : 2005.
Components :
KUKA Anthropomorphic robot
Model : KR150 2000-2.7,
Capacity : 200 kg.
KUKA control unit.
Model : KRC2.
5] Induction furnace induction :-
Type : IMFR1200K2.
Power : 1200 Kw,
Frequency : 1 KHz,
Y.O.M : 2001.
It comes with two sets of inductors consisting of 4 one meter coil for 48-85 mm squared billets.
 
  55
IDMA30046
Make
Model
YOM
ConditionGood Condition ,Not under power
PhotoSee Photo
A] 750 Ton Hot Forging Press Line :-
1] Induction Heater :-
Manufacturer : Insung Electric machinery Co. Ltd (Korea).
Model : ISR262-400.
YOM : 2004.
Capacity : 400 kw.
2] Hot Forging Press :-
Make : Jaewoo (Korea).
Model : JFP-750.
YOM : 2004.
Capacity : 750 ton,
Stroke : 190 mm,
SPM : 100,
Die height : 560 mm,
Slide adjustment : 8 mm,
Slide area : 740 x 780 mm,
Die set : 780 x 900 mm,
Slide opening : 420 x 630 mm,
Upper knockout stroke : 20 mm,
Lower knockout strike : 40 mm.
3] Trimming Press :-
Make : Ssangyong (Korea).
Model : CS110.
YOM : 2004.
Capacity : 110 ton,
Stroke : 180 mm,
SPM : 25~60,
Die height : 380 mm,
Slide adjustment : 100 mm,
Bolster area : 1100 x 650 mm,
Slide area : 600 x 500 mm,
Bolster thickness : 105 mm,
Main motor : 11 kw x 4P,
slide adjusting motor : 0.75 kW x 4 P.
 
  56
IDMA30045
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
A] 1000 Ton Hot Forging Press Line :-
1] Induction Heater :-
Manufacturer : Myeongln (Korea).
Model : IBH242-601
YOM : 2014.
Capacity : 600 kw.
2] Hot Forging Press :-
Make : Jaewoo (Korea).
Model : JFP1000.
YOM : 2014.
Capacity : 1000 ton,
Stroke : 220 mm,
SPM : 90,
Die height : 660 mm,
Slide adjustment : 8 mm,
Slide area : 830 x 880 mm,
Die Set : 900 x 950 mm,
Slide opening : 470 x 680 mm,
Upper knockout stroke : 25 mm,
Lower knockout stroke : 50 mm.
3] Trimming Press :-
Make : Hanoul (Korea).
Model : HNCP-110.
YOM : 2014.
Capacity : 110 ton,
Stroke : 150 mm,
SPM : 35~55,
Die height : 450 mm,
Slide adjustment : 90 mm,
Bolster area : 1100 x 600 mm,
Slide area : 900 x 500 mm,
Bolster thickness : 110 mm,
Main motor : 15 kW x 4 P.
slide adjusting motor.
 
  57
IDMA30044
Make
Model
YOM
ConditionGood Condition ,Not under power
PhotoSee Photo
A] 1000 Ton Hot Forging Press Line :-
1] Induction Heater :-
Manufacturer : Insung Electric machinery Co. Ltd (Korea).
Model : MAGII-550.
YOM : 2007.
Capacity : 550 kw.
2] Hot Forging Press :-
Make : Jaewoo (Korea).
Model : JFP1000.
YOM : 2007.
Capacity : 1000 ton,
Stroke : 220 mm,
SPM : 90,
Die height : 660 mm,
Slide adjustment : 8 mm,
Slide area : 830 x 880 mm,
Die Set : 900 x 950 mm,
Slide opening : 470 x 680 mm,
Upper knockout stroke : 25 mm,
Lower knockout stroke : 50 mm.
3] Trimming Press :-
Make : Nagao (Japan).
Model : NCP-1000.
YOM : 1984.
Capacity : 100 ton,
Stroke : 180 mm,
SPM : 45,
Die height : 450 mm,
Slide adjustment : 80 mm,
Bolster area : 1100 x 680 mm,
Shank hole dia : 50,
Bolster thickness : 110 mm,
Main motor : 7.5
slide adjusting motor : 0.4 kW.
 
