VKengg.co.in

Category : Forging Equipment

Sub-Category : Hammer Forging Air Steam

Total Machines Found : 179

Select	| Machine Details
1	ID MA36410 Make Russian Model 18KP YOM Condition Good Condition Photo See Photo Capacity - 10 Ton nominal mass of drop parts without upper instr.:9 tons, effective working kinetic energy after blow 25000 kg mtr., max. working ram stroke 1400 mm, max no of blows 30/min , distance between slides 1000 mm, shut height 775 mm , ram size front to back 1200 mm , bolster size front to back 1200 mm , air pressure 7-9 MPA , height of instruments 450 min.,die-holder front to back dimensions: 1400 mm,height above floor level: 7270 mm, hammer dimensions 4400 x 10420x2700 mm,mass (less anvil block): 75 ton, weight 205 tons.
2	ID MA36374 Make Huta Zygmunt,Polish Model MPM1600B YOM Condition Good Condition Photo See Photo full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
3	ID MA36373 Make Huta Zygmunt,Polish Model MPM6300B YOM Condition Good Condition Photo See Photo Capacity:2.5 tons, Energy of blow: 7000 kg.m, Weight of falling ram: 2500 Kg, Max. tup stroke:850 mm, Guideway spacing:650 mm, Length of die steam in the up: 650 mm, Length of die steam in the cushion: 900 mm, Min.height of the die (without doveta): 300 mm, Max. weight of upper die: 800 Kg, Stroke rate: 100 spm, Steam or incoming air pressure:5-7 Kg/cm2, Average steam consumption:970 kg/h, Average air consumption:18 m3/mm, Height above the floor:4100 mm, Total height:5145 mm, Weight of anvil:475 tons, Total weight of the hammer:64 tons. Spare Ram
4	ID MA36352 Make Kramatorsk Model M2147 YOM 1980 Condition Good Condition Photo See Photo Nominal weight of falling parts: 5000 kg Blow energy: 125 kJ Number of blows per min: 50 Max course of the hammer block: 1300 mm Min height of tools without shanks: 400 mm Distance between columns: 800 mm Length of the hammer block (at direction, Perpendicular to hammer front): 950 mm Length of the die holder (at direction, Perpendicular to hammer front): 1180 mm Total weight: 139 ton
5	ID MA35492 Make Russian Model M2150 YOM Condition Good Condition Photo See Photo Nominal weight of falling parts including 1,000 kg upper die kg:10,000 Effective blow energy for continuous full blows: kJ 260 Maximum ram working stroke: mm 1,400 Minimum die height without dovetails: mm 450 Distance between ram guides in daylight: mm 1,000 Ram length front-back: mm 1,180 Sow block length front-back: mm 1,320 Air pressure Bar: 7…9 Maximum weight of upper die: kg 3,000 That includes: - milling the anvil with the portable mill; - retrofitting of the ram and sowblock; - retrofitting of all wedges and plates; - repairing the main cylinder.
6	ID MA35443 Make TMP Voronezh Russia Model MA417 YOM Condition Good Condition Photo See Photo Nominal weight of the falling parts – 750 kg. Max. number of blows per minute – 105. Kinetic energy – 1900 kg. Distance from an axis of the slider up to bed – 750 mm. Cylinder diameter – 600 mm. Diameter of the plunger – 630 mm. Max. headstock travel – 835 mm. Dimensions: -Left-to-right – 3940 mm; -Front-to-back – 1430 mm. Height above floor level – 3260 mm. Weight – with an anvil-block – 25600 kg.
7	ID MA35234 Make HUTA ZYGMUNT Model MPM3000 YOM 1967 Condition Not under power Photo See Photo  |  See Video Capacity: 3.5 ton Blow energy 10 000 kGm Weight of the falling part of 3570 kg Stroke of 1000 mm Max. Number of jumps per minute 90 Length x width x height 3620 x 2100 x 4700 mm The spacing of the guides 660 mm Dimensions of anvils length x width 550 x 450 mm Weight 100,000 kg Power supply compressed air 28 m3 / min Compressed air pressure 5-7 bar The maximum weight of the forgings is 4.0 — 24 kg Air pressure 5-7 atm Guide way spacing 750 mm Weight of Hammer 103 T In set available all equipment to hammer as under hammer steel plate and vibroisolators – 12 pcs ( made in 2014 )
8	ID MA35142 Make Huta Zygmunt,Polish Model MPM2000 YOM Condition Good Condition Photo See Photo Weight of falling part: 2480 kg Stroke length: 950 mm distance between guides: 600 mm Max weight of upper stamp: 800 kg Height of stamp above the floor: 780 mm Blow energy: 7000 kgm Max. blows per minute: 100 Air pressure: 6-8 kg / cm2 Cylinder dia: 540 mm Total weight: 62,5 tons
9	ID MA34959 Make Banning Model GOA8000 YOM Condition Good Condition Photo See Photo Blow energy: 10.000 mkg, Ram stroke: 740 mm, Number of strokes: 105 min^-1 Die height: 360-580 mm, Ram weight: 4500 kg, Ram (front to back): 800 mm, Daylight: 850 mm, Distance between the guidelines: 800mm, Anvil weight: 85.400 kg, Dimensions of anvil: 3000 x 1850 mm, Dimensions: 5500 x 3000 x 1500 mm (LxB) height of machine above floor: 470 mm, Total weight: 72 ton, Mode of operation: Pneumatisch
10	ID MA34877 Make Saito Model YOM Condition Good Condition Photo See Photo  |  See Video Nominal weight of dropping parts(kg) 5500 Stroke (mm) 1250 Cylinder diameter (mm) 570 Piston rod diameter (mm) 200 Steam Pipe size (mm) 192 Exhaust Pipe size (mm) 218 Maximum working pressure (/cm2) 7 Between Guides (mm) 840 Ram dimensions front to back (mm) 850 Bottom the impression to floor distance (mm) 1100 Floor space (mm x mm) 4200 x 2600
11	ID MA34875 Make Eumuco,Germany Model YOM Condition Good Condition Photo See Photo Capacity: 6.3 ton, Weight is ab 100 ton (ab.60 = 40) Total weight of the hammer is ab.150 ton
12	ID MA34834 Make Eumuco,Germany Model YOM 1982 Condition Good Condition Photo See Photo Impact energy, kJ 80 Falling part weight 3150kg Number of strokes per minute 56 Distance between posts 2800mm Working area height 630mm Striker mirror size 600x340mm Steam temperature maximum 200С Maximum forging weight 820kg Hammer weight 72700kg Shabot weight 47200kg Width 5000mm Depth 2490mm Height above floor level 5500mm
13	ID MA34447 Make TMP Voronezh Russia Model M213 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts:3150 kg Rated striking energy:80 kJ Max. no. of blows/min.:56 Ram stroke:1250 mm Uprights distance:710 mm Ram dimensions:750 mm Die holder:1000 mm Min. die holder to ram distance:340 mm Steam/air pressure:0.7 — 0.9 MPa Dimensions:3820 x 1800 x 5240 mm Mass (less anvil block):25 tons Mass of anvil block:63 tons
14	ID MA34439 Make Stanko-Russia Model M415A YOM 1968 Condition Good Condition Photo See Photo Nominal weight of the falling parts: 400 kg Max. number of blows per minute: 130 Kinetic energy: 950 kg Distance from an axis of the slider up to bed: 520 mm Cylinder diameter: 480 mm Max. headstock travel: 530 mm Dimensions: -Left-to-right: 3105 mm -Front-to-back: 1270 mm Height above floor level: 2720 mm Weight: -With an anvil-block: 13500 kg -Without an anvil-block: 8700 kg
15	ID MA34425 Make TMP Voronezh Russia Model MA417 YOM Condition Good Condition Photo See Photo Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg
16	ID MA34394 Make HUTA ZYGMUNT Model MPM16000B YOM 1967 Condition Good Condition Photo See Photo Blow energy :17 500 kGm Air pressure: 5-7 atm Weight of Hammer: 173 T Hammer dismounted in 2016 because cylinder broken (on the picture) Possible to repair by welding. The bushing is good condition. Ram very good condition, bought in 2008. We worked on this hammer until the day when we found the breakage. The hammer worked fine, there was good impact control. The hammer can be still working because internal busche was good condition but we decided to stop and continue production on the second hammer. We wanted to repair this hammer but we did not manage to do so because the investor withdrew and closed the plant. Possible to sale hammer partially as spare parts. I posted a few photos from 2016 when the hammer was disassembled. In enclosure you can find mix of photos from 2016 when hammer was dismounted and current.
