V. K. Engineering - Buying & Selling of Machines made easy

Category : Boring Mills

Sub-Category : Borer Horizontal Table Type CNC

Total Machines Found : 133

Select

| Machine Details

ID	MA38499
Make	Kuraki
Model	KBT13DX
YOM	1988
Condition	Good Condition
Photo	See Photo
SPINDLE SIZE:5.12 TABLE SIZE :63x70.8 MAX WEIGHT ON TABLE:22000 POUNDS X HORIZ TVL OF TABLE :118.11" Y VERT TVL OF HEAD :78.74" Z AXIS TRAVEL:51.18" W AXIS TRAVEL:27.56 RAPID TRAVERSE RATE (X/Y/Z):236IPM CUTTING FEDRATE:04-141.7IPM SPINDLE SPEED :5-1300RPM SPINDEL TAPER:CAT50 TOOL CHANGER CAPACITY:40 CNC COTROL: FANUC TABLE INDEX:0.001* INDEX INCREMENT:90* RETENTION STUD : MASP50T-1(45*) MAX TOOL DIA :4.921" MAX TOOL LENGTH:15.748

ID	MA38481
Make	Ceruti
Model	AD130
YOM	1998
Condition	Good Condition
Photo	See Photo
TABLE TRANSVERSAL TRAVEL (X) 2.500 MM. TABLE LONGITUDINAL TRAVEL (W) 3.000 MM. VERTICAL HEAD TRAVEL (Y) 2.250 MM. TABLE 2.200 x 1.800 MM. MAX. WEIGHT ON TABLE 15 TONS. SPINDLE  - ISO 50 130 MM. SPINDLE MOTOR POWER 37 KW. SPINDLE SPEEDS 1 � 1.000 RPM. CNC SELCA S 1200 TOTAL WEIGHT 40 TONS.

ID	MA38427
Make	Awea
Model	BL-2018
YOM	2012
Condition	Good Condition
Photo	See Photo
TRAVELS X-AXIS . 78.7" Y-AXIS . 70.8" Z-AXIS . 51.1" W-AXIS . 23.6" B-AXIS . 0.001 FULL FOURTH TABLE SIZE . 62.9" X 70.8" TABLE LOAD CAPACITY . 26,400 LBS. RAM SIZE . 18.9 x 18.9" SPINDLE MOTOR . 30 hp SPINDLE SPEED . 6,000 RPM SPINDLE TAPER . CAT-50 TOOL CHANGER CAP . 60 TOOL EQUIPPED WITH: FANUC 31I-MODEL B CNC CONTROL TOOL PROBE COOLANT THRU SPINDLE SPINDLE CHILLER CHIP CONVEYOR T-SLOTTED TABLE FULL ENCLOSURE

ID	MA38424
Make	Johnford
Model
YOM	2012
Condition	Good Condition
Photo	See Photo
Fanuc 31iMB Control Spindle Size 4.33" X-Horiz Tvl of Table 78.7" Y-Vert Tvl of Head 70.8" Power 35 hp RPM 3,000 RPM Table-W 62.99" Table-L 55.1" Spindle Tvl. 21.65" X Travel (in.) 79 Y Travel (in.) 71 Z Travel (in.) 63 W Travel (in.) 21.7 V Travel (in.) n/a Spindle Bar (in.) 4.33 Table Size (in.) 55 x 63 Max. Workpiece Load (lbs.) 26,400 Spindle (hp.) 35 Spindle (rpm) 3000 Spindle Speed Steps 2 Spindle Drive 2 Speed Gearbox RPM 3,000 ATC Capacity 60 (90/120/180 opt.) Weight (lbs.) 60,000� Equipped With Linear Scales XYZ Full �B� Axis Rotary Table with Scale 300 PSI Coolant through Spindle Chip Conveyor Spindle & Gearbox Cooler

ID	MA38418
Make	Kuraki,Japan
Model
YOM	2007
Condition	Good Condition
Photo	See Photo
Control Fanuc 16imb Table 950/1050 Table index 0.001 Spindle 110mm Travel 1500/1200/700 Spindle Quill 350 Atc -45

ID	MA38375
Make	Ikegai,Japan
Model	BX130P
YOM	1998 (2018 complete overhaul)
Condition	Good Condition
Photo	See Photo
Control： Fanuc Oi-MD Spindle Bore：130mm Spindle Speed：20-2000rpm Table Size：1400*1600mm Max Weight：6000kg X Travel： 2000mm Y Travel： 1600mm Z Travel：1500mm W Distance：700mm Table surface to spindle ：70~1670mm Table surface to spindle nose：700~2200mm ATC：60 magazine Taper ：BT50

ID	MA38327
Make	Femco
Model
YOM	1998
Condition	Good Condition
Photo	See Photo
Spindle Size: 4.3" Spindle Taper: ISO #50 X-Travel: 78.7" Y-Travel: 70.87" Z-travel: 66.93" W-travel: 19.69" Rotary Table width: 63" Rotary Table Length: 56.5" Power: 35 HP RPM: 2000 Fanuc 18M control Table Indexing (B axis): Full B Axis Rotary Table max weight: 14000 lbs Equipped With: 60 ATC Rigid Tapping Helical Interpolation Chip Conveyor Rotary table built in

ID	MA38321
Make	Sanco
Model	SHM-800L
YOM
Condition	Good Condition
Photo	See Photo
Size 800 x 800 (1000 x 800 )mm (1000 x 1000) T-Slots 22 x 7 mm Max. loading 3500 kg Height From ground 1170 mm Indexing Degree 1/350 sec Clamping force 6000 kg X- Axis Travel 1600 mm Y- Axis Travel 1200(1600) mm Z- Axis Travel 1000(1200) mm Spindle Nose to Table 225-1225 (225-1425 Spindle Center to Machine 0-1200(0-1600) mm Spindle Taper ISO 50, 7/24 mm Spindle Speed 2 Steps rpm 10-2500 (4000,6000) X/Y/Z Rapid Traverse 15/12/2015 M/min Cutting feed Rate 1-5000 mm/min East input 0.001 mm No.of tool 40(60/90/120) Tool Specification BT-50/P50 T-1 Max. Tool length 400 mm

ID	MA38320
Make	Femco
Model	BMC-110T
YOM
Condition	Good Condition
Photo	See Photo
Table Size 1440 x 1600 mm Travel X 2500 x Y 1800 x Z 1500 mm Travel W/(DIA) 500/ (110) Loading 8000 kg Max. W/P L x W x H 3000 x 2000 x 1800 mm Controller Fanuc 21 I - MB Spindle Speed (RPM) Min 5 Max 2500

ID	MA38251
Make	TOS
Model	WHQ105
YOM
Condition	Good Condition
Photo	See Photo
eidenhain TNC430M digital control Heidenhain measurement Siemens drives Max spindle revolutions 300min -1 Max power of main motor 28 kW Stroke 1800x1250x1250 W 630mm Table 1400x1400 BT50 All motors have been overhauled and B reducer housing Some tools provided

ID	MA38177
Make	Toshiba
Model	BP13B
YOM	1988
Condition	Good Condition
Photo	See Photo \| See Video
X4000mm Y2200mm Z1100mm �130mm W700mm Table (LW) : 40001500mm Rotary table : 2000*1800mm Fanuc 21i Controller changed 5 years ago

ID	MA38172
Make
Model	2A622F4
YOM	1987
Condition	Good Condition
Photo	See Photo
Table dimensions: 1250x1250 mm. Installed CNC � 2С42. Number of purchases: 7. Long spindle travel: 710 mm. Table movement: 1000 mm. Lateral movement: 1250 mm. Headstock movement (horizontal beam): 1000 mm. Spindle speed range: 6.3-2000 rpm. Maximum drill diameter size: 50 mm. Cutter diameter: 250 mm. Overall dimensions of the machine: 4140 x 6335 x 3980 mm. Machine weight: 20500 kg.

ID	MA38167
Make	Forest
Model	P125
YOM	1981
Condition	Good Condition
Photo	See Photo
SIZD : 1,250X1,600mm Xaxis : 2,000mm Yaxis : 1,600mm Zaxis : 800mm Waxis : 1,250mm

ID	MI10543
Make	Kuraki,Japan
Model	KBT11WDX
YOM
Condition	Good Condition
Photo	See Photo
CNC Control : Fanuc 15-M Spindle Size 4.33 in 109.98 mm Table Size 62.99 55.12"16001400 mm Max Table Load 14,300 lb (6486.37 kg) X Axis Travel 78.74 in (2000 mm) Y Axis Traveel :59.06 in (1500 .12 mm) Z axis Travel 57.09 in (1450 .09 mm) W Axis Travel (quill ) 25.9 in (649.99 mm) B Axis ( Table Indexing)0.001 Rapid Traverse Rate x/y/z/w 472/472/472/236 ipm Spindle Taper Cat 50 Spindle Speed 2500 rpm Spindle Motor 20 hp Coolant Thru Spindle Yes Equipperd WIth Fanuc 15 m Cnc COntrol Chip COnevyor

ID	MI10500
Make	Microcut
Model	HBM4
YOM	2010
Condition	Good Condition
Photo	See Photo
5 Axis CNC Table Type Boring Spindle ; 110mm Table size ; 1500mm x 1250mm Fanuc : 18i-MB Rotary table Indexing degree Degree 1 (std) / 0.001 (std) Table rotation speedrpm 5.5 (1�)/ 2 (0.001�) Max. table loading kg capacity : 10 Tons X axis table cross travel 2200mm Y axis headstock vertical : 1600mm Zaxis table long travel mm 1600mm W axis (quill) travel mm 550 Spindle power kW 15 / 18.5 (std) Max.spindle speed rpm 35-3000 Spindle torque Nm 740 / 863 (std) Spindle gear range 2 step (1:2/ 1:6) Rapid feed (XNIZ/W) m/min 12/12/12/6 Complete with Panel, pendant , chip conveyor , chiller , power pack, fully running & Manuals

ID	MA38097
Make	Microcut
Model	HBM4
YOM	2008
Condition	Good Condition
Photo	See Photo
XYZ W - 2.2 1.6 1.6 0.55 m Spindle speeds 3000 rpm Spindle taper ISO 50 B-axis rotary table (1deg.) 60 station arm ATC Right angled milling head Removal CNC facing head (U-axis) Spindle quill extension support

ID	MA38084
Make	TOS
Model	WHN13.8
YOM
Condition	Good Condition
Photo	See Photo
Control system Heidenhain . TNC 355 Diameter of working spindle . 130mm Travel X-axis . 3500mm Travel Y-axis . 2000mm Spindle speed . 0-1000/min. Spindle travel - W axis . 1000mm Travel Z-axis . 1500mm Spindle taper . ISO 50.