  58
IDMA30043
Make
Model
YOM
ConditionGood Condition ,Not under power
PhotoSee Photo
A] 1350 Ton Hot Forging Press Line :-
1] Induction Heater :-
Manufacturer : Yooan (Korea).
Model : YA2076.
YOM : 2010.
Capacity : 600 kw.
2] Hot Forging Press :-
Make : Hanoul (Korea).
Model : HNFG1350.
YOM : 2010.
Capacity : 1350 ton,
Stroke : 240 mm,
SPM : 90,
Die height : 730 mm,
Slide adjustment : 10 mm,
Slide area : 87 x 910 mm,
Bolster area : 920 x 1050 mm,
Bolster thickness : 100 mm,
Main Motor : 7.5 Kw.
3] Trimming Press :-
Make : Seoul (Korea).
Model : SSC160.
YOM : 2000.
Capacity : 160 ton,
Stroke : 200 mm,
SPM : 45,
Die height : 500 mm,
Slide adjustment : 100 mm,
Bolster area : 1300 x 800 mm,
Slide area : 1000 x 700 mm,
Bolster thickness : 140 mm,
Main motor : 19 kw x 4P,
slide adjusting motor : 0.75 kW.
Cushion : 15 ton / Stroke : 120 mm.
 
  59
IDMA29625
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Housung HFP 750T,
IHB : 302-500,
Induction Heater : 500 Kw,
3Khz.
 
  60
IDMA29624
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
LKM 830 t,
Induction Heater : 400Kw,
3Khz.
 
  61
IDMA29623
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Housung HFP 1300t,
HS.160 CS Press,
Induction Heater 500Kw,
2.4 Khz.
 
  62
IDMA29622
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
National Maxi Press 1600 t,
Induction Heater : 500 Kw,
3 Khz……
 
  63
IDMI6427
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
Plant production capacity 400Ton Per Month Forged Round and Square Bar Manufacturing
Boiler 14kg presser 3 Ton, - Nos. 1.
Compressor 150 HP - Nos. 4.
Air Receiver Tank each 20 Litter - Nos.4
Furnaces Oil Tank 20 Litter - Nos.1
Furnaces Oil Tank 5 Litter - Nos.1
Transformer 500 KWA - Nos.1
Electric control panel 500 KWA - Nos.1
Open die Hammer 7 Ton - Nos.1 :-
Mobile Manipulator 10Ton - Nos. 1
Welding generator Machine 30HP - Nos.1
EOT Crane 8Ton - Nos. 1
EOT Crane 2Ton - Nos. 1
Jib Crane 3 Ton - Nos. 1
Lathe machine 24” x 24” x 24’ - Nos. 1
Band saw 600 mm x 400 mm - Nos. 1
Hydraulic Drill Capacity 1" to 4" - Nos. 1
Pre Heating Furnace – 3920 X 2135 X 914 mm Oil Fire Furnace - Nos. 1
400 KWA Electric connection.
Lend Area 2000Sq meter total cover of sad of fabrication (Value Per Meter 40000).
Sell Rate With Land: (18Cr INR ).
Sell Rate Without Land : (10 Cr INR).
 
  64
IDMA29023
MakeSmeral,Czech
ModelLZK1600
YOM1983
ConditionGood Condition
PhotoSee Photo
Capacity : 1600 ton,
Stroke : 280 mm,
Adjust : 10 mm,
Shut Height : 750 mm,
Stroke per minute : 85,
Table : 1180 x 1120 mm,
Ram : 1000 x 920 mm,
Top Knockout Stroke : 40 mm,
Bottom Knockout Stroke : 60 mm,
Knockout Pins : 3,
Knockout Pin Pitch : 240 mm,
Knockout Pin Dia : 60 mm,
Press Dimensions : 2750 x 3400 x 6240 mm,
Height Above FL : 5700 mm,
Main Motor : 75 kw x 10p,
Press Weight : 85 tons.
Include the 180 ton Komiyama trimming press, the 400 Kw induction heater, and the billet feeder if you need them
 