17	ID MA34361 Make Eumuco,Germany Model YOM Condition excellent working condition Photo See Photo 1 TON
18	ID MA33793 Make Huta Zygmunt,Polish Model MPM16000B YOM Condition Good Condition Photo See Photo CAPACITY:17.500 kgm MAX. STROKE:1.000 mm STROKES:80 n°/min MIN. DIE THICKNESS:400 mm LENGHT OF DIE SEAT IN THE RAM:900 mm LENGHT OF DIE SEAT IN THE DIE HOLDER:1.250 mm CYLINDER BORE:850 mm
19	ID MI7325 Make Huta Zygmunt,Polish Model 6300A YOM Condition Good Condition Photo See Photo capcity; 2 ton Height of the hammer above floor: 4100 mm, Weight of falling part (without die): 2490 Kg, Weight of anvil block without die holder: 47.5 ton, Height of hammer above floor: 4100 mm, Guide way spacing: 600 mm, Length of die seat in tup: 650 mm, Length of seat in the die holder: 900 mm, Max. tup stroke: 850 mm.
20	ID MA33556 Make Nittan ,Japan Model YOM Condition Photo See Photo 1.5 tons
21	ID MA33389 Make Otani Model YOM Condition Good Condition Photo See Photo Capacity: 1350 kgs Table: 530 x 550 mm
22	ID MA33276 Make Kramatorsk Model MA2147 YOM 1983 Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons
23	ID MA33268 Make TMP Voronezh Russia Model M213 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts - 3150 kg Rated striking energy 80 KJ Max. no. of blows/min. 56 Ram stroke 1250 mm Uprights distance 710 mm Ram dimensions 750 mm Fzmiwtkb Die holder 1000 mm Min. die holder to ram distance 340 mm Steam/air pressure 0.7-0.9 MPa Mass (less anvil block) 25 tons Mass of anvil block 63 tons (one piece)
24	ID MI7234 Make Model YOM 1995 Condition Good Condition Photo See Photo 1) Hammer forging air steam Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overall dimensions: Floor space : 3700 x 2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons With Trimming press: Capacity: 500 ton,
25	ID MA32946 Make Russian Model 17KP YOM Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
26	ID MA32917 Make Erie Model YOM Condition Good Condition Photo See Photo Rate size pounds: 12000 lb, Cylinder bore inches: 22 inch, Stroke inches: 50 inch Ram to sow block inches min: 20 inch Between guides inches: 30 inch Ram front back inches: 36 inch Front back: 71 inch left right: 140 inch height above floor ft & in: 1-0 Head room to drop in rod ft & in: 31-7
27	ID MA32851 Make EUMUCO Model YOM Condition Good Condition Photo See Photo 6000 Kg forging hammer
28	ID MA32848 Make Model YOM Condition Good Condition Photo See Photo 1) Offer #1510 Pneumatic air forging hammer model MA4136 Made in: Russia Manufacturer: Kalinin industrial association for the production of press-forging equipment Specification: Weight of the falling parts: 400 kg Strike energy: 11 kJ Strike frequency per min: 142 Flight: 30 mm Height of the working area: 530 mm Diameter of the working cylinder: 480 mm Diameter of the compressor cylinder: 480 mm Stroke of the compressor slide: 390 mm Max. headstock stroke: 640 mm Dimensions of the working surface: -Length: 560 mm -Width: 100 mm Optimal dimensions of the forging detail: 100 mm Power: 37 kW Overall dimensions: -Length: 3200 mm -Width: 1320 mm -Height: 2700 mm Height over the floor level: 2600 mm Weight: 13 tons 2) Offer #1511 Pneumatic air forging hammer model MA4132 Manufacturer: ASTRAXAN Factory Made in: Russia Specification: Weight of the falling parts: 160 kg Number of strokes per min: 196 Effective kinetic energy of falling part by stroke: 250 kg/m Distance from ram axis-to-frame: 350 mm Anvil dimensions: -Length: 190 mm -Width: 75 mm -Anvil height above the floor: 800 mm Diameter of working cylinder: 315 mm Diameter of compressor cylinder: 330 mm Stroke run: 390 mm Optimal stamping section of work-piece: -Square: 70 mm -Rounded: 80 mm Overall dimensions: -Length: 930 mm -Width: 1860 mm -Height above floor: 2160 mm Weight of the hammer with an anvil-block: 5290 kg 3)Offer #1713 Pneumatic air forging hammer model MA4132 Manufacturer: ASTRAXAN Factory Made in: Russia Specification: Weight of the falling parts: 160 kg Number of strokes per min: 196 Effective kinetic energy of falling part by stroke: 250 kg/m Distance from ram axis-to-frame: 350 mm Anvil dimensions: -Length: 190 mm -Width: 75 mm -Anvil height above the floor: 800 mm Diameter of working cylinder: 315 mm Diameter of compressor cylinder: 330 mm Stroke run: 390 mm Optimal stamping section of work-piece: -Square: 70 mm -Rounded: 80 mm Overall dimensions: -Length: 930 mm -Width: 1860 mm -Height above floor: 2160 mm Weight of the hammer with an anvil-block: 5290 kg
29	ID MA32815 Make Kramatorsk Model M2147 YOM 1980 Condition Good Condition Photo See Photo Nominal weight of falling parts: 5000 kg Blow energy: 125 kJ Number of blows per min: 50 Max course of the hammer block: 1300 mm Min height of tools without shanks: 400 mm Distance between columns: 800 mm Length of the hammer block (at direction, Perpendicular to hammer front): 950 mm Length of the die holder (at direction, Perpendicular to hammer front): 1180 mm Total weight: 139 ton
30	ID MI7147 Make Russian Model M2150 YOM Condition Good working condition Photo See Photo  |  See Video 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
31	ID MA32667 Make Tyazhpressmash Model M1343A YOM Condition Good Condition Photo See Photo Impact energy: 50 kJ Nominal mass of drop parts: 2000 kg Max. number of blows per minute: 56 Max. stroke of headstock: 1000 mm Distance between columns in daylight: 2360 mm Distance between guides in daylight: 550 mm Working zone height in daylight: 530 mm Bottom die impression-to-floor distance: 750 mm Die impression size (LxW): 530 x 300 mm Steam pressure: 0,7.0,9 MPa Compressed air pressure: 0,6.0,8 MPa Hammer dimensions (LxW): 4900 х 1930 mm Hammer height above floor level: 5000 mm Weight of the hammer without anvil block: 18100 kg Anvil block weight: 30000 kg Total weight: 48100 kg
32	ID MA32665 Make Russian Model M2145 YOM Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
33	ID MA32447 Make Otani Model YOM Condition Good Condition Photo See Photo Capacity: 1350 kgs Ram Back-Front: 550 mm
34	ID MA32445 Make Russian Model M2145 YOM 1990 Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
35	ID MA32215 Make Russian Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
36	ID MA31989 Make Russian Model MB2145 YOM Condition Good Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, total weight 88 tons
37	ID MA31987 Make Russian Model M212 YOM 1970 Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t.
38	ID MA31734 Make Russian Model MA2147 YOM Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons
39	ID MA31571 Make Huta Zygmunt,Polish Model MPM6300A YOM Condition Good Condition Photo See Photo Weight: 2500 Kg Blows Energy: 7000 Kgm Stroke Max Ram :33.4 inc Light :25.5 inc Height Min.: 11.8 inc Weight Max Inferior Die: 800 Kg SPM : 100 Steam Pression: 5-7 Kg/Cm Air Pression: 5-7 Kg/Cm Consumption Air Pression On Minute: 18 Mcub/Mn Roll Bore: 21.2 inc Chabotte Weight : 45,5 Ton Weight Hammer Ab. :70 Ton
40	ID MA31559 Make Russian Model MA2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
41	ID MA31471 Make Model M1343 YOM 1981 Condition Good Condition Photo See Photo Impact energy, kg 50 Nominal mass of the falling parts, kg 2000 Distance between guides in light, mm 2360 Distance between guides in light, mm 2360 Dimensions of the machine Length Width Height (mm) 4900_1930_5000 Weight kg 48700