ID	MA38060
Make	Nomura
Model	HBM 110
YOM
Condition	Good Condition
Photo	See Photo
Table size 1400x1600 , 1875 up & down axis 2000 front & back axis 1400 left & right axis 500 w axis Fanuc OM control Total 2 unit

ID	MA38003
Make	TOS
Model	WHN110Q
YOM	2011
Condition	Good Condition
Photo	See Photo
Max. spindle speed - 2800 Max. main engine power CBT 37 vertical movement of the spindle head (Y-axis) MM 1250 transverse adjustment of the bed (Z axis) MM 1250 spindle extension (W axis) MM 710 table clamping surface 1250 x 1400 longitudinal table adjustment (X axis) MM 2000 design of the tool clamping shank in accordance with .DIN 69 871 TOS tool shank Varnsdorf control system SINUMERIK 840D measuring Heidenhain drives SIMODRIVE 611D � The following special accessories are supplied with the machine: core material KM 11/13 control and measuring probe RENISHAW RMP60 falling device CHOV 110 - 30 bar nsheiba LD650 grain head FEC 40

ID	MA37999
Make	Fermat
Model	WFT 13 CNC
YOM	2019
Condition	Good Condition
Photo	See Photo
Control system Heidenhain . TNC 640 Diameter of working spindle . 130mm Travel X-axis . 3500mm Travel Y-axis . 2500mm Spindle speed . 10-3000/min. Pressure of cooling . 20bar Spindle travel - W axis . 730mm Travel Z-axis . 1500mm Spindle taper . SK 50. Table dimensions . 1800 x 2200mm

ID	MA37993
Make	Femco
Model
YOM	2006
Condition	Good Condition
Photo	See Photo
Spindle Size: 4.3" Spindle Taper: ISO #50 X-Travel: 78.7" Y-Travel: 70.87" Z-travel: 66.93" W-travel: 19.69" Rotary Table width: 63" Rotary Table Length: 56.5" Power: 35 HP RPM: 2500 Coolant Thru Spindle: yes Fanuc 21iMB control Table Indexing (B axis): Full B Axis Rotary Table max weight: 14000 lbs Equipped With: 60 ATC Rigid Tapping Helical Interpolation Chip Conveyor Rotary table built in

ID	MI10411
Make	Toshiba
Model	BP-130R22
YOM	2003
Condition	Good Condition
Photo	See Photo
Pallet Size: 1800 mm X 2200 mm (Dual Pallet) Travels: X: 4000 mm; Y:2350 mm; Z: 1500 mm; W: 800 mm Milling Spindle Extension: 200 mm, Spindle Speed: 5 to 2500-RPM, BT50 Spindle Taper, BIG-PLUS Spindle System, Chip Conveyor, Through Spindle Coolant

ID	MI10409
Make	Johnford
Model	BMC-4000
YOM	2008 / 07
Condition	Good Condition
Photo	See Photo
Table Size : X Axis travels -4000 MM Y Axis travels -1800 MM Z Axis Travels -1600 MM Spindle Speed -10 to 8000 RPM Spindle nose -BT- 50 No of Tools in ATC Table Indexing 60 Table Indexing 0.0001 Degree Distance from Spindle to Table -700 to 2300 mm

ID	MA37964
Make	Kuraki,Japan
Model	KBH-12
YOM	2007
Condition	Good Condition
Photo	See Photo
FANUC16i-MB BT50 ATC30 pieces Table size 1000�1200 Spindle rotation speed 12000rpm Stroke X1500 Y1200 Z900 W400 Rotating spindle diameter 200 Arbitrary indexing center Through (3Mpa) Chip conveyor with tool length measurement

ID	MA37947
Make	Pama Italy
Model
YOM	2014
Condition	Good Condition
Photo	See Photo
FANUC 31 i M CNC Controls PAMA 5000 mm x 5000 mm Infeeding Rotary Table CAPACITY: Spindle Diameter - 203 mm Spindle Taper ISO #50/60 (Big Plus) Vertical Travel of Head, Y-Axis - 6,000 mm Column Travel, X-Axis - 16,000 mm Ram Travel, Z-Axis - 1,330 mm Spindle Travel, W-Axis - 830 mm Total Axial Travel, Ram & Spindle - 2,160 mm Ram Cross Section - 530 mm x 600 mm Spindle Speeds: - 1-680 RPM PAMA CNC Infeeding B-Axis ROTARY TABLE: Table Size - 5,000 mm x 5,000 mm Table Infeed, V-Axis - 2,500 mm Table Rotation - 360,000 Position Table Weight Capacity -120 Tons EQUIPPED WITH: FANUC 31 i M CNC Controls Chip Conveyor T-Slotted Floor Plate 4,000 mm x 2,000 mm (10 EA) 75 HP Spindle Motor

ID	MA37913
Make	Union
Model	BFT130/8
YOM	1998
Condition	Good Condition
Photo	See Photo \| See Video
X-Axis - 2750 mm Y-Axis - 2500 mm Z-Axis - 2320 mm W-Axis - 700 mm spindel power - 50 kW spindel speed - 1,6 � 1.600 rpm tool holder - SK 50 Control: CNC HEIDENHAIN TNC426 Tabel dimension - 2000 x 1800 mm max. Tabel load - 8 ton B-Axis - 360 � Division - 0,001° Weight - 37000 kg

ID	MA37910
Make	OKK
Model	MCH1000
YOM
Condition	Good Condition
Photo	See Photo
Table size 1,000X1,000mm Spindle 130

ID	MA37907
Make	WMW Heckert ,Germany
Model	BFT 110/6
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter: 110 mm X-travel: 1950 mm Y-travel: 1600 mm Z-travel: 2000 mm Table size: 1400x1600 mm Table rotation: 360 degrees Max. work-piece weight: 8000 kg Spindle speeds range: 5.6 - 1120 rpm Tool taper: ISO 50 Quill Stroke: 800 mm Main motor power: 40 kW Dimensions: 7000x4700x4400 mm Machine weight: 26700 kg

ID	MA37869
Make	WOTAN
Model	B130P
YOM	1992
Condition	Good Condition
Photo	See Photo
Control system Siemens Sinumerik 850 Diameter of working spindle 130 mm Table dimensions 3000x2800 mm Travel X-axis 5000 mm Travel Y-axis 2500 mm Travel Z-axis 900 mm Main motor power 23 kW Machine weight 30000 kg The machine is in good condition, functional. Not possible to test, disconnected. - Numerical control SIMENS 850 CNC - Column height 390 cm - bed plate width 140 cm - bed length 600 cm Table type S35C

ID	MA37802
Make	TOS
Model
YOM
Condition	Good Condition
Photo	See Photo
X 3500 Height 2000 Table 2000x 1800 With Atc 60 Tool

ID	MA37791
Make	Pama Italy
Model
YOM
Condition	Good Condition
Photo	See Photo \| See Video
Spindel - 180 mm X 8000 Y 3200 Z 1500 ZC 850 Rotary table 2200x3000 Control CNC Heidenhain ITNC520

ID	MI10166
Make	Castel
Model	Matic 2
YOM
Condition	Good Condition
Photo	See Photo
Spindle Diameter: 100 mm Spindle Taper: BT50 Maximum Spindle rpm: 2400 (Low Gear: 500 / High Gear 2400) Table Size: 1250 mm X 1000 mm Travels: X: 1500 mm Y: 1200 mm Z: 1000 mm W: 500 mm B: 0.001� Index CNC Control: Fanuc OiMF Plus (New)

ID	MA37615
Make	TOS Varnsdorf
Model	WH10
YOM
Condition	Good Condition
Photo	See Photo
Control system Heidenhain . TNC 426 Diameter of working spindle . 100 mm Travel X-axis . 1250 mm Travel Y-axis . 1120 mm Spindle speed . 10 - 1800 /min. Spindle travel - W axis . 630 mm Travel Z-axis . 940 mm Spindle taper . ISO 50 . Clamping area of table . 1000 x 1120 mm Max. load of table . 3000 kg

ID	MA37614
Make	TOS Varnsdorf
Model	WH 10NV
YOM	1991
Condition	Good Condition
Photo	See Photo
Control: NC -Table adjustment travel x / y-axis = 1250 /1000mm Operation via control panel Equipment: Length measuring system Heidenhain, transformer, hydraulic unit and control stand Accessories: - Various tool holders SK 50, collet chucks, collets, boring bars etc. In Leipzig we constantly offer over 700 machines and more than 10,000 operating articles on about 25,000m2 storage space. We are also specialized in retrofit and service for your machine tools. Our crane capacity:up to 64t. boring spindle diameter 100 mm x-axis 1250 mm y-axis 1100 mm z-axis 950 mm quill stroke 630 mm control Heidenhain TNC 135 (Strecke) number of spindle speeds min./max.: 8 - 1250 / 9 step U/min U/min. feed speeds 4 - 2500 mm/min mm/min tool taper ISO 50 table surface area 1120 x 1000 mm table rotating 360 Grad table load 3,0 t total power requirement 50,0 kVA kW weight of the machine ca. 13,4 t dimension machine approx.LxWxH 4,9 x 3,4 x 3 ,6 m dimensions electric cabinet LxWxH 2,0 x 0,65 x 2,4 m dimensions of hydaulic 600 x 575 mm

ID	MA37613
Make	TOS Varnsdorf
Model	WH10
YOM	1999
Condition	Good Condition
Photo	See Photo
Control Heidenhain TNC 410. After general repair in 1999. Spindle diameter 100 mm Spindle ISO 50 Spindle revolutions 900 rpm Table 1000 x 1000 mm Table loading 3000 kg 3yrbbyq3 X axe 1200 mm Z axe 800 mm Y axe 1000 mm W axe 630 mm Machine weight 13.400 kg

ID	MA37612
Make	Union
Model	BFT 110/6
YOM	2001
Condition	Good Condition
Photo	See Photo
Horizontal - 3 Axis X-Travel 2000 mm Y-Travel 1600 mm Z-Travel 2000 mm Machine length 6950 mm Machine width 4685 mm Machine Height 3885 mm Table Height 1050 mm Spindle Diameter 110 mm Spindle Taper ISO 50 Table Dimensions (Lengthxwidth) 1400 x 1600 mm Faceplate speed 5,6 - 224 RPM Spindle Speed 5,6 - 1120 RPM Metric thread feeds 1,25 - 56 mm Drive Capacity - Spindle Motor 40 kW Weight Of The Machine Ca. 25 t Bore Depth W 800 mm Type of control CNC Control Heidenhain-Steuerung TNC 310

ID	MA37564
Make	Sanco
Model	SHM-800L
YOM	2010
Condition	Good Condition
Photo	See Photo
CNC Horizontal Boring and Milling Machine CT4210 Fanuc Series 21i-MB

ID	MI9962
Make	Pegard
Model
YOM
Condition	Good Condition
Photo	See Photo
Spindle Dia -100 mm X-Travel -1500 mm Y-Travel -1000 mm Z-Travel -1500 mm Table -1200 X 900 mm With Spindle Support and all tools Fanuc OiMF control

ID	MA37454
Make	TOS
Model
YOM
Condition	Good Condition
Photo	See Photo
Diameter of working spindle . 130mm Travel X-axis . 3500mm Travel Y-axis . 2000mm Spindle speed . 0-800/min. Spindle travel - W axis . 800mm Travel Z-axis . 1250mm Spindle taper . ISO 50. Clamping area of table . 1800x1600mm Max. weight of workpiece . 12000kg Main motor power . 37kW Machine dimensions l x w x h . 7200x7800x4900mm The electrical box has been renewed

ID	MA37428
Make	Union
Model	KC150
YOM	2004
Condition	Good Condition
Photo	See Photo
Heidenhain iTNC 530 CNC Control. 120 ATC. New 2004 Spindle Speed: 3000 Rpm 2 gear ranges 150mm spindle diameter. Tool Changer: 120 Tools Cat 50 Taper Travels: X Axis 3200 mm Y Axis 2500 mm Z Axis 1500mm W Axis(Quill) 750mm.