  65
IDMA28771
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging :-
Make : Voronezh,
Year : 1990.
Capacity : 1000 tons,
Stroke : 250 mm,
SPM : 90,
Die Height : 560 mm,
Adjust : 20 mm,
Bolster : 770 x 950 mm,
Slide : 720 x 720 mm,
Main Motor : 55 kw x 8p,

2) Trimming Press :-
Make : Baba.
Capacity : 150 ton,
Stroke : 200 mm,
SPM : 45,
Die Height : 480 mm,
Adjust : 100 mm,
Slide : 650 x 650 mm,
Bolster : 1000 x 1000 mm,
Main Motor : 11 Kw x 4p,
Die Cushion : 10 tons,
Cushion Stroke : 70 mm,
Pad Size : 400 x 400 mm,
Pin Length : 130 mm,
Cushion Stroke : 70 mm,
KO Pin Length : 80 mm,

3) Induction Heater :-
Make : Fuji Electric.
Capacity : 210 Kw,
Large die : 55 - 46,
Medium die : 46 - 34,
Die : 200 x H 300.
 
  66
IDMA28770
Make
Model
YOM1986
ConditionGood Condition
PhotoSee Photo
1) Screw Type Forging Press :-
Make : Fuji Sharyo.
Model : PF-500-400.
Year : 1986.
Capacity : 500 ton,
Stroke : 350 mm,
SPM : 31,
Daylight : 900 mm,
Slide : 575 x 675 mm,
Table : 675 x 800 mm,
Knockout Capacity : 8 ton x 2,
Knockout Stroke : 200 mm,
Main Motor : 200V 6P 37 Kw.
2) 75 ton Nagao Trimming Press :-
Type : C Frame Press.
Make : Nagao.
Model : NCP-75.
Capacity : 75 ton,
Stroke : 150 mm,
SPM : 60,
Die Height : 345 mm,
Slide Adjust : 75 mm,
Bolster : 900 x 500 mm,
Slide Adjust : 550 x 450 mm,
Die Cushion : 5.5 tons,
Cushion Pad : 440 x 300 mm,
Cushion Stroke : 50 mm,
Main Motor : 5.5 Kw.
3) Induction Heater :-
Make : Fuji Electric.
Capacity : 180 Kw,
Large die : 35 - 23,
Medium die : 22- 9,
Die : 200 x H300.
 
  67
IDMA28738
Make
Model
YOM
ConditionGood working condition
PhotoSee Photo
1) Press Hot Forging :-
Make : Farina.
YOM : 1988.
Capacity : 650 ton,
Stroke : 200 mm,
Vertical clearance max : 650 mm,
Horizontal light : 660 mm,
Table size : 660 x 900 mm,
Ram Adjustment : 10 mm,
Continuous stroke : 60,
Motor power : 50 Kw,
Weight : 40000 kg.
2) Billet Shear :-
Make : FICEP.
YOM : 1999.
Cady 52.
Is between 12 and 52 mm.
3) Induction Fournace :
GH, are between 18 an 24 mm.
Used by plant could be larger diameter done on this heater.
Transformer included.
 
  68
IDMA27937
MakeKomatsu
ModelCAH1600
YOM1975
ConditionGood Condition
PhotoSee Photo
1) Hot Forging Press
Model: CAH1600,
Make: Komatsu (Japan),
YOM: 1975,
Capacity: 1600 ton,
Slide stroke: 280 mm,
Shut height: 780 mm,
Adjustment: 15 mm,
SPM: 70,
Slide size: 950 x 900 mm (left and right x front and rear),
Bed size: 1050 x 1150 mm (left and right x front and rear),
Balancer capacity: 2.8 tons,
Air pressure: 5 kg/cm2,
The main motor: 75 kW,
Sergeant : 5 mm dot at its maximum capacity demonstrated when,
2)Trimming Press
Capacity: 200 ton,
3)Heater
Make Mitsui (Japan),
Year: 1998,
Voltage: 1000 v,
3090 HZ,
Burner weight: 1.7 tons.
Quantity No : 3.
 