42	ID MA31466 Make Russian Model M1345 YOM 1971 Condition Good Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons.
43	ID MA31459 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
44	ID MI7002 Make HUTA ZYGMUNT Model MPM1000 YOM Condition Photo See Photo 1000 MPM HUTA, Without Ram
45	ID MA31455 Make Model M2145 YOM 1986 Condition Good Condition Photo See Photo Model mv2145 Impact energy, kJ 80 Nominal mass of the falling parts, kg 3150 Distance between guides in light, mm 710 Distance between guides in light, mm 710 Dimensions of the machine Length Width Height (mm) 3400_1900_5450 Weight kg 88000
46	ID MA31454 Make Model M2147 YOM 1982 Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
47	ID MA31443 Make HUTA ZYGMUNT Model MPM10000 YOM 1889/1980 Condition Good Condition Photo See Photo Energy : 10.000 Kg Weight of the ram 3150 Kg Ram stroke 900 mm Max weight of upper die 1000 Kg Minimum total height of the die 260 mm Air pressure 5 – 7 bar Air consumption 22 cubic meter/min No of strokes/min 90 Distance between slides 750 mm Height above the floor 4430 mm Weight of the base 64.5 ton Total weight 96,6 ton Overall dimensions 3600 mm x2100 mm x 5930 mm
48	ID MA31400 Make Model M2143 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts, kg 2,000 Impact energy, kj . 50 Maximum number of blows per minute 70 Maximum ram stroke, mm 1,200 Distance clear between guides, mm 600 Ram front-to-back dimensions, mm 670 Die-holder front-to-back dimensions, mm 900 Bottom die impression-to-floor distance, mm 800 Minimum die holder-to-ram distance, . mm 260 Steam (air) pressure, MPa 0.6-0.8 Overall dimensions, mm: floor space 3,650 x x1,660 height above floor level 5,310 Mass (less anvil block), t, approx. 18 Mass of anvil block, t, approx. 40
49	ID MA31388 Make Russian Model M1345 YOM Condition Good Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons.
50	ID MA31387 Make Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
51	ID MA31248 Make Model 17KP YOM Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
52	ID MA31237 Make Model M2150 YOM 1980 Condition Good Condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
53	ID MA31186 Make Model M2150 YOM Condition Good Condition Photo See Photo N Case description Dimensions L,mm B,mm H,mm W,ton 1 cylinder unit ready assembled with under 4800 3000 1300 32,1 cylinder plate 2 Side Column 3650 2150 1900 21,1 3 Side Column 3650 2150 1900 21,1 4 anvil block (upper Part) 4400 2200 2650 108,1 5 anvil block (lower part) 4250 3000 1750 94,6 6 metal box wit fastening and small items 1230 870 800 2,5 6 tray with drawbar arms ready assembled with axis (2 pcs) 3850 1600 850 2,2 pipe range compensator (2 pcs) lubricating system tank 8 studs (8 pcs) 1250 850 400 0,8 9 tray with crosscut chock (3 pcs) lengthwise chock (2 pcs) 2100 800 400 1,8 metal fittings (7 pcs) 10 Anvil block bottom part 3800 2300 850 48 Total 332,2
54	ID MA31144 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
55	ID MA31129 Make Model MB2145 YOM 1986 Condition Good Condition Photo See Photo Impact energy, kJ 80 Nominal mass of the falling parts, kg 3150 Distance between guides in light, mm 710 Distance between guides in light, mm 710 Dimensions of the machine Length Width Height (mm) 3400_1900_5450 Weight kg 88000
56	ID MI6956 Make Model MPM1600B YOM Condition Good Condition Photo See Photo Ram stroke : 750 mm, Energy of full blow : 1840 kgm, Quantity of stroke : 120 u/min, Mass of anvil block : 12,5 t, Mass of hammer with anvil block : 21,9 t.
57	ID MA31085 Make Model M2143 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts, kg : 2,000 Impact energy, kj . : 50 Maximum number of blows per : 70 minute Maximum ram stroke, mm : 1,200 Distance clear between guides, mm : 600 Ram front-to- back dimensions, mm . : 670 Die-holder front-to- back dimensions, : 900 mm Bottom die impression-to- floor : 800 distance, mm Minimum die holder-to- ram distance, : 260 . mm Steam (air) pressure, MPa : 0.6-0.8 Overall dimensions, mm: floor space 3,650 xx1,660 height above floor level : 5,310 Mass (less anvil block), t, approx. : 18 Mass of anvil block, t, approx. : 40
58	ID MA31066 Make Model MPM3150 YOM Condition Good Condition Photo See Photo Table size (front to back): 700 mm Stroke: 800 mm Strokes / min: 10 Working pressure: 5 - 7 atm Max. weight of upper die: 400 kg Die height: 220 mm Ram (front to back): 500 mm Air consumption: 15 m3 / min Anvil weight: 24 t Height of machine above floor: 3750 mm Total machine's height: 4380 mm Total weight: 35 t
59	ID MA31063 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
60	ID MA31032 Make HUTA ZYGMUNT Model MPM1600 YOM Condition Photo See Photo Energy of full blow: 1840 kgm Ram weight: 630 kg Ram stroke: 750 mm Spacing of guides: 430 mm Die cavity length: -In the ram: 400 mm -In the cushion: 600 mm Min. die height: 180 mm Max. load of upper die: 200 kg Height of die distribution over the floor: 800 mm Number of strokes per minute: 120 The intake air pressure: 0,5-0,7 MPa The intake vapor pressure: 0,5-0,7 MPa Average air consumption per minute: 7 m³ Average vapor consumption per hour: 380 kG Cylinder diameter: 320 mm Ram stem diameter: 240 mm Inlet pipe diameter: 80 mm Outlet pipe diameter: 80 mm Weight of anvil block: 12,5 tons Weight of hammer with anvil block: 12,5 tons
61	ID MA31031 Make HUTA ZYGMUNT Model MPM3150 YOM Condition Photo See Photo Table size (front to back): 700 mm Stroke: 800 mm Strokes / min: 10 Working pressure: 5 - 7 atm Max. weight of upper die: 400 kg Die height: 220 mm Ram (front to back): 500 mm Air consumption: 15 m3 / min Anvil weight: 24 t Height of machine above floor: 3750 mm Total machine's height: 4380 mm Total weight: 35 t
62	ID MA31029 Make Model M2143 YOM 1979 Condition excellent working condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
63	ID MA31023 Make HUTA ZYGMUNT Model MPM1600B YOM Condition Good Condition Photo See Photo - full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
64	ID MA31022 Make Huta Zygmunt,Polish Model MPM1600 YOM Condition Good Condition Photo See Photo - full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
65	ID MA30988 Make Model M2143 YOM 1979 Condition Excellent Photo See Photo Capacity : 2 tons, Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
66	ID MA30871 Make Huta Zigmunt License Model MPM3000A YOM Condition Good Condition Photo See Photo Energia del colpo / energy – kgm 10.000 Peso della mazza battente / weight of the ram – kg 3.570 Corsa max della mazza / max slide stroke– mm 1000 Luce fra le guide / light on the guide – mm 660 Peso max stampo superiore / weight max up.die – Kg 1.100 Numero colpi al min / stroke x min 90 Peso della chabotte senza porta stampi / weight chabotte without die holder – ton 70 Peso del maglio totale / total weight – ton 100
67	ID MA30866 Make HUTA ZYGMUNT Model MPM3150B YOM Condition Good Condition Photo See Photo  |  See Video ENERGY OF BLOW: 3600 kg.m STROKING RATE: 110 s.p.m. WEIGHT OF FALLING RAM: 1250 Kg STEAM OR INCOMING AIR PRESSURE:5-7 Kg/cm2 MAX. TUP STROKE :800 mm AVERAGE STEAM CONSUMPTION:650 Kg/h GUIDEWAY SPACING:550 mm AVERAGE AIR CONSUMPTION: 12 m3/mm LENGTH OF DIE SEAT IN THE TUP: 500 mm HEIGHT ABOVE THE FLOOR: 3750 mm LENGTH OF DIE SEAT IN THE CUSHION:700 mm TOTAL HEIGHT:4380 mm MIN. HEIGHT OF THE DIE (without dovetail):220 mm WEIGHT OF ANVIL: 24 T MAX. WEIGHT OF UPPER DIE: 400 Kg TOTAL WEIGHT OF THE HAMMER: 35 T