ID	MI9796
Make	San Rocco
Model	140
YOM
Condition	Good Condition
Photo	See Photo
Spindle .140 Travel : 3000x1750xh1750 mm Spindle travel : 1000 mm Table : 2000x1520 mm Cnc Heidenhein.530

ID	MA37332
Make	Kuraki,Japan
Model	KBT-11WDX
YOM	1995
Condition	Good Condition
Photo	See Photo
CNC Control yes Type of CNC Control Fanuc 15-M Spindle Size 4.33 in 109.98 mm Table Size 62.99" x 55.12" 62.99" x 55.12" Max Table Load 14300 lb 6,486.37 kg X Axis Travel 78.74 in 2,000.00 mm Y Axis Travel 59.06 in 1,500.12 mm Z Axis Travel 57.09 in 1,450.09 mm W-Axis Travel (Quill) 25.59 in 649.99 mm B-Axis (Pallet Indexing) 0.001� Rapid Traverse Rate (X/Y/Z/W) 472/472/472/236 ipm Spindle Taper CAT 50 Spindle Speed 2,500 rpm Spindle Motor 20 hp Coolant Thru Spindle yes EQUIPPED WITH - Fanuc 15-M CNC Control

ID	MA37317
Make	Nomura
Model
YOM	1989
Condition	Good Condition
Photo	See Photo
5-Axis Ready, HBM & New Spindle Chiller Table Size: 79″ x 71″ Travels: X-Axis: 94" Y-Axis: 85" Z-Axis: 57" W-Axis: 36" B-Axis: Yes Spindle Size: 6″ Spindle Taper: 50 Taper (Jaw Bar-Retention Knobs) Spindle Speed: 1,500 RPM Motor: 15 hp Max. Table Load: 10,000 Lbs. (Approx.) Dimensions: 256″ L x 223″ W x 191″ H (Approx.) Weight: 58,000 Lbs. (Approx.) Equipped with: Fanuc OM Control 5-Axis (Shop ran it has a 3-Axis) Rotary Table Included New Spindle Chiller ($8K Value) New Draw Bars Spindle Drive � Updated 10 yrs Ago & all Drives rebuilt. Includes Spare Parts � Brand New Drives for X & Y.

ID	MA37034
Make
Model	WFC 10 CNC
YOM	2012
Condition	Good Condition
Photo	See Photo
Control system Heidenhain TNC 620 Diameter of working spindle 100 mm Travel X-axis 2000 mm Travel Y-axis 1250 mm Spindle speed 10 - 3000 /min. Cooling through spindle YES Pressure of cooling 20 bar Spindle travel - W axis 730 mm Travel Z-axis 1250 mm Tool magazine NO Spindle taper ISO 50 . Table dimensions 1250x1400 mm Max. load of table 3000 kg Machine weight 22200 kg Machine dimensions l x w x h 5470x5900x3200 mm

ID	MA37032
Make	TOS Varnsdorf
Model	WH 105 CNC
YOM	2009
Condition	Good Condition
Photo	See Photo
Control system Heidenhain TNC 530 Diameter of working spindle 105 mm Travel X-axis 1800 mm Travel Y-axis 1600 mm Spindle speed 0 - 3300 /min. Cooling through spindle NO Spindle travel - W axis 630 mm Travel Z-axis 1250 mm Tool magazine NO Spindle taper ISO 50 . Max. load of table 4000 kg Dimensions of table working surface 1400x1600 mm Main motor power 28 kW Machine dimensions l x w x h 6200xx4700x4150 mm Machine weight 15000 kg

ID	MA37030
Make
Model	WFT 11 CNC
YOM	2017
Condition	Good Condition
Photo	See Photo
Control system Heidenhain TNC 530 Diameter of working spindle 110 mm Travel X-axis 3000 mm Travel Y-axis 2000 mm Spindle speed 10 - 3000 /min. Cooling through spindle YES Pressure of cooling 20 bar Spindle travel - W axis 730 mm Travel Z-axis 1250 mm Tool magazine YES Number of positions in magazine 32 Spindle taper ISO 50 . Table dimensions 1400x1600 mm Max. load of table 8000 kg Main motor power 19,5 / 29 kW Machine weight 24900 kg Machine dimensions l x w x h 5600x6200x4400 mm

ID	MA36938
Make	Femco
Model	BMC110R2
YOM	2005
Condition	Good Condition
Photo	See Photo \| See Video
Control Type Fanuc 21i-MB Spindle Size 4.3" Table Size 63" x 56.5 Max Weight On Table 14,000 pounds B-Axis (Pallet Indexing) 0.001� X-Horiz Tvl of Table 78" Y-Vert Tvl of Head 70" Z-Axis Travel 67" W-Axis Travel (Quill) 20" Spindle Taper CAT 50 Spindle Speed 2,500 Spindle Motor 35 Tool Changer Capacity 32 Dimensions 258" x 215" x 146" Weight 42,000 pounds Equipped With Fanuc 21i CNC Control Rotary Table with full B-Axis 32 Position Automatic Tool Changer (Angle plates not included)

ID	MI9337
Make
Model
YOM
Condition
Photo	See Photo
75 mm spindle

ID	MA36805
Make	Tos Czech
Model	WHN13
YOM	1987
Condition	Good Condition
Photo	See Photo
Spindle dia. 130 mm Spindle taper ISO 50 Table size 1800 x 1600 mm Cross movement 3500 mm Length movement 2000 mm Vertical movement 2000 mm Spindle quill 800 mm Spindle speeds 5,6-710 rpm Table load 12 ton Control: Heidenhain TNC 355

ID	MA36527
Make	Doosan
Model	DBC130L
YOM	2012
Condition	Good Condition
Photo	See Photo
X4000, Y2500 Table : 1800 x 2000 ATC : 40 Index angle : 0.001 degree Coolant throw spindle Fanuc 31iMB

ID	MA36526
Make	Doosan
Model	DBC130L
YOM	2011
Condition	Good Condition
Photo	See Photo
X4000, Y2500 Spindle diameter : 130 mm Spindle speed : 3000 rpm W-axis : 700 mm Z-axis : 1600 mm Table : 2200 x 2000 mm Table load : 13 ton Chip conveyor Index angle : 0.001 degree Coolant throw spindle Fanuc 31iMB ATC : 60

ID	MI8888
Make	TOS
Model
YOM
Condition	Good Condition
Photo	See Photo
X3500 y2000. W1500 Z 1000

ID	MI8745
Make	Ceruti
Model
YOM
Condition	Good Condition
Photo	See Photo
X : 1320mm Y : 930mm Z : 900mm W : 300mm B : 989mm 1 : 2.75 Fanuc OIMD Control

ID	MA36353
Make	WMW Union
Model	BFT110
YOM	1989
Condition	Good Condition
Photo	See Photo
Spindle dia. 110 mm Spindle taper ISO 50 Table size 1600 x 1400 mm Cross movement (X) 1985 mm Length movement (Z) 1960 mm Vertical movement (Y) 1620 mm Spindle movement 710 mm Spindle speeds 6,3 - 1250 rpm Facing head dia 700 mm Facing head movement 250 mm Facing head speed 6,3 - 315 rpm Table load 6300 kg Motor power 90 Kw Control: Heidenhain TNC 355

ID	MA36176
Make	San Rocco
Model
YOM
Condition	Good Condition
Photo	See Photo
San Rocco.100 Spindle .100 Travel : 1800x 1200x 1500 mm Cnc Selca

ID	MA36175
Make	Castel
Model
YOM
Condition	Good Condition
Photo	See Photo
Spindle .100 Travel 1500x 1000x1200 mm Rotary table 4 position ,

ID	MA36082
Make	SKODA
Model	W160
YOM
Condition	Good Condition
Photo	See Photo \| See Video
Spindle dia 160 mm X 4150 mm Y 5000 mm W 1300 mm Machine weight aprox. 55000 kg Table SKODA E20 � 2500 x 2000 mm load capacity 20000 kg 1 x Milling head 5 x Milling cutters Digital readout 4150 x 5000 � incl. rotary table SKODA E20 + milling head + DRO + 5 milling cutters

ID	MI8259
Make	Kuraki,Japan
Model	KBT11DXACNC
YOM
Condition	Good Condition
Photo	See Photo
Fanuc Series11-MB CNC Control 40-Position Automatic Tool Changer YOM:-1986(Retrofitted/Overhauled in 2003) CAPACITY: Spindle Diameter -110 Taper In Spindle � BT 50 Vertical Head Travel, Y-Axis -1250 Table Cross Travel, X-Axis -1700 Column Travel, W-Axis -650 Spindle Travel, Z-Axis -1150 Table Size, Built-In Rotary -1200 x 1400 Table Rotation, B-Axis -360,000 Positions Table Load Capacity -4,000Kgs Spindle Speeds-5-2000 RPM Spindle Motor -40 HP Rapid Traverse, X, Y, Z-Axis -394 IPM Manuals Available. Running Video available. EQUIPPED WITH: Fanuc 11 -MB CNC Control 40 Station Automatic Tool Changer Remote Pendant Built-In 360,000 Full Contouring Rotary Table Ballscrews & Independent AC Servo Drives Hardened & Ground Box Ways on All Slide-Ways Partial Chip Enclosure Steel Telescoping Way Covers Chip Conveyor System