  69
IDMA27799
Make
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) 500 Ton Trimming Press :-
Make : Jaewoo Press (Korea).
New in : November 2012.
Model : JTP-500.
Capacity : 500 Ton,
Stroke : 350 mm,
Stroke per minute : 30,
Slide adjustment : 100 mm,
Slide area (LR x FB) : 1200 x 1000 mm,
Die set (LR x FB) : 1300 x 1100 mm,
Side opening : 600 x 880 mm,
Main motor (KW x p) : 55 x 6,
Adjust motor (KW x p) : 1.5 x 4,
Working pressure (KG/cm2) : 5,
Main voltage (V) : 380.
2) 3500 Ton Forging Press :-
Make : Jaewoo Press (Korea).
New in : November 2012.
Model : JFP-3500.
Capacity : 3500 Ton,
Stroke : 370 mm,
Stroke per minute : 64,
Die Height : 1110 mm,
Slide adjustment : 10 mm,
Slide area (LR x FB) : 1520 x 1300 mm,
Die set (LR x FB) : 1650 x 1500 mm,
Side opening : 700 x 1200 x 1350 mm,
Upper ejector : 30 mm,
Lower ejector : 70 mm,
Main motor (KW x p) : 250 x 10,
Adjust motor (KW x p) : 150,
Working pressure (KG/cm2) : 6.
Induction Heater :-
Make : Myeongin Induction (Korea).
New in : November 2012.
Model : IHB102-152.
Capacitors : 1500 kW 1.0 kHz,
Input power : 6 P, 580 V, 60 Hz, 2000 KVA,
Control voltage : AC380V,
PLC type : XGT.
 
  70
IDMA27290
MakeErzhong
Model
YOM
ConditionBrand New
PhotoSee Photo
1) Press Hot Forging
Model : EXY125
Capacity : 12500 ton,
Slider Stroke : 520 mm,
Frequency of slider stroke : 30 s/min,
Effective stroke : 5 s/min,
Max shut height : : 2000 (-25) mm,
Adjustment value of slider : 25 mm,
Slider size :-
Length : 2190 mm,
Width : 2450 mm,
Worktable size :-
Length : 2240 mm,
Width : 3100 mm,
Side window dimension :-
Height : 1700 mm,
Width : 1300 mm,
Net width of the frame : 2300 mm,
Power of main motor : 530 kW, Rotation 750 rpm, 380V,
Upper ejector force : 600 kN,
Stroke : 40-120 mm,
Qty of upper ejector rod : 5x2,
Qty of bottom ejector rod : 5x2,
External dimension of the press :-
Length : 8330 mm,
Width : 8860 mm,
Height above ground : 10600 mm,
Air pressure : 0.55 Mpa,
Air consumption : 280 M/h,
Cooling water consunption : 25 M/h.
2) Press Trimming
Model : EQB12.5MN.
3) Press Trimming
Model : EQB12.5.
Rated pressure : 12.5 mn,
Slid block travel : 500 mm,
The distance between the slide block and the lover dead point under nominal pressure : 33 mm,
The frequency of the slide block continual travel : 26 min,
The maximum frequency of single travel : 12 times/min,
The maximum closing height : 1700 mm,
The slide block adjustable value : 200 mm,
Working table size :-
left-right : 2800 mm and backwards-forwards : 1400 mm,
Slide block face size :-
left-right : 2770 mm and backwards-forwards : 1400 mm,
Frame internal span : 2800 mm,
Lower ejector force : 500 kn,
travel : 200 mm,
Ejector arrangement : 2 locations determined by technical process,
Rising speed of the ejector cylinder : 100 mm,
Main motor : 112 kW,
Side window :- high 2000 mm and wide 500 mm,
External dimensions :- left-right 4140 mm and backwards-forwards 3350 mm,
Elevation above floor : 8000 mm,
Air consumption : 38 m3/h,
Cooling water consumption : 1.5 m3/h,
Machine Weight : 180000 kg.
The price for Bolsters (Die holder), dies, and etc. is not included in this quotation.
 