68	ID MA30805 Make M.I. KALININA Model M2145 YOM 1988 Condition Good Condition Photo See Photo Nominal mass of drop parts: 3150 kg Strike energy: 80 kJ Max number of blows per 1 min: 60 Max ram stroke: 1250 mm Distance clear between guides: 710 mm Ram front-to-back dimensions: 750 mm Die-holder front-to-back dimensions: 1000 mm Bottom die impression-to-floor distance: 800 mm Min die holder-to-ram distance: 340 mm Steam (air) pressure: 0.7-0.9 MPa Overall dimensions: -Floor space: 3820x1800 mm -Height above floor level: 5340 mm Weight without anvil: 25 ton Weight of anvil block: 63 ton Total weight of the hammer with anvil block: 88 ton
69	ID MA30640 Make Model YOM Condition Photo See Photo Air steam forging hammer type K05.501 Manufacturer: KALININ Factory Made in: Russia Strike energy: 40 kJ Nominal weight of the falling parts: 1600 kg Number of strokes per minute: 70 ± 10% Distance between guides in daylight: 520 mm Min. height of dies without shafts: 220 mm Max. height of dies without shafts: 460 mm Dimensions of die holder front-to-back: 620 mm Diameter of cylinder: 350 mm Diameter of rod: 125 mm Weight of upper die: -Min.: 85 kg -Max.: 200 kg Voltage: 360 V, 50 Hz Hammer dimensions: -Left-to-right: 3000 mm -Front-to-back: 1600 mm -Height over floor level: 4400 mm Hammer weight: 41000 kg
70	ID MA30633 Make Model MA2145 YOM Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons
71	ID MA30551 Make Model M2143 YOM Condition Photo See Photo Capacity : 2 tons, Max ram stroke : 1200 mm, Impact energy : 50 kJ, Max no of blows per min : 70, Distance clear between guides : 600 mm, Ram front-to-back dimensions : 670 mm, Die holder front-to-back dimensions : 900 mm, Bottom die impression-to-floor distance : 800 mm, Min. die holder-to-ram distance : 260 mm, Steam (air) pressure : 0.6 - 0.8 MPa, Overall dimensions : 3650 x 1660 x 5310 mm, Total weight : 50000 kg
72	ID MA30550 Make Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
73	ID MI6787 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity: 1 ton
74	ID MI6666 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity : 2 Ton, on foundation connected to pneumatic line and can take trial
75	ID MI6665 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity : 1 Ton,
76	ID MA29639 Make Huta Zygmunt,Polish Model MPM3000A YOM Condition Good Condition Photo See Photo Weight of the Machine 3570 Light between the guides 660 Length of the joint in the club 750 Length of the joint in the mold holder 1050 Minimum height of the molds (dovetail not included) 350 Maximum weight of the upper mold 1100 Height of the meeting line of the molds from the ground 765
77	ID MA29638 Make Huta Zygmunt,Polish Model MPM16000B YOM 1979 Condition Excellent condition,under power Photo See Photo Weight of the Anvil 6300 kg Energy 17500 Kgm Light Among the gulde 850 L.Jogance of the incestro net • stamp 1250 Minimum Atterts de escapes (annuity queue not included 400 Weight max. of the stamp Supt.:lore 1600
78	ID MA29631 Make Russian Model M212 YOM Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t.
79	ID MA29436 Make Huta Zygmunt,Polish Model MPM6300B YOM Condition Good Condition Photo See Photo Energy of blow : 7000 kg/m, Weight of falling ram : 2500 kg, Max. tup stroke : 850 mm, Guideway spacing : 650 mm, Min. height of die : 300 mm, Max. weight of upper die : 800 kg, Stroking rate : 100 s.p.m, Hight over floor : 4100 mm, Total hight : 5.145 mm, Total weight of hammer : 64 tons, Weight of anvil : 47,5 tons
80	ID MA29269 Make Kramatorsk Model 17KP YOM 1984 Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
81	ID MA28751 Make Russian Model M2145 YOM 1981 Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
82	ID MA28720 Make Erie Model YOM 1972/1985 Condition Good working condition Photo See Photo Capacity: 8 ton, Hit energy: 208(20,8) kJ, Weight of falling parts: 9000 kg, Impact frequency:~55±5 min-1, The minimum die height:600-100 mm, Ram size from front to back: 1020 mm, Anvil block insert size from to back : 1450 mm, Steam (Air) manometric pressure,MPa: 0,8(8) kg/cm2, Diameter of cylinder: 609,6 mm, Ram diameter: 216 mm
83	ID MA28585 Make Russian Model MA2147 YOM 1980 Condition Excellent Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
84	ID MA28468 Make Russian Model MA2147 YOM Condition Excellent Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
85	ID MA28363 Make Huta Zygmunt,Polish Model MPM25000 YOM Condition Excellent Photo See Photo Capacity : 8 tons, Stroke energy : 25000 kgm, Maximum stroke : 1100 mm, Light between guides : 850 mm, Stroke : 75 min, Ram Weight : 8060 mm, Shut height : 1400 mm, Die weight max : 2400 mm, Compressed Air : 5-7, Air consumption per hour : 2000 kg, Die of ram rod : 610 mm, Anvil block weight : 170 t. Total hammer weight : 225 t.
86	ID MA28306 Make Russian Model M2150 YOM 1970 Condition Good condition,under power Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
87	ID MA28278 Make TMP Voronezh Russia Model M2145 YOM 1990 Condition Very good condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
88	ID MI6266 Make Romanian Model CM1250 YOM 1979 Condition Good Condition Photo See Photo Capacity : 1 ton, Precussive energy : 3600 mkg, Ram weight : 1250 kg, Mode of operation pneumatic, Table size (front to back) : 700 mm, Stroke : 800 mm, Strokes : 10 min, Working pressure : 5-7 atm, Max. weight of upper die : 400 kg, Die height : 220 mm, Ram (front to back) : 500 mm, Air consumption : 15 m3/min, Anvil weight : 24 ton, Height of machine above floor : 3750 mm, Total machine height : 4380 mm, Total weight : 40 tons
89	ID MA28184 Make Russian Model M2150 YOM 1978 Condition Disassembled Photo See Photo Capacity: 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons. Available spares at extra cost.
90	ID MA28111 Make Kramatorsk Model MA2147 YOM Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons, Quantity No. : 2.
91	ID MI6223 Make Huta Zygmunt,Polish Model MPM1000 YOM Condition Good Condition Photo See Photo Capacity : 1 ton, Precussive energy : 3600 mkg, Ram weight : 1250 kg, Mode of operation pneumatic, Table size (front to back) : 700 mm, Stroke : 800 mm, Strokes : 10 min, Working pressure : 5-7 atm, Max. weight of upper die : 400 kg, Die height : 220 mm, Ram (front to back) : 500 mm, Air consumption : 15 m3/min, Anvil weight : 24 ton, Height of machine above floor : 3750 mm, Total machine height : 4380 mm, Total weight : 40 tons
92	ID MA27890 Make Russian Model M2145 YOM Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
93	ID MA27869 Make Stanko-Russia Model M2152 YOM 1978 Condition Good Condition Photo See Photo Nominal mass of drop parts : 16 ton, Impact energy : 400 kj, Maximum number of blows per minute : 20, Maximum ram stroke : 1500 mm, Distance clear between guides : 1180 mm, Ram front to back dimensions : 1500 mm, Die holder front to back dimensions : 1600 mm, Bottom die impression to floor distance : 500 mm, Minimum die holder to ram distance : 500 mm, Steam (air) pressure : 0.7 – 0.9 Mpa, Overall dimensions :- Floor space : 4500 x 2450 mm, Height above floor level : 7920 mm, Mass (less anvil block) : 95 ton. Mass of anvil block : 325 ton. Equipped with new main anvil, new rod and new small parts, Reconditioned upper guides and cylinder head.