ID	MA35805
Make	LX20TL3
Model	WH105
YOM	2008
Condition	Good Condition
Photo	See Photo
CNC HEIDENHAIN iTNC 530 M Table dimensions (useful): 1400 x 1400 mm Diameter of the working spindle: 105 mm Taper ISO 50 X-axis travel: 1800 mm Y-axis travel: 1250 mm Z-axis travel: 1250 mm Shaft travel on W-axis: 630 mm B-axis: 360� Motor power: 28 kW Working spindle speed: 3300 Rpm Working speeds of the groups on the X, Y, Z, W axes 5 m/min Rapid feeds of the X, Y, Z axes 10 m/min Rapid displacement of the W-axis, 8 m/min Rapid displacement of the B-axis, 720�/min Maximum weight of the working piece: 5000 kg Lot of accessories included

ID	MA35743
Make	TOS
Model	WH10NC
YOM	1989
Condition	Good Condition
Photo	See Photo
Spindle diameter: 100 mm Spindle attachment: ISO 50 with automatic tool clamping Spindle speed: 16-1250 rpm Spindle power: 20 kW Table size: 1120x1000 mm Table load: 3000 kg Longitudinal/cross/vertical/spindle: 1000/1250/1120/630 mm Machine weight: 13400 kg Machine can be used conventionally with hand wheels without control! Accessories: 1 Universal milling head, type: UFP 40 ISO 40 1 Spindle guide sleeve 10 Tool holders ISO 50 1 Spare control HEIDENHAIN, type: TNC 135 with monitor 1 Program recording device HEIDENHAIN, type: ME 101 1 Machine light 1 Cooling system Ball screws Instruction manuals Control: HEIDENHAIN TNC 135 for 3 axes

ID	MA35645
Make	LX20TL3
Model	WHN13.8
YOM	1996
Condition	Good Condition
Photo	See Photo
TRANSVERSAL TABLE TRAVEL (X) 3.500 MM. LONGITUDINAL COLUMN TRAVEL (W) 1.250 MM. VERTICAL HEAD TRAVEL (Y) 2.000 MM. TABLE 1.800 x 1.600 MM. MAX. WEIGHT ON TABLE 12 TONS. SPINDLE STROKE (Z) 800 MM. SPINDLE  130 MM. SPINDLE TAPER ISO 50 SPINDLE SPEEDS 5 � 1.500 RPM. SPINDLE MOTOR POWER 37 KW. WORKING FEEDS (X; Y; W; Z) 4 � 3.000 MM/MIN. RAPID FEEDS (X; Y; W; Z) 8.000 MM/MIN. TOTAL WEIGHT 35 TONS. CNC HEIDENHAIN TNC 426 - 5 AXIS COMPLETE WITH: - VERTICAL MILLING HEAD - BORING SUPPORT - CHIPCONVEYOR

ID	MA35644
Make	Tos Czech
Model	WHQ13
YOM
Condition	Good Condition
Photo	See Photo
Spindle: mm.130 Spindle taper: ISO.50 Table cross travel X:mm.3500 Head vert.travel Y:mm.2500 Spindle travel Z: mm.800 Upright long.travel W:mm.1250 Table :mm.1800x2200 Table max.load admitted:KG.12000 Table rapid feed of B axis: �/min.540� Table axis indexed 0,001�: Pos/deg.360000 Spindle speed: RPM.1600, 37 kW (not data) Milling head Machine weight:Kg. 40000 CNC Heidenhain TNC 426

ID	MA35598
Make	Giddings & Lewis
Model	G60T
YOM	1980
Condition	Good Condition
Photo	See Photo
FEATURES : GIDDINGS & LEWIS 800M CNC CONTROLS CAPACITY: SPINDLE DIAMETER - GIDDINGS & LEWIS 800M CNC CONTROLS CAPACITY: SPINDLE DIAMETER - 152 MM TAPER IN SPINDLE - #50 VERTICAL TRAVEL, Y-AXIS - 3048 MM CROSS TRAVEL, X-AXIS - 4267 MM SADDLE TRAVEL, W-AXIS - 1600 MM SPINDLE TRAVEL, Z-AXIS - 1219 MM SPINDLE SPEEDS (INF VARIABLE) - 5-1120 RPM TABLE SIZE - 1829 MM X 4267 MM EQUIPPED WITH: G & L 800M CNC CONTROL POWER DRAW BAR HARDENED WAYS ON BED & SADDLE BALL SCREWS AND INDEPENDENT SERVO DRIVES OUTRIGGER TABLE SUPPORTS (6) 3-WAY VERTICAL COLUMN 40 HP DC SPINDLE DRIVE

ID	MA35591
Make	TOS
Model	WHQ13.8
YOM	1996
Condition	Good Condition
Photo	See Photo
Specifications: spindle 130mm Taper ISO 50 1600RPM / 37 KW STROKE X 3500 STROKE Y 2500 STROKE Z 1250 STROKE W 800 ROTARY TABLE 1800 X 2000mm B - 0.001� - 360� Max. Load 12000 kg ATC 60 POS spindle support sleeve Machine weight: ca. 40 tons

ID	MA35561
Make	Giddings & Lewis
Model	G60T
YOM	2005
Condition	Good Condition
Photo	See Photo
FEATURES: FAGOR 8055I CNC CONTROL (RETROFIT 2005) SPECIFICATIONS: SPINDLE DIAMETER: 152 MM SPINDLE TAPER: #50 ISO VERTICAL HEAD TRAVEL, Y-AXIS: 2743 MM TABLE CROSS TRAVEL, X-AXIS: 4267 MM SADDLE TRAVEL, W-AXIS: 1600 MM SPINDLE TRAVEL, Z-AXIS: 914 MM TABLE SIZE: 1829 MM X 4267 MM TABLE WEIGHT CAPACITY: 60,000 LBS SPINDLE SPEEDS, VARIABLE 4-RANGES: 10-1140 RPM EQUIPPED WITH: FAGOR 8055I CNC CONTROL (NEW 2005) TELESCOPING STEEL WAY COVERS ON BED AND SADDLE BALLSCREWS AND INDEPENDENT DRIVES TELESCOPING STEEL WAY COVERS ON X-AXIS 40 HP SPINDLE DRIVE LOADING: OFFER INCLUDES DISASSEMBLY & LOADING TO TRUCKS

ID	MA35545
Make	LX20TL3
Model	WHN13CNC
YOM	1996
Condition	Good Condition
Photo	See Photo \| See Video
T type borer TRANSVERSAL TABLE TRAVEL (X) 3.500 MM. LONGITUDINAL COLUMN TRAVEL (W) 1.250 MM. VERTICAL HEAD TRAVEL (Y) 2.000 MM. TABLE 1.800 x 1.600 MM. MAX. WEIGHT ON TABLE 12 TONS. SPINDLE STROKE (Z) 800 MM. SPINDLE  130 MM. SPINDLE TAPER ISO 50 SPINDLE SPEEDS 5 � 1.500 RPM. SPINDLE MOTOR POWER 37 KW. WORKING FEEDS (X; Y; W; Z) 4 � 3.000 MM/MIN. RAPID FEEDS (X; Y; W; Z) 8.000 MM/MIN. TOTAL WEIGHT 35 TONS. CNC HEIDENHAIN TNC 426 - 5 AXIS COMPLETE WITH: - VERTICAL MILLING HEAD - BORING SUPPORT - CHIPCONVEYOR

ID	MA35543
Make	Tos Czech
Model	WHN13.4
YOM
Condition	Good Condition
Photo	See Photo
Spindle dia: 130 mm X travel - 2000mm Y travel - 2000mm Z travel - 800mm

ID	MA35542
Make	LX20TL3
Model	WHN13.8
YOM	1985 full retrofit 2000
Condition	Good Condition
Photo	See Photo
Spindle dia. 130 mm Table area 2200 x 1800 mm X:3500 mm Y:2000 mm W:800 mm Z:1250 mm Control: cnc haidenhain 426

ID	MA35235
Make	Tos Czech
Model	WHN13CNC
YOM	Total overhaul 2003
Condition	Good Condition
Photo	See Photo
With control system MEFI CNC 8 x 9 - X = 3500 mm - Y = 2000 mm - Z = 1250 mm W = 800 mm Table : 1600 x 1800 mm ISO 50

ID	MA35117
Make	Doosan
Model	DBC130LII
YOM	2014
Condition	Good Condition
Photo	See Photo
TRAVELS X Axis : 4,000 mm Y Axis : 2,500 mm Z Axis : 2,000 mm W Axis : 700 mm Table size : 1,600*1,800 mm TSC 20 BAR TABLE DEGREES (0.001) NEW BT50 TOOLS 20EA Spindle rpm:3,000 Spindle 2 step gear type Tool taper:BT50 Magazine capacity : 40ea LINEAR SCALE (X, Y, Z, B Axis) Controller : FANUC-31i 220V, 60Hz BOX Guideway type Chip conveyer, Chip bucket Oil skimmer Call right(LED 3 Step) MPG handle Manual books

ID	MA35103
Make	Tos Czech
Model	WHN13.4C
YOM	1989
Condition	Very good condition
Photo	See Photo \| See Video
Spindle dia. 130 mm Spindle taper ISO 50 Table area 1600 x 1800 mm X 2000 mm Y 2000 mm W 1250 mm Max. workpiece weight 12000 kg Machine weight 32000 kg

ID	MA35063
Make	Sacem
Model	ST110
YOM	1979 Revised in 2000
Condition	Good Condition
Photo	See Photo
Spindle diameter: 110mm x-travel 1700 mm y-travel 1200 mm- z-travel 1250 mm tool holder SK 50 Table size: 1,200 x 1,450mm Drive power: 13.4kW Dimensions machine: 4.8 x 3.7 x 3.2m Dimensions control cabinet: 2.4 x 0.7 x 1.8m Machine weight : approx. 12.5 tons Control Heidenhain TNC 125- separate display for the W-axis

ID	MA35016
Make	LX20TL3
Model	WHQ13
YOM	2005
Condition	Good Condition
Photo	See Photo
Heidenhain 530 X/Y: 3500/2500 mm Table: 2250x1800 mm

ID	MA34714
Make	WMW Union ,Germany
Model	BFT130/6
YOM	1983
Condition	Good Condition
Photo	See Photo
Description Table size 2000 x 1800 mm Spindle diameter 130 mm Spindle taper ISO 50 Spindle speeds Cross movement (X) - 2740 mm Longitudinal movement (Z) - 2435 mm Vertical movement (Y) - 2500 mm Spindle drill movement (W) - 1000 mm Rotary table movement 360 deg. (through the E431468 control) Control: Mitsubishi Meldas 520 AMH Equipped with: 30 pcs. tool holders Additionally Extra rotary table

ID	MA34610
Make	Toshiba Japan
Model
YOM	1992
Condition	Good Condition
Photo	See Photo
Control : Tosnuc 777 Totary Table : 1800mm X 2200mm Table rotation : 0.001 degree Loading capacity : 10ton Stroke : X 3000mm, Y 2300mm, Z 1600mm, W 700mm Spindle diameter : 130mm Spindle RPM : 2500rpm ATC : 38ea