  71
IDMA27098
MakeTMP Voronezh Russia
Model
YOM
ConditionGood Condition
PhotoSee Photo
1) 2500 ton Press Hot Forging :-
Model : K8544
YOM : 1980
Capacity : 2500 ton,
Ram stroke : 350 mm,
Table dimensions :-
L to R : 1200 mm,
F to B : 1400 mm,
Continuous stroke per minute : 60 N°,
Single stroke per minute : 14 N°,
Connecting rod : 1 N°,
Die space : 890 mm,
Die Space adjustment in the table : 10 mm,
Space between uprights : 1320 mm,
Ram dimensions :-
L to R : 1070 mm,
F to B : 1120 mm,
Upright opening dimensions :-
Width :720 mm,
Height : 890 mm,
Upper knockout :-
Power 6 tn,
Stroke : 50 mm,
Pushers : 1 N°,
Lower knockout,
Power : 10 tn,
Stroke : 50 mm,
Pushers : 1 N°,
Main motor power : 132 kw,
Overall dimensions :-
L to R : 5350 mm,
F to B : 4680 mm,
Height above floor level : 6840 mm,
Press weight : 198 ton.
2) 250 ton Press Trimming :-
Model : KB9534
YOM : 1973
Capacity : 250 tons,
Ram stroke : 320 mm,
No. of strokes : 32 per min.,
Shut height : 390 mm,
Bolster plate-to-ram adjustment stroke : 140 mm,
Bed dimensions : 800 x 800 mm,
Bed opening dimensions : 500 x 500 mm,
Ram dimensions : 650 x 650 mm,
Bolster plate thickness : 140 mm,
Main drive motor power : 27 kW,
Overall dimensions : floor space 3260 x 2970 mm,
Height above floor level : 5180 mm,
Mass approx : 23.3 tons.
 
  72
IDMA26527
Make
Model
YOMOverhauled 2003
ConditionGood Condition
PhotoSee Photo
1) 4000 ton Forging Press :-
Maker : Smeral (Czech)
Model : LZK 4000A
Year : 1985 (Overhauled in 2003)
Capacity : 4000 ton,
Ram Stroke : 380 mm,
Number of Ram strokes : 60/min,
Width between uprights : 1580 mm,
Shut height : 1000 mm,
Ram Adjustment : 20 mm,
Table size : 1520 X 1600 mm,
Slide size : 1470 X 1400 mm,
Stroke of upper ejector : 50 mm,
Ejecting force of upper ejector : 105 KN,
Stroke of lower ejector : 80 mm,
Ejecting force of lower ejector : 140 KN,
Press Height above floor : 8100 mm,
Press dimension -
Hegith : 9150 mm,
Width : 4720 mm,
Length : 4640 mm,
Main drive motor output : 200 KW,
Press weight : 250 ton.
2) 400 ton Trimming Press :-
Maker : Voronezh (Russia)
Model : KB2536
Yom : Overhauled in 2003
Capacity : 400 tons,
Ram stroke : 250 mm,
Ram strokes : 25 min,
Shut height : 510 mm,
Bolster plate to ram adjustment stroke : 160 mm,
Bed dimensions : 1000 x 1000 mm,
Ram dimensions : 800 x 800 mm,
Bolster plate thickness : 160 mm,
Main drive motor power : 40 kW ,
Overall dimensions : 3410 x 3140 x 5940 mm,
Weight : 32.5 tons.
 
  73
IDMA26139
Make
Model
YOM1972
ConditionGood Condition
PhotoSee Photo
1) Press Hot Forging
Make : EUMUCO,
Model : SP400,
Capacity : 4000 ton,
Ram stroke : 350 mm,
No of Strokes min : 60,
Table Surface : 1360 x 1500 mm,
Ram Surface : 1220 x 1250 mm,
Die holder surface : 450 x 900 mm,
Distance table – ram : 1460 mm,
Stroke adjustment of the table : 25 mm,
The stroke of the lower extractor : 45 mm,
The stroke of the superior extractor : 32 mm,
Main motor power : 186 KW,
Overall size :-
Width : 4670 mm,
Length : 4235 mm,
Over ground height : 6555 mm,
Total height : 8190 mm,
Weight : 235 ton.
2) Press Trimming :
Make : MASSEY
Capacity : 400 ton.
Induction heating system.
 