94	ID MI6171 Make Huta Zygmunt,Polish Model YOM Condition Excellent condition,under power Photo See Photo Capacity: 6 ton, Analogue of Huta Zgmunt Hammer MPM 16000B Maximum energy of impact at maximum stroke : 17500 kgm, Maximum working stroke of ram : 1000 mm, Number of blows per minute : 90, Overall dimensions :- length : 4000 mm, width : 2400 mm, height : 7255 mm, Weight of machine : 181 tons Air tank 180 h.p. Compressors 3 nos
95	ID MA27520 Make Russian Model M2145 YOM Condition excellent working condition Photo See Photo 3 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons.
96	ID MA27457 Make Russian Model M2145 YOM Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons, weight: 89000 kg,quantity:2 nos
97	ID MA27361 Make Chambersburg Model YOM 1970 Condition Dismantled,Good condition Photo See Photo Capacity : 6 Tons, Stroke : 1295 mm. Blow Energy : 16,300 KGM, Machine Weight : 150 ton.
98	ID MA27293 Make Russian Model M2145 YOM 1993 Condition Good Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons
99	ID MA27103 Make Huta Zygmunt,Polish Model MPM3150B YOM Condition Good Condition Photo See Photo Capacity : 1 ton, Precussive energy : 3600 mkg, Ram weight : 1250 kg, Mode of operation pneumatic, Table size (front to back) : 700 mm, Stroke : 800 mm, Strokes : 10 min, Working pressure : 5-7 atm, Max. weight of upper die : 400 kg, Die height : 220 mm, Ram (front to back) : 500 mm, Air consumption : 15 m3/min, Anvil weight : 24 ton, Height of machine above floor : 3750 mm, Total machine height : 4380 mm, Total weight : 35 ton.
100	ID MA27092 Make Erie Model YOM 1980 Condition Very good condition Photo See Photo Capacity : 12.5 tons, Ram Stroke : 1450 mm, Distance between columns : 1000 mm, Ram F-B : 1500 mm, Saw block F-B : 1750 mm, Die space (Ram down) : 500 mm, Cylinder bore : 750 mm, Inlet : 200 mm, Exhaust : 250 mm, Height above floor : 7100 mm, Weight : 412 tons
101	ID MI6060 Make Hungarian Model CM6300 YOM Condition Excellent,Fully reconditioned Photo See Photo Analogue of Huta Zgmunt Hammer MPM 16000B Capacity : 6.3 tons, Maximum energy of impact at maximum stroke : 17500 kgm, Maximum working stroke of ram : 1000 mm, Number of blows per minute : 90, Overall dimensions :- length : 4000 mm, width : 2400 mm, height : 7255 mm, Weight of machine : 181 tons One extra set of all essential spares are also available for the complete hammer.
102	ID MA26916 Make Erie Model YOM Condition Dismantled,Good condition Photo See Photo Capacity : 17.5 ton, Weight of Ram, Rod and Piston : 35,000 lbs, Stroke of Ram : 1500 mm, Distance Between Columns/Guides : 1100 mm, Ram F-B : 2000 mm, Saw Block F-B : 2250 mm, Cylinder Bore : 825 mm, Inlet : 175 mm, Exhaust : 225 mm, Height above Floor : 23.5 ft, Depth below floor line with timbers : 18 ft. Ram, Mid Sub-Base wt 180K, Anvil wt 340K, Bottom Sub wt 220K, Crown & Cylinder, Tie Plate, Two Columns, Rod & Piston, Leg bolts and linkage in container of parts.
103	ID MA26875 Make TMP Voronezh Russia Model M213 YOM Condition retrofitted completely Photo See Photo 3.15 tons, Impact energy 8000 kgf-m, Max. working stroke of ram 1250 mm, no. of die strokes 60 per min., distance clear between guideways 710 mm, ram dimensions (F-B): 800 mm, dimensions of die holder (F-B): 1000 mm, Min. distance from ram to die-holder 340 mm, Steam (air) pressure from ram to die holder 7-9 mm, overall dimensions: 4100 x 1900 x 5780 mm, weight of anvil 63 tons, total weight of hammer 89 tons.
104	ID MA26867 Make Huta Zygmunt,Polish Model MPM3150B YOM Condition Good Condition Photo See Photo Capacity : 1ton, Energy : 3600 kgm, Weight of the ram : 1250 kg, Max. slide stroke : 800 mm, Light on the guide : 550 mm, Weight max up die : 400 kg, Stroke : 110 min, Weight chabotte without die holder : 24 ton, Total weight : 35 ton.
105	ID MI6035 Make Model YOM Condition Good Condition Photo See Photo One piece steam hammer fabricated of force approx x 7000 kgs, One pc trolley for handling hot metal in forged shop, Three set ram, Five pieces ram part, Platform over machinery for mantainance, Anvil 21 tonns (key way system) - 1 no, Anvil block : 2 pcs, Base plate : 1 no, Baseplate log 17' - 1 set, One piece tank (2nd hand railway) for stroing oil appx. capacity 30 kl, One piece hydra capacity 9 mt, One piece compressor 10.5 kg, One no. tank for string compresses air, Few main switches and wires, Tongs and other manufacturing required few items.
106	ID MA26836 Make Russian Model M2150 YOM Condition Good Condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180x1180 mm, Surface die support 1320x1320 mm, Overall dimensions 4400x2700x7238mm, Weight of the base 200 ton, Total weight 284 tons. With 2 spare columns.
107	ID MI6033 Make Banning Model GOA3205 YOM Condition Dismantled,Good condition Photo See Photo Capacity : 2 ton Quantity : 2 nos
108	ID MI6026 Make Erie Model YOM Condition Dismantled,Good condition Photo See Photo Capacity : 2 ton, Ram Piston Rod Weight : 2668 kgs, Cylinder diameter : 375 mm, Air steam : 110 PSIG, Mean effective steam air : 75 PSIG, Actual ram stroke : 1250 mm, Penetration of material : 3.125 mm, Air force : 6012 kg, Impact energy : 99.92 KJ Anvil Weight - 36 tons Other items (columns, ram, cylinder, one set of die block and extra sow block) 22 tons
109	ID MA26768 Make TMP Voronezh Russia Model M2143 YOM 1986 Condition Good Condition Photo See Photo Capacity : 2 tons, Max ram stroke : 1200 mm, Impact energy : 50 kJ, Max no of blows per min : 70, Distance clear between guides : 600 mm, Ram front-to-back dimensions : 670 mm, Die holder front-to-back dimensions : 900 mm, Bottom die impression-to-floor distance : 800 mm, Min. die holder-to-ram distance : 260 mm, Steam (air) pressure : 0.6 - 0.8 MPa, Overall dimensions : 3650 x 1660 x 5310 mm, Total weight : 50000 kg,
110	ID MA26717 Make Russian Model M2143 YOM 1977 Condition working condition ,under power Photo See Photo Weight of falling part : 2 tons impact energy : 50 kj, Max no.of blows : 70 per minute, Max ram stroke : 1200 mm, distance clear between guides : 600 mm, ram front to back dimensions : 670 mm, die holder front to back dimensions : 900 mm, bottom die impressions to floor distance : 800 mm, minimum die holder to ram distance : 260 mm, steam(air)pressure,0.6-0.8 MPa, Overall dimensions : floor space 3650 x 1660 mm, height above floor lavel 5310 mm, mass(less anvil block)approx.18t, mass anvil block apporx 40t, Total weight 58 tones.
111	ID MA26715 Make SKMZ Model 18KP YOM 1978 Condition Good Condition Photo See Photo Capacity 10 tons,nominal mass of drop parts without upper instr.:9 tons, effective working kinetic energy after blow 25000 kg mtr., max. working ram stroke 1400 mm, max no of blows 30/min , distance between slides 1000 mm, shut height 775 mm , ram size front to back 1200 mm , bolster size front to back 1200 mm , air pressure 7-9 MPA ,height of instruments 450 min.,die-holder front to back dimensions: 1400 mm,height above floor level: 7270 mm, hammer dimensions 4400x10420x2700 mm,mass (less anvil block): 75 ton, weight 205 tons.