ID	MI7723
Make	WMW Union ,Germany
Model
YOM
Condition	Good Condition
Photo	See Photo
CNC Controller : siemens 828D with 1 year warranty x axis : 1600mm y axis : 1250mm z axis : 900mm B axis : (Rotary table)0.001 deg index -able (its NC Rotary table) Feed rate : (X/Y/Z)0.001-5m/min Rapid traverse : (X/Y/Z) 10m/min Spindle: Tool holder : SK50 Speed range : 50-3600rpm spindle orientation through encoder Spindle motor : 36kw ATC No of tools : 60 Tool holder : SK50 Tool changer ARM type Tool Magazine Through Gear box driven Through VFD Pallet Changer Number of pallets : 2 Pallet Dimension : 1000mm x 1000mm Max. table load : 2000kg Pallet changer through motors with chain driven Coolant System Coolant tank along with pump Space requirement (LxwxH): 8 x 6 x 4 m

ID	MA34424
Make	Giddings & Lewis
Model	H60-TX
YOM	1992
Condition	Good Condition
Photo	See Photo
G & L 8000B CNC CONTROL 80-STATION AUTOMATIC TOOL CHANGER 3-WAY VERTICAL COLUMN THRU SPINDLE & FLOOD COOLANT SYSTEM PREPARED FOR B-AXIS ROTARY TABLE AIR BLAST HANSON OIL CHILLER HARDENED & GROUND BOX WAYS ON X & W AXIS CHIP CONVEYOR CAPACITY: SPINDLE DIAMETER:152 MM TAPER IN SPINDLE:CAT 50 VERTICAL TRAVEL OF HEAD, Y-AXIS:3658 MM CROSS TRAVEL OF TABLE, X-AXIS:4267 MM SPINDLE TRAVEL, Z-AXIS:1524 MM SADDLE TRAVEL, W-AXIS:2438 MM TABLE SIZE:1829 MM X 4267 MM TABLE LOAD CAPACITY:80,000 LBS. SPINDLE SPEEDS:9-2200 RPM SPINDLE MOTOR:75 HP POWER REQUIREMENTS:460/3/60 EQUIPPED WITH: G & L 8000B CNC CONTROL 80-STATION AUTOMATIC TOOL CHANGER 3-WAY VERTICAL COLUMN THRU SPINDLE & FLOOD COOLANT SYSTEM AIR BLAST HANSON OIL CHILLER HARDENED & GROUND BOX WAYS ON X & W AXIS (3) OUTRIGGER TABLE SUPPORTS ON EACH SIDE OF TABLE CHIP CONVEYOR NOTE: MACHINE PREPPED FOR CH-16 CNC FACING HEAD MACHINE PREPPED FOR CNC ROTARY TABLE 1829 MM X 2134 MM CNC ROTARY TABLE AVAILABLE AT ADDITIONAL COST

ID	MA34397
Make	Kuraki,Japan
Model	KBT-10DX
YOM	1998
Condition	Good Condition
Photo	See Photo
Control : Fanuc 15M Spindle Diameter: 100 mm X-Axis Travel : 1500 mm Y-Axis Travel : 1000 Z-Axis Travel : 800 W-Axis Travel : 10 ~ 510 Distance Between Table Top Surface & Spindle Center : 0 ~ 1000 mm Table Size : 950 x 1100 mm Table Indexing : 90 deg. Table Load Weight : 3000 Kg Spindle Taper : CAT 50 Spindle Speed : 5 - 1300 RPM Spindle Motor : 15 HP Feed Rate (X,Y,Z W): 0.04 IPM - 157.5 IPM

ID	MA34325
Make	LX20TL3
Model	WH10
YOM	2000
Condition	Good Condition
Photo	See Photo
Control system Heidenhain . TNC 426 Diameter of working spindle . 100 mm Travel X-axis . 1250 mm Travel Y-axis . 1120 mm Spindle speed . 0 - 1800 /min. Spindle travel - W axis . 630 mm Travel Z-axis . 1000 mm Spindle taper . ISO 50 . Clamping area of rotary table . 1120 x 1000 mm Machine weight . 13000 kg Machine dimensions l x w x h . 6130 x 3600 x 2750 mm program running approx. 13,000 hours

ID	MA34236
Make	LX20TL3
Model	WHN13
YOM	1979
Condition	Good Condition
Photo	See Photo \| See Video
The machine had been serviced and Control upgraded somewhere after 2004. Used short time after that. Spindle diameter 130 mm Travel distances: X/Y/Z/W 2800x2000x1250x1250 mm Spindle ISO50 Table (swiveling)1800 x 1800 mm Table load 12000 kg FANUC DC Servo motor model 30 Machine dimensions 7480 x 6300 x 4800 mm Machine weight 32t Faceplate Two milling heads Control: CNC SIEMENS Sinumerik 802C

ID	MA34192
Make	Toshiba Japan
Model	BTF130.R22
YOM	2002
Condition	Good Condition
Photo	See Photo \| See Video
Travel : X (Cross movement of Column) 3000 mm (118.1�) Y (Vertical Movement of Spindle head) 2300 (90.6�) Z (Longitudinal movement of table) 1600 (63.0�) W (Ram extension) 400 (15.7�) Max. workpiece dimensions D2800 x 2300 mm (110 x 90.6�) Max. cover open width 2400 mm (94.5�) Table : Size 1800 x 2200 mm (70.9 X 86.6�) Loading capacity 20000 kg (44000 Lbs) Indexing 0.0001 deg. Spindel : speed 40 ~ 12000 rpm Spindle Nose Dia. 190 mm (7.48�) Type of spindle Taper Hole 7/24 Taper No. 50 Exten ram size 380 x 380 mm Motor 22Kw AC (2-min. Rating) 18.5Kw AC (continuous rating) Feedrate XYZ 1~ 10000 mm/min (0.04 ~ 393.7�) W 1 ~ 8000 mm/min. (0.04 ~ 315.0�) Rapid Feedrate XYZ 18000 mm/min (708.7�) W 10000 mm/min. (393.7�) B 500 deg./min. ATC Type of tool shank MAS BT50 Tool storage capacity 38 Machine size Height 5560 mm (203�) Floor space 8810 x 9000 mm (347 x 354�) Mass of machien with numerical control 40000Kg(88000 Lbs) Standard Accessories : refer to the attachment

ID	MI7587
Make	WMW Union ,Germany
Model	BFKF150/1
YOM
Condition	Good Condition
Photo	See Photo
Spindle : 150mm; Table size : 1600mm x 1250mm; X travel - 2200mm; Y travel - 1800mm; Z travel - 1200mm; Max. workpiece weight : 12000. kg; Max. spindle speed 1600 rpm; Spindle motor power : 80.0 kW; Cnc Control : HEIDENHAIN; Books, Manuals, Panel complete.

ID	MA34150
Make	LX20TL3
Model	WHQ13
YOM	2005
Condition	Very good condition
Photo	See Photo
Spidle diameter 130 mm CNC SIEMENS SINUMERIK X 3.500 mm Y 2.000 mm Z 1.250 mm W 800 mm Rotary Table Transfert 2.200 x 1.800 mm Capacity Load 12/15 Ton. Automatic Tools Changer

ID	MA34145
Make	WMW Union
Model	CBFK150
YOM	1985
Condition	Excellent condition,under power
Photo	See Photo
Control: Siemens Sinumerik 840C Table size:1600x2000mm Table weight 12000kg Spindle diameter:150mm Spindle taper:SK 50 Travel XYZW:2500x1600x1600x850mm Spindle Speed:5-1120rpm Weight:31700kg Complete with 5th axis

ID	MA34113
Make	Toshiba Shibaura
Model	BTD13FR22
YOM	2004
Condition	Good Condition
Photo	See Photo
Spindle Dia. 130 mm X � 3000 mm Y � 2300 Z � 1600 W - 700 5~ 2500 rpm 22/18 Kw BT 50 Table Size : 1800 x 2200 mm Indexing 0.001˚ Load 10 tons ACT : 60 tools Chip conveyor Through spindle coolant Chiller Control : TOSNUC 888 Coming with a lot of tools / angle plates. Note: 3 x 40 OT containers + 1 x 20 ft dry container

ID	MA34070
Make	LX20TL3
Model	WHN13.4B
YOM	1987
Condition	Good Condition
Photo	See Photo
Control: HEIDENHAIN TNC 155 for 4 axes (X / Y / Z / W) � Table rotation 90 � via M function � Continuous table rotation via HEIDENHAIN VRZ 183A � 1 Position display HEIDENHAIN VRZ 183A for B-axis table rotation � 1 vertical milling head \|FP50 / ISOP50 � 1 spindle guide sleeve � 30 tool holders ISO50 � 2 clamping angles 1400x500 mm � 1 coolant device � Spare parts package � Operating instructions Technical details: Spindle diameter 130 mm Spindle mount ISO50 Spindle adjustment 800 mm Spindle speed 1.25-900 rpm Main spindle power 37 kW Table size 1800x1600 mm Longitudinal / transverse / vertical 1250/2200/1700 mm Table load 12000 kg Machine weight: approx. 39000 kg

ID	MA34061
Make	Kuraki,Japan
Model	KBT11WA
YOM	2012
Condition	Good Condition
Photo	See Photo \| See Video
FEATURES: FANUC 31I-MODEL A5 CNC CONTROL B-AXIS CONTOURING ROTARY TABLE 60 ATC THROUGH SPINDLE COOLANT CHIP CONVEYOR PROBE SPECIFICATIONS: SPINDLE DIAMETER:4.33" X-AXIS, TABLE TRAVEL:78.74" Y-AXIS, VERTICAL TRAVEL:59.05" Z-AXIS, SPINDLE TRAVEL:19.68" W-AXIS, COLUMN INFEED TRAVEL:57.08" ROTARY TABLE SIZE:62.99" X 55.11" TABLE WEIGHT CAPACITY:14,300 LBS. TABLE INDEX, B-AXIS:.001 DEGREE SPINDLE SPEEDS:5-3000 RPM SPINDLE TAPER:CAT 50 BIG PLUS SPINDLE DRIVE MOTOR:30 HP APPROXIMATE MACHINE DIMENSIONS:207" X 240"" X 156" APPROXIMATE MACHINE WEIGHT:57,200 LBS. EQUIPPED WITH: FANUC 31I-MODEL A5 CNC CONTROL 62.99" X 55.11" CONTOURING CNC ROTARY TABLE 60-STATION AUTOMATIC TOOL CHANGER BIG-PLUS DUAL CONTACT SPINDLE SYSTEM TOOL SETTER TOUCH PROBE SPINDLE CHILLER COOLANT THROUGH SPINDLE CHIP CONVEYOR FULL CHIP AND SPLASH ENCLOSURE MACHINE HOURS: 3906 CUT HOURS