  74
IDMA24248
MakeRussian
Model
YOM
Conditioncan be inspected under power
PhotoSee Photo
1. Press Hot Forging - model : KB8042
Rated capacity 1600 tn,
Slide stroke 300 mm,
Table adjustment 10 mm,
Strokes per min. in continuous 85 n°,
Single Stroke per min. 18 n°,
Dies 660 mm,
Bed Dimension 1050 x 1200 mm,
Slide dimension 860 x 910 mm,
Opening in upright 1080 mm, Overall dimensions 4850 x 3515 x5570 mm.
2. Russian Trimming Press 250 ton - K9534
250 tons, ram stroke 320 mm, no. of strokes 32 per min., shut height 390 mm, bolster plate-to-ram adjustment stroke 140 mm, bed dimensions 800 x 800 mm, bed opening diemensions 500 x 500 mm, ram diemensions 650 x 650 mm, bolster plate thickness 140 mm, main drive motor power 27 kW, overall dimensions: floor space 3260 x 2970 mm, height above floor level: 5180 mm, mass approx 23.3 tons .
3.Induction Furnace KW600
 
  75
IDMA20875
MakeMannesmann
Model
YOM1982
ConditionGood Condition
PhotoSee Photo
Hydraulic forging press “MEER HYDRAULIK” GLAMA ,1250/1600 ton; 320/ 400 bar, dia.1500 mm
Manipulator “GLAMA” 12,5 ton; 250 kNm,
Charger “GLAMA” 5,5 ton; 180 kNm.
 
  76
IDMA20734
Make
Model
YOM
Conditionexcellent working condition
PhotoSee Photo
Forging complex “TMP”, Voronezh, Russia with a 5 ton Hammer: 1) Hammer 17KP120 (similar as M2147)YOM 1972, 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons . 2) Open-type pre-forging 250 ton press . 3) Trimming press mod. K9536, 400 ton
 
  77
IDMA20566
Make
Model
YOM
ConditionGood working condition
PhotoSee Photo
Hot forging brass line:Forging line, cutting machine, SEO 3 press, trimming and blasting machine. Forging presses were produced by Mecolpress, one SOV2 (200 t) and SEO 3 (350 t). Both are equipped with generators, feeders, inductive heaters. SEO 3 is additionally equipped with automatic feeding arm and automatic conveyor for receiving the hot stampings.
(3) Gnutti Machines FMF12-125 type (12 spindles), blasting machine Schlick type : MB 2-5.2-1/7,5.

All machines were produced in 70s and early 80s. They were in usage till middle of December 2009.
 
  78
IDMA19204
MakeEumuco,Germany
Model
YOM1987
Conditionexcellent working condition
PhotoSee Photo
Billet Shear
- Year of Made : 1987
- Maker : Newellco
- Usage : Round Cut Material Heating
- Spec : Coil Ψ68
- Type : High Frequency Induction Heating Type
- Billet Transfer : Chain Connveror Moving
- 1st Transformer : 3,300V → 840V [1700kw]
- Billet Heater Consumption Electricity : 840V, 1,300kw

▪ 3,000 Ton Forging Press
- Installed ( Year of Made) : 1987 (1954)
- Maker : EUMUCO (Germany)
- Usage : Link Hot Forging
- Capa : 3,000 Ton
- Type : Mechanical Crank Type
- Weight of Equipment : 186 Ton
- Main Motor : 200kw x 440V x 6P
- Conveyor, etc : 10kw
▪ 3,000 Ton Automization Equip
- Newly Installed : 1990
- Maker : LAM BERTON
- Automatic Main Motor : 15kw (D.C Motor)
350 Ton Press
- Year of Made : 1996
- Maker : Dong-Shin, Korea
- Usage : Link Forged Product Punching & Trimming
- Type : H TYPE SINGLE CRANK
- Main Motor : 55kw x 440V x 4P
- Chip Conveyor, etc : 10kw