112	ID MA26714 Make Russian Model 28KP YOM 1978 Condition Good Condition Photo See Photo Capacity : 16 tons, Nominal mass of drop parts, kg 16,000 Impact energy, kj. 400 Maximum number of blows per minute 20 Maximum ram stroke, mm 1,500 Distance clear between guides, mm 1,180 Ram front to back dimensions 1,500 Die holder front to back dimenstions, mm 1,600 Bottom die impression to floor distance, mm 500 Minimum die holder to ram distance, mm 500 Steam (air) pressure, Mpa 0.7 – 0.9 Overall dimensions, mm: Floor space 4,500 x 2,450 Height above floor level 7,920 Mass (less anvil block), t, approx 95 Mass of anvil block, to, approx 325 Electrics: Power supply 380 volts 3 phase 50 cycles
113	ID MA26547 Make Russian Model M2145 YOM 1986 Condition Good Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons
114	ID MA26479 Make Huta Zygmunt,Polish Model MPM1600B YOM 1980 Condition Good Condition Photo See Photo Ram stroke : 750 mm, Energy of full blow : 1840 kgm, Quantity of stroke : 120 u/min, Mass of anvil block : 12,5 t, Mass of hammer with anvil block : 21,9 t.
115	ID MA25836 Make Huta Zygmunt,Polish Model MPM1600B YOM Condition Good Condition Photo See Photo Energy of blow : 1840 kg, Max tup stroke : 750 mm, Guideway spacing : 450 mm, Length of die seat in the tup : 400 mm, Length of die seat in the die holder : 600 mm, Min height of the die : 180 mm, Max weight of upper die : 200 kg, Min height of die partition above floor : 800 mm, Number of blows per minute : 120, Steam or incoming air pressure : 5-7 atm, Average steam consumption : 380 kg/h, Average air consumption : 7m3 / min, Height of hammer above floor : 3440 mm, Total height of hammer : 3850 mm, Weight of anvil block without die holder : 12,5 ton, weight of hammer with anvil block : 18,5 ton.
116	ID MA25835 Make Huta Zygmunt,Polish Model MPM3150B YOM Condition Very good condition Photo See Photo Energy of blow : 3600 kg, Weight of tup (without die) : 1250 kg, Maxi stroke : 800 mm, Distance between guides : 550 mm, Length of die seat in the die holder : 700 mm, Length of die seat in the tup : 500 mm, Mini height of dies (without dovetail) : 220 mm, Maxi weight of upper die : 400 kg, Height of die partition above floor : 800 mm, Number of stroke per minute : 110, Steem incoming pressure : 5-7kg / cm2, Steem hourly consumption : 650 kg/h, Consumption of compressed air : 12 m3 / mn, Hole of cylinder : 410 mm, Weight of the anvil (without die holder) : 24 ton, Weight of machine : 35 ton.
117	ID MA25187 Make Russian Model M211 YOM 1974 Condition Good working condition Photo See Photo 1 ton, max travel of ram 1200 mm, distance between column 560 mm, distance between guides 500 mm, 80 SPM , min. height of die upper 110 mm, lower 110 mm, cylinder dia 280 mm, piston rod dia 120 mm, air steam pressure 7=9 atmospheres, min. height of die 220 mm, saw block height 660 mm, weight of anvil block 20.37 tons , hammer weight 30.7 tons , dimensions 2380 x 1390 x 5045 mm.
118	ID MA24726 Make Kramatorsk Model MA2147 YOM 1984 Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons.
119	ID MA24603 Make Kramatorsk Model 18KP YOM 1984 Condition Good working condition Photo See Photo 10 tons weight of falling part,nominal mass of drop parts without upper instr.:9 tons, effective working kinetic energy after blow 25000 kg mtr., max. working ram stroke 1400 mm, max no of blows 30/min , distance between slides 1000 mm, shut height 775 mm , ram size front to back 1200 mm , bolster size front to back 1200 mm , air pressure 7-9 MPA ,height of instruments 450 min.,die-holder front to back dimensions: 1400 mm,height above floor level: 7270 mm, hammer dimensions 4400x10420x2700 mm,mass (less anvil block): 75 ton, weight 205 tons.
120	ID MA24402 Make Russian Model M212 YOM Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t
121	ID MA24302 Make Russian Model M2147 YOM 1982 Condition Complete Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
122	ID MA23966 Make Russian Model M211 YOM 1970 Condition Good working condition Photo See Photo 1 ton, max travel of ram 1200 mm, distance between column 560 mm, distance between guides 500 mm, 80 SPM , min. height of die upper 110 mm, lower 110 mm, cylinder dia 280 mm, piston rod dia 120 mm, air steam pressure 7=9 atmospheres, min. height of die 220 mm, saw block height 660 mm, weight of anvil block 20.37 tons , hammer weight 30.7 tons , dimensions 2380 x 1390 x 5045 mm.
123	ID MA23962 Make Russian Model M2145 YOM 1985 Condition Good working condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons
124	ID MI5689 Make Kramatorsk Model M2150 YOM Condition Very good condition Photo See Photo Weight of falling parts 10 Tons, Working energy 26000 mkg., Max. number of strokes per minute 30, Max. ram stroke 1400 mm, Distance between guides 1000 mm, Ram dimensions front-to-back 1180 mm, Die holder dimensions front-back 1320 mm, Bottom die impression-to-floor distance 600 mm, Min. die holder-to-ram 450 mm, Air pressure 07-0.9 Mpa, Dimensions 4400 x 2700 mm, Height above floor 7238 mm, Weight of hammer without anvil 84 tons Weight of anvil 200 tons
125	ID MA23686 Make Russian Model M2150 YOM 1978 Condition Dismantled,Good condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180x1180 mm, Surface die support 1320x1320 mm, Overall dimensions 4400x2700x7238mm, Weight of the base 200 ton, Total weight 284 tons.
126	ID MA23028 Make Huta Zygmunt,Polish Model MPM3150 YOM Condition Good Condition Photo See Photo Weight 1250 Kg Blows Energy 3600 Kg Stroke Max Ram 800 Mm Light 550 Mm Height Min. 220 Mm Weight Max Inferior Die 400 Kg Stroke Minute 110 Steam Pression 5-7 Kg/Cm² Air Pression 5-7 Kg/Cm² Consumption Air Pression On Minute 12 M³/Mn Roll Bore 410 Mm Chabotte Weight 24 Ton Weight Hammer 35 Ton
127	ID MA22895 Make Russian Model M2147 YOM 1982 Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
128	ID MA22746 Make TMP Voronezh Russia Model M213 YOM 1972 Condition Dismantled,Good condition Photo See Photo 3,15 tons, Impact energy 8000 kgf-m, Max. working stroke of ram 1250 mm, no. of die strokes 60 per min., distance clear between guideways 710 mm, ram dimensions (F-B): 800 mm, dimensions of die holder (F-B): 1000 mm, Min. distance from ram to die-holder 340 mm, Steam (air) pressure from ram to die holder 7-9 mm, overall dimensions: 4100 x 1900 x 5780 mm, weight of anvil 63 tons, total weight of hammer 89 tons
129	ID MI5574 Make Zdas Model YOM Condition Dismantled,Good condition Photo See Photo Capacity : 2 tons, Energy of blow 7000 KGM, Max stroke 800 mm, Guide way spacing 665 mm, Length of die seat in the tup 590 mm, Length of die seat in the holder 790 mm, Minimum height of dies (without tail) 300 mm, Maximum die height 700mm, Minimum height of die partition above floor 900 mm, Number of blows per minutes 90 Nos. Steam or including air pressure 5 to 7 kg/cm2, Average air consumption 900 cfm.
130	ID MA22440 Make Russian Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
131	ID MA22044 Make Russian Model K05.501 YOM 1983 Condition Good Condition Photo See Photo 1.6 tons, blow energy 40(4), mass of falling part 1600 tons , number of blows per min 70:10% , height : max 460 mm , min 220 mm , ram size 540 mm , distance between columns 520 mm , bolster size 620 mm.die block size 600 mm, anvil weight 32 tons , total weight 41 tons.