ID	MA34057
Make	Kuraki,Japan
Model	KBT13DXAP
YOM	1990
Condition	Good Condition
Photo	See Photo
Boring spindle diameter 130 mm Automatic pallet changer APC 2 pallets Pallet size 1600 x 1800 mm Pallet load max. 6000 kg Table load (not using the APC) max. 10000 kg Spindle � table surface min/max. 0 / 1800 mm Spindle nose � table centre min/max. 700 � 2000 mm Table indexing B 0.001 degrees Table cross travel X 3300 mm Headstock vertical travel Y 1800 mm Spindle axial travel W 700 mm Column longitudinal travel Z 1300 mm Collision circle in work area max. � 2400 mm Cutting feeds X,Y,Z,W 1 � 3600 mm/min. B 0.1 � 360 �/min Rapid traverses X,Y,Z 10000 mm/min. B 1 rpm Thrust in the Z Axis max. 25000 N Spindle motor rating 22/26 KW Spindle speed range 5 � 2500 rpm Number of gear steps 3 Spindle torque max. 2900 Nm Boring spindle diameter 130 mm Spindle taper BT 50 Tool magazine positions 90 Tool � with/without adjacent tools max. 125 / 230 mm Tool length max. 400 mm Tool weight max. 25 kg Milling capacity in S48C max. 960 cm3/min. Boring capacity in S48C max. � 70 mm Tapping capacity in S48C max. M72 Machine weight 53000 kg Machine dimensions l x w 7000 x 9500 mm Machine height h 4750 mm Control Fanuc 15M

ID	MA33904
Make	Mas/Kovosit
Model	WXH100NC
YOM	2014 the electrics were overhauled
Condition	Good working condition
Photo	See Photo
CNC Siemens Sinumerik 828d Table clamping surface: 1000x1120 mm Min. spindle head distance from table axis: 387 mm Min. spindle spindle distance from table: 50 mm Axis X table travel: 1200 mm Drive axis Z: 1000 mm Y-axis spindle stroke: 800 mm Max. table load: 30,000 N / 3000 kg Spindle: Cone 50 Spindle speed range: 6-3000 rpm Number of selectable speed ranges: 2 Number of revolutions: continuously Feed speed spindle, stand, table: 2 - 2000 mm / min Fast-moving spindle, stand, table: 8000 mm / min Table rotation: Continuous feed rate: 0.034 - 1 min-1 Fast speed table: 2 min-1 Total installed power: 50 kVA Overall dimensions: length 6655 x width 4050 x height 3270mm Weight: approx. 17,000 kg

ID	MA33896
Make	Kuraki,Japan
Model	KBT11WDX
YOM	1986
Condition	Good Condition
Photo	See Photo
SPINDLE DIAMETER: 110 MM TAPER IN SPINDLE: 50 VERTICAL TRAVEL OF HEADSTOCK: 1499 MM CROSS TRAVEL OF TABLE: 2000 MM SPINDLE TRAVEL (IN & OUT): 650 MM SADDLE TRAVEL (IN & OUT): 1450 MM TABLE SIZE: 1397 MM X 1626 MM SPINDLE SPEEDS (3 RANGES): 5-2500 RPM FEEDS:.04-157 IPM RAPID TRAVERSE:394 IPM EQUIPPED WITH: FANUC 11M-A CNC CONTROL 40-STATION AUTOMATIC TOOL CHANGER BUILT IN ROTARY TABLE 30/25 HP SPINDLE MOTOR CHIP CONVEYOR FEATURES: FANUC 11M CNC CONTROLS 40-STATION AUTOMATIC TOOL CHANGER BUILT IN ROTARY TABLE

ID	MA33895
Make	Kuraki,Japan
Model	KBT13DXA
YOM	1986
Condition	Good Condition
Photo	See Photo
SPINDLE DIAMETER:130 MM TAPER IN SPINDLE: 50 VERTICAL TRAVEL OF HEADSTOCK:2000 MM CROSS TRAVEL OF TABLE:3000 MM SPINDLE TRAVEL (IN & OUT):700 MM COLUMN TRAVEL IN & OUT:1300 MM TABLE SIZE:1600 MM X 1800 MM TABLE WEIGHT CAPACITY:26,400 LBS SPINDLE SPEEDS (2 RANGES):5-1300 RPM SPINDLE MOTOR:25 HP / 22 KW FEEDS:0.04-141.73 IPM RAPID TRAVERSE:393.70 IPM EQUIPPED WITH: FANUC 11M CNC CONTROL 40-STATION AUTOMATIC TOOL CHANGER BUILT IN CNC ROTARY TABLE COOLANT SYSTEM HARDENED WAYS CHIP CONVEYOR 30/25 HP SPINDLE MOTOR FEATURES: FANUC 11M CNC CONTROL 40-STATION AUTOMATIC TOOL CHANGER BUILT IN ROTARY TABLE

ID	MA33828
Make	WMW Union ,Germany
Model	BFT90/5
YOM	1982
Condition	Good Condition
Photo	See Photo
Travels: X - 1.000 / Y - 1.000 mm / Z - 1.600 mm Spindle diameter: 102 mm Drilling spindle stroke: 710 mm Spindle holder: ISO 50 Table size: 1.250 x 1.400 mm Spindle speed: 8 - 1.600 stepless rpm Table rotation: 360�stepless Table load: 2,5 t Spindle motor: 17,5 kW Total power requirement: 33 kW Machine weight: ca. 9.200 kg Space requirement: ca. 5,0 m x 5,0 m Control :HEIDENHAIN TNC 135

ID	MA33688
Make	LX20TL3
Model	WHN13.4
YOM	1977
Condition	Good Condition
Photo	See Photo
Spindle diameter: 130 mm Drive power 30 KW Travel x 2000 mm Travel y 2000 mm Travel distance z 1250 mm B-360 � via digital display Spindle stroke 800mm SK 50 Spindle revolution max: 710rpm Table load 12,000kg Table size 1800 x 1800 mm with slide gate Control Heidenhain TNC 135

ID	MA33687
Make	LX20TL3
Model	WHN13CNC
YOM	1995
Condition	Good Condition
Photo	See Photo
spindle diameter: 130 mm x-travel: 3500 mm y-travel: 2000 mm z-travel: 1250 mm w-axis: 800 mm b-axis: 360 � table-size: 2200 x 1800 mm

ID	MA32159
Make	Tos Czech
Model	WHN13
YOM	2003
Condition	Good Condition
Photo	See Photo
Spindle diameter mm 130 Axe (W) mm 800 Spindle revolutions 0-800 rpm Main motor output kW 37,0 Axe X (X) mm 3500 Axe Y mm 2000 Axe (Z) mm 1250 Table mm 1800 x 2200 Table loading kg 12000 Machine dimensions: length mm 7045 width mm 5895 height mm 4495 machine weight kg 32000

ID	MA32112
Make	Scharmann
Model	Ecocut 1.2 with TDV 1
YOM	1997/2004 complete retrofit
Condition	Good Condition
Photo	See Photo
Travels: X-axis: 1200 mm Y-axis: 800 mm Z-axis: 1400 mm Spindle: Spindle taper ISO 50 inside / ISO 40 Spindle diameter: 130 mm Spindle speed: 12-4000 rpm Spindle motor power: 15 kW Table clamping surface: 750 x 850 mm Table load: 3000 kg Rapid traverse :12 m/min Feed range: 1-6000 mm/min Total weight: 16050 kg Accessories: High pressure - cooling system CNC round table Control: CNC Siemens Sinumerik 810M

ID	MA31641
Make	Fermat
Model	WFT 13 CNC
YOM	2011
Condition	Good Condition
Photo	See Photo
Control system Heidenhain . TNC 530 Diameter of working spindle . 130 mm Travel X-axis . 4000 mm Travel Y-axis . 2500 mm Spindle speed . 0 - 3000 /min. Cooling through spindle Pressure of cooling . 20 bar Spindle travel - W axis . 730 mm Travel Z-axis . 1700 mm Tool magazine Number of positions in magazine . 20 Spindle taper . ISO 50 . Clamping area of rotary table . 1800 x 2200 mm Max. weight of workpiece . 15000 kg EN: chipper conveyor universal milling head UHM 30 with 1�index Probe Heidenhain TS 640 Hours: CNC system: 14739:31 machine time: 10172:53 Program: 3669:59 spindle: 3581:03 axis: 3627:18 square included

ID	MA31283
Make	TOS
Model	WHN13.4B
YOM	1986
Condition	Good Condition
Photo	See Photo \| See Video
Controller NC TESLA/ with DRO spindle diameter : 130 mm x-travel : 2200 mm y-travel : 2000 mm z-axis : 1250 mm W-axis (spindle longitudinal) : 800 mm table : 1600x1800 mm table max. load 12t spindle headstock drive : 37 kW weight of the machine ca. : 32.5 t with Digital Readout on 3 axis The machine is equipped with ballscrews.

ID	MA31087
Make	Union 130
Model	Chemnitz 130
YOM
Condition	Good Condition
Photo	See Photo
Horizontal boring machine UNION 130 CHEMNITZ 130, CNC Siemens 840 D Machine in 2002, modernization in 2017 (new machine) Also included is a universal milling head 2000 year of release, manufacturer UNION-NBU 15, Toolholder: ISO 50 Diameter of the spindle: 130 mm x axis: 3200 mm y-axis: 2500 mm Z axis: 1500 mm b-axis: 360 � w-axis: 750 mm U-axis: 220 mm Operation: Siemens 840 D Tool: SK 50 Rotational speed: 2.5-280 rpm support plan Spindle Speed Range: 5-3000 rpm Table size: 1600x2000 mm Feeding speed: Z / Y / W, 1 . 6.000 mm / min Accelerated stroke, speed: Z / Y / W, 15 m / min Torque on the spindle: 2415 nm Tool Weight Max: 25 kg Tool shop: 60 seats Load per table: 6,5 t Cooling device: IKZ / CTS Total power requirement: 51 kW Machine weight: 35 t Dimensions of machine LxWxH: 5,0x6,0x4,45 m Dimensions Electrical cabinet LxWxH: 2,0x0,68x2,3 m

100

ID	MA31086
Make	TOS
Model	WHN13.8B
YOM	1987
Condition	Good Condition
Photo	See Photo
Spindle dia : 130 mm, X travel : 3500 mm, Y travel : 2000 mm, Z travel : 1250 mm, Spindle travel : 800 mm, Spindle taper : ISO50, Table Size : 1600 x 1800 mm, Spindle motor : 38 kW, Spindle Speed : 1.25 - 900 RPM, Max. weight on table : 12 Tons, Working feeds : 0- 2500 mm/min, Total Weight : 34 Tons, Heidenhain TNC 150 (4 Axis) CNC Control, With 1 Universal Milling Head, 1 Vertical Milling Head & Toolholders.