Heat Exchanger
- Year of Made : 1987
- Maker :
- Heat Exchanger Size :
- Feeding Size :
- Motor : 11kw x 440V x 4P
- Feeding Motor : 55kw x 440V x 4P
- Conveyor, etc : 2.2kw
Tempering Furnace
- Year of Made : 1987
- Maker : Young-Shin, Korea
- Tempering Heat Treatment of Link Forged Product
- Capa : 3,000 KG/HR
Type : Continuous MESH Conveyor Heat Air Circulation
- Dimension : 4,200W x 18,100L x 2,950H
- R/C FAN Driving Motor : 3 Set
(15kw, 11kw, 11kw x 440V x 4P)
- Blower Motor : 1 PCS
(11kw x 440V x 4P)
- Conveyor, etc : 10kw
Shot Blasting Machine
- Year of Made : 1987
- Maker : Korea Shot
- Surface Treatment of Link Forged Product
- Capa : Blasting Capa - 180 KG/min
- Continuous Belt Conveyor TYPE, Shot Ball
- Dimension : 2,852W x 5,400L x 5,690H
- Impellar Driving Motor : 2 PCS (12kw x 440V x 4P)
- Basket, Screw, Conveyor : 15kw

- Capa : 0.42m3/Charge Max.
- Capa Weight : 800kg/Charge Max
M.T Machine
- Year of Made : 1987
- Maker : Japan, Magnetic
- Inspect of Defected Surface of Forged product
- Capa : Magnetic Strength 10,000 ㎼/cm2
- Type : Black Light Magnet Inspect tupe
- Magnetic : 70kw (18~23V x 3000A)
- Conveyor, pump motor : 15kw

▪ M.T Step Feeder
- Year of Made : 1994
- Maker : Samwon ENG
- Main Driving Motor : 5.5kw x 440V x 4P
- Conveyor : 10kw
Electric Discharge Lathe
- Year of Made : 1990
- Maker : Dookwang Precision
- Klath the Mold Shape of Forged Link
- Spec : DK800SNC
- Max Moving Distance of Axle (X,Y,Z) : (1,000,400,600)
- Max Electricity : 300A
- Consumption of Electricity : 150kw
 
  79
IDMA10148
MakeRussian
Model
YOMBrand New
ConditionBrand New
PhotoSee Photo
Automated line with forging in one stroke of the press with the following scope of supply:

1.Varietal hydraulical shears for billets cutting of cpapacity 100t with set of shears for sticks -
2.Feeding tray
3.Billets loader .
4. 1000t crank forging press
5.Grip transfer.
6. Die block.
7.Separating tray
8. Conveyor for forgings.
9.Conveyor for punchings
10.System of technoligical lubrication "Acheson"
11.Programmer
 
  80
IDMA10031
MakeTMP Voronezh Russia
ModelKB8046
YOMBrand New
ConditionBrand New
PhotoSee Photo
KB8046 - 4000 tons, slide stroke 400 mm, number of slide strokes continous 50 /min, single 14/min , distance between table (intermediate plate installed on the table) and upper bolster plate of slide in its bottom position 1200 + 1,0 mm, adjustment value of distance between table and slide 10 + 0,2 mm, one position upper ejector : run value 40 mm, force 80tons, three position hydraulic lower ejector run value 80 + 2,0 mm , force 150 , 150 , 150 kN, table dimensions : left to right 1710 mm, front to back 1620 mm, slide dimensions left to right 1470 -1,0 mm, front to back 2000-1,0 mm, dimensions of openings in uprights :width 1040 + 2,0 mm, height 1300 + 2,0 mm, distance between uprights in light 1770 mm, Russian electric motor of main drive : power 160 kW, 975 RPM ,m Russian electric motor of adjustment mechanism drive : 4KW, 950 RPM, compressed air consumption per cycle 68,5, air pressure in pneumatic mains min 0,5(5,0) Mpa (kg/cm2) max 0,7(7,0) Mpa (kg/cm2), press overall dimensions 6790 + 50, front to back 5830 + 50 mm, press height 7850 + 80 mm, accuracy norms : planenness of table surface and lower surface of slide 0,08/1000mm no more, parreleism of table surface and lower surface of slide 0,2/1000 mm, perpendicularity of slide stroke to table surface 0,32 mm.
top