132	ID MA22022 Make Russian Model MA2143 YOM 1978 Condition Good Condition Photo See Photo 2 tons: impact energy 50kj, Max no.of blows 70 per minute, Max ram stroke 1200mm, distance clear between guides 600mm, ram front to back dimensions 670mm, die holder front to back dimensions 900mm, bottom die impressions to floor distance 800mm, minimum die holder to ram distance 260mm, steam(air)pressure,0.6-0.8MPa, Overall dimensions: floor space 3650x1660mm, height above floor lavel 5310mm, mass(less anvil block)approx.18t, mass anvil block apporx 40t, Total weight 58 tones.
133	ID MI5531 Make Beche Model 4KGL YOM 1982 Condition Absolutely New Photo See Photo Capacity 4 tons, Ram thickness 500 mm, height 600 mm, Die Blockap: between pillar 700 mm, Input energy 40kj, Ram dia. 480 mm, Air receiver tank : 14 feet x 5.5 feet, with all pipe line & other accessories.
134	ID MA21543 Make Huta Zygmunt,Polish Model MPM3150B YOM 1974 Condition Excellent condition,under power Photo See Photo percussive energy 3600 mkg , stroke 800 mm , 110 SPM , ram weight 1250 kg , ram (front to back) 500 mm , die height 220 mm , anvil weight 24 tons , machine height above floor 3750 mm , total weight 35 tons.
135	ID MA21270 Make Huta Zygmunt,Polish Model MPM1600B YOM 1975 Condition Good Condition Photo See Photo Energy of blow 18.4 kJ, weight of falling part (without die)690 kg, max weight of upper die 200 kg, weight of anvil block without die holder 12.5 tons, weight of hammer with anvil block 22 tons , approx forging weight 0.5-1 kg, steam of incoming pressure 0.5-0.7 MPA, average steam consumption 380 kg/h., average air consumption : cold air 10 m3/min , hotair 7 m3/min, number of blows 120/min, Overall dimensions: 2100 x 1185 x 3850 mm, height of hammer above floor 3440 mm, min. height of die partition above floor 800 mm, min height of die (without tail) 180 mm, Working area : guideway spacing 418 mm, length of die seal in tup 400 mm, length of seat in die holder 600 mm, max width of working area 450 mm, max tup stroke 750 mm
136	ID MA21269 Make Huta Zygmunt,Polish Model MPM1600B YOM 1975 Condition Good Condition Photo See Photo Energy of blow 18.4 kJ, weight of falling part (without die)690 kg, max weight of upper die 200 kg, weight of anvil block without die holder 12.5 tons, weight of hammer with anvil block 22 tons , approx forging weight 0.5-1 kg, steam of incoming pressure 0.5-0.7 MPA, average steam consumption 380 kg/h., average air consumption : cold air 10 m3/min , hotair 7 m3/min, number of blows 120/min, Overall dimensions: 2100 x 1185 x 3850 mm, height of hammer above floor 3440 mm, min. height of die partition above floor 800 mm, min height of die (without tail) 180 mm, Working area : guideway spacing 418 mm, length of die seal in tup 400 mm, length of seat in die holder 600 mm, max width of working area 450 mm, max tup stroke 750 mm
137	ID MA21268 Make Huta Zygmunt,Polish Model MPM1600B YOM 1975 Condition Good Condition Photo See Photo Energy of blow 18.4 kJ, weight of falling part (without die)690 kg, max weight of upper die 200 kg, weight of anvil block without die holder 12.5 tons, weight of hammer with anvil block 22 tons , approx forging weight 0.5-1 kg, steam of incoming pressure 0.5-0.7 MPA, average steam consumption 380 kg/h., average air consumption : cold air 10 m3/min , hotair 7 m3/min, number of blows 120/min, Overall dimensions: 2100 x 1185 x 3850 mm, height of hammer above floor 3440 mm, min. height of die partition above floor 800 mm, min height of die (without tail) 180 mm, Working area : guideway spacing 418 mm, length of die seal in tup 400 mm, length of seat in die holder 600 mm, max width of working area 450 mm, max tup stroke 750 mm
138	ID MI5396 Make Erie Model PA615 YOM Condition overhauled Photo See Photo Falling weight: 8 tons (16,000 lbs),Impact Energy-18,800 kg force/mtr, Ram Stroke: 1346 mm, Cylinder dia- 622.3 mm, distance between guides- 915 mm, hammer weight: 204 tons
139	ID MI5385 Make Huta Zygmunt,Polish Model MPM1000 YOM Condition excellent working condition Photo See Photo energy of blow 3500 mkg , weight of falling parts 1230 kg , stroke max 900 mm , guide way spacing 460 mm , length of die seat in tup 460 mm, length of die seat in holder 700 mm, maxweight of upper die 400 kg, 110 SPM , steam consumption 650 kg/h, compresses air cosumption 12m3/min , anvil weight 22,5 tons, total weight 34,3 tons.
140	ID MA20318 Make Huta Zygmunt,Polish Model MPM1000 YOM 1984 Condition Good Condition Photo See Photo energy of blow 3500 mkg , weight of falling parts 1230 kg , stroke max 900 mm , guide way spacing 460 mm , length of die seat in tup 460 mm , length of die seat in holder 700 mm , maxweight of upper die 400 kg , 110 SPM , steam consumption 650 kg/h , compresses air cosumption 12m3/min , anvil weight 22,5 tons , total weight 34,3 tons.
141	ID MA19791 Make Kramatorsk Model M2147 YOM 1984 Condition Complete ,good working condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
142	ID MA19469 Make Erie Model YOM Condition Good Condition Photo See Photo 6 tons capacity(12000 pounds)
143	ID MA19396 Make Russian Model M311 YOM Condition Good Condition Photo See Photo aa
144	ID MA19395 Make Russian Model M212 YOM Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t
145	ID MA19394 Make Russian Model M211 YOM Condition Good Condition Photo See Photo 1 ton, max travel of ram 1200 mm, distance between column 560 mm, distance between guides 500 mm, 80 SPM , min. height of die upper 110 mm, lower 110 mm, cylinder dia 280 mm, piston rod dia 120 mm, air steam pressure 7=9 atmospheres, min. height of die 220 mm, saw block height 660 mm, weight of anvil block 20.37 tons , hammer weight 30.7 tons , dimensions 2380 x 1390 x 5045 mm.
146	ID MA19158 Make Huta Zygmunt,Polish Model MPM2000A/6300B YOM Condition can be inspected under power Photo See Photo Ram weight: 2100 kg, Ram stroke: 850 mm, Energy of full blow: 6300 kgm, Quantity of stroke: 100,
147	ID MA19111 Make Lasco Model HOU200 YOM Condition Brand New Photo See Photo Blow energy 20 kJ, Blow frequency at max. energy 95 1/min, Ram velocity max. 5 mm, Max. ram stroke 660 mm, min. ram stroke 480 mm, Ram depth : 500 mm, Ram weight 1500 kg., Die height max. combined upper and lower, excluding dove tails 360 mm, Die height min. combined upper and lower excluding dove-tails 180 mm, Daylight between guides 580 mm, Frame breadth 2290 mm, Frame depth 1400 mm, Frame weight 25500 kg., Total machine weight 37500 kg., Height above floor level - assuming insert height 700 mm : 4300 mm, total machine height 5100 mm, Electrical equipment : Main motor capacity 45 kW, Cooling motor capacity 1,1 kW, Lubrication pump capacity 0,18 kW, Supply voltage 380 V 50 Hz, Control voltage 230 V 50 Hz, Valve voltage 24 V DC, Protection (drive)IP 55, Protection (control) IP 55.
148	ID MA18950 Make Huta Zygmunt,Polish Model MPM1600B YOM 1978 Condition Good Condition Photo See Photo Ram stroke: 750 mm, Energy of full blow: 1840 kgm, Quantity of stroke: 120 u/min, Mass of anvil block: 12,5 t, Mass of hammer with anvil block: 21,9 t.