101

ID	MA31042
Make	Tos Czech
Model	WHQ13
YOM	2006
Condition	Good Condition
Photo	See Photo
Spindle diameter - 130mm X travel - 4000mm Y travel - 2500mm Z travel - 1250mm W travel - 800mm Table - 1800x2200mm

102

ID	MA30672
Make	Graffenstaden
Model
YOM	1968
Condition
Photo	See Photo
AFS type 114z retrofitted in 2003 cnn siemens 802-5 axes 1400x1700 table 130mm spindle

103

ID	MA30426
Make	Tos Czech
Model	WHN13A
YOM
Condition	Good Condition
Photo	See Photo
Spindle dia: 130 mm, X axis: 2000 mm, Y axis: 2000 mm, Z axis: 800 mm, W axis:1250 mm, Table: 1800 x 1800 mm, Weight: 32000 kg, Equipment: Facing chuck Vertical head Tool holder approx.20-30 Retrofited New motors on all axis New linear encoders New electrical cabinet

104

ID	MA30382
Make	WMW Union ,Germany
Model
YOM	1989
Condition	Good working condition
Photo	See Photo
Control: Heidenhain control TNC 355 Travels: Height movement head stock (Y): 2020 mm Boring spindle movement (W): 900 mm Cross slide movement (U): 320 mm Travels Cross movement clamping table X :2785 mm Lengthwise movement clamping table Z -without steady rest: 2345 mm, - with steady rest: 1695 mm, Tool carrier Spindle diameter: 130 mm Tool taper boring spindle: ISO 50 Rapid movement: Axis Y: 5000 mm/min Axis W, U 3150 mm/min Job carrier Clamping area : 1800 x 2000 mm Job weight max :8000 Kg Clamping table Rotary movement: 360 � Optical table positioning: 4 x 90� Centering at flat support mm 500 H6 Outside diameter flat support: 785 mm Revolutions step less: Boring spindle in 4 areas min-1 5-1000 Flat support in 2 areas min-1 5-250 Feeds (step less): Axis Y 5-2500 mm/min Axis W, U 2-2500 mm/min Working values: Main drive power 50 kW Torque, max. boring spindle Nm 3150 Torque, max. flat support Nm 5300 Diameter boring max 800 mm Diameter Flat max 1400 mm Feed force axis Y 20000 N Feed force axis W 10000 N Feed force axis X 20000 N, axis Z 25000 N Whole machine input power 100 kW Deepest position boring spindle below upper edge clamping table 80 mm Thread led 1-12 mm, 1/24-1/2 inch Max. moment of inertia (I) of work piece kgm2 5000 Max. load torque of clamping table 16000 Nm Clamping table T-nuts width 28 mm T-nuts distance 160 mm Centering mm 100 H6 Feeds step less: X 5-2500 mm/min Z 2-2500 mm/min B 4-2500 mm/min (with regard to � 1000) Rapid movements X 5000 mm/min Z 3400 mm/min B 5000 mm/min (with regard to � 1000) Total machine weight net 37000 Kg Accessories: Clamping angles, tool tapers SK50 about 100, and maybe more. (There is also angle head, complete set of tools: not included in the price. We can discuss everything.)

105

ID	MA30113
Make	Kuraki,Japan
Model	KBT15DXA
YOM	1991
Condition	Good Condition
Photo	See Photo
Table : 1600 x 1800 mm, Spindle diameter : 150 mm, Stroke : X,Y,Z,W : 3000 x 2050 x 1300 x 700 mm, Table Index : 0.001 deg, ATC-15 Fanuc 15 M.

106

ID	MA30090
Make	LX20TL3
Model	WHQ13
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter:130 mm Work piece weight:12000 kg X-travel:3500 mm Y-travel:2500 mm Z-axis:1250 mm W-axis:800 mm Table-size:1800x2200 mm Spindle drive:37 kW Tool magazin: 40 Places Tool taper ISO 50 Turning speed range:10 - 3000 U/min Weight of the machine ca.:38,65 t Dimensions of the machine ca.:6960 x 6805 x 5211 mm Control: Heidenhain iTNC 530

107

ID	MA29893
Make	Saimp
Model	Mectra16
YOM	1984
Condition	Good Condition
Photo	See Photo
Spindle dia: 130 mm, Cross travel: 3000 mm, Longitudinal travel: 1300 mm, Vertical travel: 1700 mm, Taper :ISO 50, Spindle drive: 22 Kw, Table dimensions: 3000 x 1000 m, N.02 Rotary table : 1200 x 900 mm, Tool changer 72 positions, Milling head, Control: Heidenhain TNC415

108

ID	MA29882
Make	Pegard
Model
YOM
Condition	Excellent condition,under power
Photo	See Photo
1) Type : 130 P YOM : 1998 Complete Upgraded Control : Heidenhain TNC 426/430 Condition : excellent / under power at plant. Techincal details : X = 2400 mm Y = 1800 mm Z = 750 mm W= 2400 mm B = 360� Continious Table 1600 x 2000 m / load max. 10 tons Spindle dia : 130 mm / ISO 50 Spindle speeds 4-1250 rpm / stepless Machine weight : 35 tons. -------------------------------------------------------------------- 2) Make : Pegard / Belgium Type : 130 S YOM : 1998 Complete Upgraded Control : Heidenhain TNC 426 Techincal details : X = 2000 mm Y = 1400 mm Z = 750 mm ( spindle stroke ). W= 2400 mm ( Column stroke ) B = 360� continious ( Table ) Table 1200 x 1400 mm / load max. 6 tons Spindle dia : 130 mm / ISO 50 Spindle speeds 4-1250 rpm / stepless Machine weight : 30 tons. with some tooolings only with p130S

109

ID	MA29845
Make	WMW Union ,Germany
Model
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter: 152 mm, Taper: #50, Spindle RPM min-max: 5-2,500 RPM, Table size: 2000 x 1600 mm, X table cross: 2743 mm, Y headstock vertical: 1830 mm, W quill: 686 mm, Z spindle: 1575 mm, Feeds, inf variable: 1-999 mm/min, Motor: 50 KW 69 HP, Rotary table capacity: 25,000 LBS (11350 kg), Rapid traverse rates: 393 IPM, Max rotary table speed: 3 RPM, Machine weight ( approximate) 75,000 LBS (34000 kg), Control: Fanuc O CNC

110

ID	MA29844
Make	WMW Union ,Germany
Model	BTF105
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter: 100 mm, Spindle taper: No.50, Spindle speeds (inf variable , 3 ranges): 4-2500 RPM, X (cross) travel: 1270 mm, Y (vertical) travel: 990 mm, Z (saddle) travel: 1245 mm, W (spindle) travel: 483 mm, Feed range: 07-197 IPM, Rapid traverse (X,Y,Z): 393 IPM, Rapid traverse B (table rotation): 3.2 RPM, Spindle motor: 34 HP, Table type: Rotary, Table size: 1257 x 1003 mm, Equipped with: Heidenhain CNC Control Full way covers

111

ID	MA29799
Make	LX20TL3
Model	WHN13.8
YOM	1995
Condition	Good Condition
Photo	See Photo
Spindle diameter: 130 mm, Travel X: 3500 mm, Travel Y: 2500 mm, Travel Z: 1520 mm, Travel W: 800 mm, Taper: ISO50, Table surface: 1800 x 1800 mm, Max. work piece weight: 12000 kg, Main motor power: 37 kW, Spindle speed: 1600 rpm/min, Equipment: 4 pcs head, Control: CNC Heidenhain TN 415

112

ID	MA29491
Make	WMW Union ,Germany
Model	CBFK150/2
YOM	1989
Condition	Good Condition
Photo	See Photo
Spindle dia: 150 mm, X travel: 3000 mm, Y travel: 2000 mm, Spindle taper ISO: 50, Column travel on compound rest: 1600 mm, Feed movement: 700 mm, Table size: 2000 x1600 mm, Max. work piece weight: 12500 kg, Spindle turning speed- stepless: 10-2500 U/min, Feeds stepless: 1-9.999 mm/min, Rapid traverse: 10000 m/min, Main drive DC: 50 kW, Total power requirement: 90 kW, Weight of the machine ca: 40 ton, Control: Siemens Sinumerik 850M

113

ID	MA29487
Make	Accut
Model	HBM110CNC
YOM
Condition	Brand New
Photo	See Photo
Spindle dia: 110 mm, Table: 1250 x 1100 mm,5000 kg load,0.001 degree indexing, Boring spindle speed:10-1000 rpm, X/Y/Z/W axes stroke: 1600/1200/1400/600 mm, Main servo spindle motor power: 11 kW, Dimensions and weight:5.3 x 3.3 x 3.8 m,17 tons Fanuc 0i-mate MD CNC system, 4 axis simutaneously controlled of X/Y/Z/B axes, Fanuc brand feed motors on X/Y/Z axes, CTB brand feed motor on W axis, Schneider brand electrics, GIFU brand ATC,20 pot,chain type Fagor brand angle encoder, Facing head,600 mm diameter manual

114

ID	MA28954
Make	LX20TL3
Model	WHN13.8
YOM	New in 1986/partly overhauled/new control in 2015
Condition	Good Condition
Photo	See Photo
Spindle diameter:130 mm X-axis:4700 mm, Y-axis:3500 mm, Z-axis: 1250 mm, W-axis: 800 mm, B-axis: 360,000, Table: 1800 x 1800 mm Work piece weight / max. work pice: 15000 kg, Spindle speed max. / Max. Spindle speed: 710 UPM Spindle taper / Spindle taper: SK 50 Weight / weight 42000 kg Control: HEIDENHAIN iTNC 530

115

ID	MA28891
Make	San Rocco
Model	Futura100MF
YOM	1985
Condition	Good Condition
Photo	See Photo
Spindle dia : 100 mm. X/Y/Z/W - 2000/1300/650/1200 CNC control Heidenhain TNC155 Incl. angle head

116

ID	MA28804
Make	Kuraki,Japan
Model	KBT13DXA
YOM	1990
Condition	Good Condition
Photo	See Photo
Work table size : 1800 x 2000 mm, Loading weight : 8000 kg, X axis travel : 4000 mm, Y axis travel : 2000 mm, Z axis travel : 1300 mm, W axis travel : 700 mm, Spindle Speed : 5~2000 rpm, Tool storage capacity : 60 pcs, Type of tool shank : BT 50, Spindle drive motor : 22/18.5 kW, Control system F-15M.