149	ID MA18949 Make Huta Zygmunt,Polish Model MPM3150B YOM 1978 Condition Good Condition Photo See Photo Mass of falling parts: 1000 kg, Ram stroke: 800 mm, Energy of full blow: 3600kgm, Quantity of stroke: 110, Mass of hammer: 35t. Qty : 2 Nos.
150	ID MA18948 Make Huta Zygmunt,Polish Model MPM1000A YOM Condition Good Condition Photo See Photo Energy of blow: 3500 kg, Weight of falling parts(without dies):1150 kg, Max tup stroke: 900 mm, Guideway spacing: 460 mm.110 blows/min., Weight: 35t.
151	ID MA18947 Make Huta Zygmunt,Polish Model MPM2000A/6300B YOM Condition Good Condition Photo See Photo Ram weight: 2100 kg, Ram stroke: 850 mm, Energy of full blow: 6300 kgm, Quantity of stroke: 100,
152	ID MA18946 Make Huta Zygmunt,Polish Model MPM2000/6300B YOM 1978 Condition Good Condition Photo See Photo Ram weight: 2100 kg, Ram stroke: 850 mm, Energy of full blow: 6300 kgm, Quantity of stroke: 100, Mass of hammer: 17t (without anvil block).
153	ID MA18944 Make Huta Zygmunt,Polish Model MPM6300A YOM Condition excellent working condition Photo See Photo Weight 2500 kg, Blows energy 7000 kgm, Stroke max ram 850 mm, Light 650 mm, Height min.300 mm, Weight max inferior die 800 kg, Stroke minute 100, Steam pression 5-7 kg/cm, Air pression 5-7 kg/cm, Consumption air pression on minute 18 mcub/mn, Roll bore 540 mm, Chabotte weight 47,5 ton, Weight hammer 64 ton.
154	ID MI5150 Make Huta Zygmunt,Polish Model MPM3000 YOM Condition Good Condition Photo See Photo 1.25 tons
155	ID MA18391 Make Chinese Model YOM Brand New Condition Brand New Photo See Photo 400 kg
156	ID MA18390 Make Chinese Model YOM Brand New Condition Brand New Photo See Photo 560 kg
157	ID MA18389 Make Chinese Model YOM Brand New Condition Brand New Photo See Photo 750 kg
158	ID MA18191 Make Russian Model M2147 YOM 1982 Condition Dismantled Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
159	ID MA18002 Make Massey,UK Model YOM 1990 Condition Good Condition Photo See Photo Weight of falling part 500 kg, Overall weight 20 tons.
160	ID MA17999 Make Morgan Model YOM Condition Good Condition Photo See Photo Weight of falling part 1500 kg, Overall weight 40 tons.
161	ID MA17985 Make Russian Model M2147 YOM 1984-86 Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
162	ID MA17860 Make Kramatorsk Model 17KP YOM 1974 Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , upper anvil weight 77 tons & lower anvil 23 tons. + Trimming Press KB9534 (250 tons) + Conveyor
163	ID MA17821 Make Russian Model M2150 YOM 1985 Condition Good working condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180x1180 mm, Surface die support 1320x1320 mm, Overall dimensions 4400x2700x7238mm, Weight of the base 200 ton, Total weight 284 tons.
164	ID MA17818 Make Russian Model M2147 YOM 1985 Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
165	ID MA17473 Make Kramatorsk Model 17KP YOM 1974 Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
166	ID MA17398 Make NKMZ Kramatorsk Model YOM Brand New Condition Brand New Photo See Photo blow energy 200 kj , rated falling weight 8 tons , max ram stroke 1400 mm, min. die height (w/o) dovetails) 450 mm, number of blows 55+_5 per min , clearance between guides 920 mm, ram length 1180 mm, sow block length 1320 mm, pressure of air or steam (gauge) 0.6.0.7 MPa , the charge of energy carrier for a cycle 5,8 m3 normal , overall dimensions L-R 4400 mm, F-B 2200 mm, height of hammer above floor 7030 mm, distance from floor level to die parting plane 800 mm, piston rod height above floor at disassembly 10200 mm.
167	ID MA17303 Make Russian Model M2147 YOM Condition Good working condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
168	ID MA17174 Make Russian Model M211 YOM 1956 Condition Complete Photo See Photo 1 ton, max travel of ram 1200 mm, distance between column 560 mm, distance between guides 500 mm, 80 SPM , min. height of die upper 110 mm, lower 110 mm, cylinder dia 280 mm, piston rod dia 120 mm, air steam pressure 7=9 atmospheres, min. height of die 220 mm, saw block height 660 mm, weight of anvil block 20.37 tons , hammer weight 30.7 tons , dimensions 2380 x 1390 x 5045 mm.
169	ID MA16988 Make Huta Zygmunt,Polish Model MPM6300B YOM Condition Good Condition Photo See Photo Percussive energy : 7000 mkg, Stroke : 850 mm, Stroke/min : 100 (max.), Ram weight : 2496 kg, Die height : 300 mmt, Height of machine above floor : 4100 mm, Total weight : 75 tons, Mode of operation : Pneumatic. Pneumatic working pressure : 0.5-0.7 bar.
170	ID MA16565 Make Romanian Model CM1250 YOM Condition Good Condition Photo See Photo maximum energy of impact at maximum stroke 3600 kgm ram weight : 1250 mkg maximum working stroke of ram : 800 mm number of blows per minute : 110 nominal working pressure : 5 – 7 bar Overall dimension : Length : 2600 mm, Width : 1300 mm, Height : 4380 mm, weight : 35 tons
171	ID MA16564 Make Romanian Model CM3150 YOM Condition Good Condition Photo See Photo maximum energy of impact at maximum stroke 10000 mkg ram weight: 3150mkg maximum working stroke of ram : 900 mm number of blows per minute : 90 nominal working pressure : 5 – 7 bar Overall Dimensions : length : 3300 mm, Width : 2000 mm, Height : 5885 mm weight : 96000 kg.
172	ID MA13884 Make Russian Model M2150 YOM 1982 Condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180x1180 mm, Surface die support 1320x1320 mm, Overall dimensions 4400x2700x7238mm, Weight of the base 200 ton, Total weight 284 tons.
173	ID MA13801 Make Russian Model MA2147 YOM 2005 Condition Brand New Photo See Photo 5 tons , blow energy 125 kJ , dropping part weight 5 tons , blow frequency at nominal working capacity 65/min , ram stroke 1300 mm , ram depth 950 mm , area of forged piece 1250 cm2 , die height without dovetails 400 mm , datlight between guides 800 mm , overall dimensions 4000 x 2000 x 6570 mm , height above floor to die opening area 800 mm , mass of anvil stand 99,4 tons , mass of hammer without anvil stand 40,9 tons , overall weight 140,3 tons.
174	ID MA13734 Make Russian Model M2145 YOM 1985 Condition Good Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, mass (less anvil block) 25 tons , mass of anvil block 63 tons
175	ID MI4763 Make Chambersburg Model YOM Condition Good Condition Photo See Photo 1 Ton (2000 pounds), Stroke 1150 mm, Between guides 475 mm, Ram(front to back)500 mm, Anvil cap(front to back) 650 mm, Inlet 50 mm, Exhuast 50mm.
176	ID MI4762 Make Chambersburg Model YOM Condition Good Condition Photo See Photo 1.3 Tons, Stroke 1175mm, Between guide 500mm, Ram (front to back)525mm, Anvil cap(front to back) 675mm, Inlet 50mm, Exhust 75mm.
177	ID MA12846 Make Huta Zygmunt,Polish Model MPM1000A YOM Condition Good Condition Photo See Photo energy of blow 3500 mkg , weight of falling parts 1230 kg , stroke max 900 mm , guide way spacing 460 mm , length of die seat in tup 460 mm , length of die seat in holder 700 mm , maxweight of upper die 400 kg , 110 SPM , steam consumption 650 kg/h , compresses air cosumption 12m3/min , anvil weight 22,5 tons , total weight 34,3 tons.
178	ID MA12693 Make Russian Model M2147 YOM Condition Good condition,under power Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
179	ID MA7679 Make Russian Model M2145 YOM Condition Brand New Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, total weight 88 tons