117

ID	MA28683
Make	WMW Union ,Germany
Model	BFT130/6
YOM
Condition	Good Condition
Photo	See Photo
Spindle Dia : 130 mm, Spindle Taper : 50 ISO, Facing Head Dia : 800 mm, Table Size : 2000 x 1800 mm, Vertical Traverse : 2200 mm, Cross Traverse : 2000 mm, Spindle Speeds to : 900 RPM, RETROFITTED WITH FAGOR CNC CONTROL.

118

ID	MA28656
Make	WMW Union ,Germany
Model	BFT130/5
YOM	Retrofitted in 2006
Condition	Good Condition
Photo	See Photo
Spindle diameter : 130 mm, Travel X axis : 2100 mm, Travel Y axis : 2000 mm, Travel Z axis : 1000 mm, Table size : 2000 x 1800 mm, Control : Heidenhain TNC 124 CNC Control.

119

ID	MA28574
Make	Wotan,West German
Model	Rapid l-M
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter: 130 mm, X axis travel; 1280 mm, Z axis travel: 1000 mm, Rotary table : 360 degree, Table size: 800 x 800 mm, ATC: 32 Spindle speeds: 25-1250 r.p.m.,'Tool taper: BT 50, Max weight on table: 1000 kg, Feeds: Infin, Equipped with twin pallet, Motor: 12 HP, Weight: 11000 kg Control: Fagor 8030,

120

ID	MA28559
Make	San Rocco
Model	MEC120
YOM	1979 / 1990
Condition	Good Condition
Photo	See Photo
Spindle diameter : 120 mm, X-travel : 2100 mm, Y travel : 1500 mm, Z travel : 1500 mm, Spindle stroke : 800 mm, Table size : 1200 x 1520 mm, Table : 360 degrees, Taper : ISO 50, RPM up to : 2000 U/min. Accessories :- Telescopic Covers. Automatic tool clamping. Ball bearing spindles. Hydraulic clamping. Coolant. CNC-control model ECS 2300.

121

ID	MA28459
Make	LX20TL3
Model	WHN13.8
YOM	1995
Condition	Good Condition
Photo	See Photo
Spindle dia: 130 mm, X travel: 3500 mm, Y travel: 2000 mm, Z travel: 1250 mm, W travel: 800 mm, Increased working table: 1800 x 2200 mm, Electronic probe: Heidenhain TS 120, Total machine power input: 85 kVA, Max. work piece weight (for table 1800 x 2200 mm): ca.12000 kg, Machine mass with the same parameters , but with X - 3500 mm: ca. 34,500 kg, Control: Heidenhain - TNC 415 B.

122

ID	MA28458
Make	LX20TL3
Model	WHN13.8
YOM	2003
Condition	Good Condition
Photo	See Photo
Spindle dia: 130 mm, Hollow cone of the work spindle: ISO 50, Speed range of the spindle: 10-2800 1/min, main motor power: 37 kW, X travel: 3500 mm, Y travel: 2500 mm, Z travel: 1250 mm, W travel: 800 mm, Working feeds of the machine groups X,Y,Z and W: 4-6000 mm/min, Rapid traverse of the machine groups X,Y,Z and W: 10000 mm/min, Clamping area of the table: 1800 x 2200 mm, Max. weight of the work piece: ca.12000 kg, Weight of the machine: ca. 38.650 kg, Total installed power:32 kVA, Operating voltage: 3 x 400 V, Control: Heidenhain - TNC 426.

123

ID	MA28386
Make	Scharmann
Model	MC90NCC
YOM
Condition	Good Condition
Photo	See Photo
Spindle diameter : 90 mm, Travel X : 1340 mm, Travel Y : 990 mm, Travel Z : 950 mm, B axis : 360 degree, 4 axis, Spindle taper : SK50, Spindle motor : 10 - 150 U/min, Control : Heidenhain TNC 310 cnc control.

124

ID	MA28384
Make	Tos Czech
Model	WHN9B
YOM
Condition	Good Condition
Photo	See Photo
Spindle dia: 100 mm, Cross travel of the table X: 1250 mm, Vertical stroke of spindle carrier Y: 900 mm, Spindle taper: SA 40, Table area: 1120 x 1000 mm, Spindle stroke: 680 mm, Longitudinal travel:1000 mm, Maximum weight admited on table: 9000 Kg, Spindle speed: 8 � 1120 tr/mn, Maximum automatic longitudinal feeds: 2 � 2500 mm/mn, Rotary table: 360 � spindle motr: 20 kw, Approximate weight: 12000 kg, Dimensions: 4700 x 2300 x 2750 mm, Control: CNC system Heidenhain

125

ID	MA28383
Make	Kearns
Model	SH75
YOM
Condition	Working
Photo	See Photo
Spindle diameter : 75 mm, Spindle speed : 1120 rpm, Travel X axis : 1250 mm, Travel Y axis : 1000 mm, Travel Z axis : 1000 mm, Table : 1000 x 1000 mm, 360 degrees, Weight : 9,5 ton. Control Fanuc OM make CNC. With facing chuck.

126

ID	MA28380
Make	WMW Union ,Germany
Model	BFT90/3
YOM	1980
Condition	Good Condition
Photo	See Photo
Spindle dia: 102 mm, Cross way of table (X): 1000 mm, Vertical way of spindle stock (Y): 1000 mm, Drilling depth (W): 710 mm, Table rotation ( B): 360 � Speeds of spindle: 8.1600 U/min/rpm, Feeds drilling: 0.3000 mm/min, Feeds milling: 0.3000 mm/min, Taper of spindle: ISO 50, Max. weight of job: 2,5 ton, Connected power: 33 kW, Weight of machine: 9,27 ton, Control: Heidenhain TNC 122/ 3 axes with digital display.

127

ID	MA28370
Make	Tos Czech
Model	WH10
YOM	1983/1986
Condition	Good Condition
Photo	See Photo
Spindle: 100 mm, X travel: 1250 mm, Y travel: 1120 mm, Z travel: 1000 mm, W travel: 630 mm, ISO 50, 16-1250 / min, Table: 1000 x 1120 mm, Approximately 3 ton kg, 20 kW, Weight approximately: 12 ton, Control: Heidenhain TNC 155.

128

ID	MA28245
Make	Wotan,West German
Model	Cutmax2
YOM	1995
Condition	Good Condition
Photo	See Photo
NC-Rotary Table :- Clamping size : 1600 x 1400 mm, Max table load : 4000 kg, Position : 360.000 x 0.001 degree, Travel, Feeds :- X axis (table longitudinal) : 1800 mm, Y axis (headstock vertical) : 1700 mm, Z axis (column movement) : 1300 mm, W axis (quill stroke) : 600 mm, Max feed rate (X,Y,W) : 1-8.000 mm/min, Max feed rate (Z) : 1-6.000 mm/min, Max feed rate (B) : 0-2.5 rpm, Working unit :- Dia quill : 120 mm, Tool taper : SK50, DIN69871AD, Spindle speed : 1-3.000 min-1, Gear steps : 3 (1-300, 301-940, 941-3000 rpm), Power : 30 kW, Tool Magazine :- Magazine type : chain magazine, Number of tools : 40, Max dia without free neighbour places : 125 mm, Max dia with free neighbour places : 370 mm, Max workpiece length : 600 mm, Max workpiece weight : 40 kg, Control : FANUC Series 16 M. Accessories :- Electronical hand wheel, coolant equipment with chip conveyor, without machine covering.

129

ID	MA28240
Make	WMW Union ,Germany
Model	BFT130/6
YOM	1984
Condition	Good Condition
Photo	See Photo
Spindle diameter : 130 mm, Cross travel of table : 2235 mm, Vertical adjustment of drilling slide : 1950 mm, Spindle stroke max : 900 mm, Spindle taper : ISO 50, Table longitudinal travel : 1400 mm, Spindle turning speed range : 5-1000 U/min, Table surface area : 1600 x 1400 mm, Voltage : 380 V, Spindle drive : 45 kW, Feeds longitudinal / cross / vertical : 5-2500 mm/min, Rapid motion - longitudinal / cross / vertical : 5 m/min, Weight of the machine : 32 t, Table load : 8 t, Table rotation : 360 degree, Radial face slide travel : 320 mm, Faceplate diameter : 785 mm, Faceplate speeds : 5-250, Total connected load : 75 kW, Dimensions of the machine : 7 x 4,7 x 4,4 m, Control : Heidenhain TNC 155 for 3 axes. Machine is without faceplate, It has table side support and some accessories.

130

ID	MA28227
Make	Femco,Taiwan
Model	BMC110R2
YOM	2006
Condition	Good Condition
Photo	See Photo
Spindle dia: 110 mm, X/Y/Z/W axis travel: 2000 x 1800 x 1700 x 500 mm, Table size: 1440 x 1600 mm, Spindle speed: 2500 rpm, Tool shank: BT50, 60 ATC, Control: Fanuc 0iMC, With 3 axes linear scales, Indexing degree: 0.001 degree.

131

ID	MA28200
Make	Schloemann
Model	BF1
YOM	New in 1994
Condition	Good condition,under power
Photo	See Photo
Spindle diameter : 125 mm, Table Size. : 1400 x 1600 mm, Travel X Axis. : 2500 mm, Travel Y Axis. : 1600 mm, Travel Z Axis. : 1400 mm, Travel W Axis. : 600 mm, Spindle Taper. : ISO-50, Spindle speed : 3000 RPM, Spindle Travel. : 600 mm, B Axis. Rotary Table. : 1�-360� (4x90�) Table Load Capacity. : 12 tons, Total Power : 45 KW, CNC Control. SIEMENS: Sienumerik 880 with Handwheel.

132

ID	MA28191
Make	San Rocco
Model	MEC120
YOM	1980
Condition	Good Condition
Photo	See Photo
Spindle diameter : 120 mm, X Travel : 2100 mm, Y Travel : 1800 mm, Z Travel : 1500 mm, Taper ISO : 50, Rotary table size : 1500 x 1200 mm, Load on table : 5000 Kg, 18 spindle speed 13 - 1000 rpm, Spindle power : 15 Kw, Spindle travel : 800 mm, Cutting feed : 3 - 1000 mm/min, Rapid feed : 5000 mm/min, HEIDENHAIN TNC 155 control system.

133

ID	MA28089
Make	WMW Union ,Germany
Model
YOM	1985/2005
Condition	Good Condition
Photo	See Photo
Spindle diameter : 110 mm, X/Y/Z/ travels : 1600 x 1250 x 1250 mm, Table size : 1250 x 1600 mm, Spindle taper : ISO 50, Machine weight approx. : 26 tons, Control : CNC contouring control Heidenhain TNC-426/430 CB.

VKengg.co.in

Category : Boring Mills

Sub-Category : Borer Horizontal Table Type CNC