Menu
Home
Sell Machines
Hot Deals
Contact
Main Site
VKengg.co.in
Category : Forging Equipment
Sub-Category : Part Former Hot
Total Machines Found :
51
Select
| Machine Details
1
ID
MA38241
Make
Hatebur
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
|
See Video
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 30000 kg
motor power 55 kW
measurements L:420 x H:210 x B:220 cm
2
ID
MA38240
Make
Hatebur
Model
AMP20
YOM
Condition
Good Condition
Photo
See Photo
Number of Forming Stations: 3
Total Forging Pressure: 900kn
#1 Station Forging Pressure: 400kn
#2 Station Forging Pressure: 70kn
#3 Station Forging Pressure: 400kn
Continual Drive Motor Power: 30.0kW
SPM Variable Drive: 120-180rpm
Machine Weight with Main Motor: 11.5T
Length with Drive Motor: 3430mm
Width: 2710mm
Height: 1550mm
Bar Feed Height from Floor: 800mm
Ram Stroke: 110mm
Maximum KO Stroke ( Die): 55mm
Feed Length ( theoritecal): 45mm
Die Diameter: SEE BELOW:
1st Station: 80mm
2nd Station: 100mm
3rd Station: 80mm
Maximum Punch Diameter when Piercing Hole: SEE BELOW:
1st Station: 75mm
2nd Station: 75mm
3rd Station: 75mm
WORKING RANGE :: SEE BELOW
Max./Min. Bar Diameter: 28mm/14mm
Cutoff Length: 15-40mm
Max. Forging Diameter: 38mm
Max. Across Flat Hex: 36mm
Max. Across Flat Square: 27mm
Electrics: Primary Power: 3 x 220 Volts/ 60Hz +/- 10%
3
ID
MA38198
Make
Hatebur
Model
AMP30
YOM
1973/2016
Condition
Good Condition
Photo
See Photo
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 35800 kg
motor power 55 kW
4
ID
MA38195
Make
Hatebur
Model
AMP20S
YOM
2005
Condition
Good Condition
Photo
See Photo
thread diameter 38 mm
max. width acros flats 36 mm
max. outside dia. of round pieces 38 mm
bar dia. 14-25 mm
cutting length 15-40 mm
press power 900 kN
number of forming stations 3
output - pieces/min 120-180
weight 11.5 t
motor power 24 PS
5
ID
MA38194
Make
Hatebur
Model
AMP70
YOM
year of construction 1976
Condition
Good Condition
Photo
See Photo
diameter range 120 mm
max. width across flats 85/105 mm
max. outside dia. of round pieces 120 mm
bar dia. 36 - 75 mm
cutting length 45 - 135 mm
number of forming stations 4
press power 1200 t
output - pieces/min 35 - 70
weight 165.000 kg
6
ID
MA38159
Make
Hatebur
Model
AMP70
YOM
1996
Condition
Good Condition
Photo
See Photo
- Overall strenth of molding : 15.000 kN
- Number of forming stations : 4
- Min. and Min. speed of the crankshaft : 50 χ 75 min-1
- Torque clutch, referring to the crankshaft : 450.000 Nm
- Maximum diameter of the raw material : 75 mm
- Cut-off length : 50 χ 150 mm
- Maximum forging weight range : 0.4 χ 5.0 kg
- Contunuous derive motor rating : 350 kW
- Main voltage : 3 x 400 V +/- 10%; 50 / 60 Hz
- Machine dimensiosn : 13.600 x 9.600 x 4.450(H) mm
2. Newelco 5100 kW induction heating system
- Medium freqeuncy induction heater
- Bar rack
7
ID
MA37921
Make
National
Model
7-4
YOM
Condition
Good Condition
Photo
See Photo
NUMBER OF FORMING DIES: 4
PRODUCTION RATE: 45- 70 PPM
FORGING TONNAGE: 1500 TONS
MAX WEIGHT OF PART: 14.3 LBS
MAX CUTOFF DIAMETER: 76 MM
MAX CUTOFF LENGTH: 155MM
MAX DIE KICKOUT: 155MM
MAX PUNCH KICKOUT: 70MM
PART OUTER DIAMETER: 165MM
1ST DIE DIAMETER: 228MM
2ND 3RD 4TH DIE DIAMETER: 298MM
1ST 2ND 3RD 4TH PUNCH DIAMETER: 222MM
MAIN MOTOR: 370KW
NET WEIGHT: 495.000 LBS
COMPLETE WITH: FULLY ADJUSTABLE FOUR FEED ROLL BOX / FEED ROLL REVERSING
PNEUMATICALLY CONTROLLED FEED ROLL GRIPPING PRESSURE / INFINITY VARIABLE ADJUSTMENTS OF STOCK GAGE WITH LENGTH READ OUT / WATER COOLED QUILL.DIE
PUNCHES.FEED ROLLS AND FEED ROLLER SHAFT / INDIVIDUALLY ADJUSTABLE DIE KICKOUTS / OVERLOAD RELIEF ON EACH DIE KICKOUT LEVER/ INDIVIDUAL DIE CAPS/INDIVIDUALLY ADJUSTABLE PUNCH HOLDERS/ INDIVIDUAL ADJUSTMENT OF PUNCH SHUT HEIGHT/ RAPID KICKOUT SLEEVE ADJUSTOR WITH HYDRAULIC LOCKNUTS /FULLY TIMED TRANSFER DRIVE USING STRAIGHT-LINE VERTICAL OPENING AND CLOSING/TRANSFER SETUP FIXTURE/ RECIRCULATING OIL LUBRICATION SYSTEM
8
ID
MA37756
Make
Hatebur
Model
AMP30
YOM
1968
Condition
Good Condition
Photo
See Photo
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 30000 kg
motor power 55 kW
measurements L:420 x H:210 x B:220 cm
9
ID
MA37745
Make
Hatebur
Model
AMP30
YOM
1974
Condition
Good Condition
Photo
See Photo
For parts of max. diameter: 64mm
- Max. across flats for hex nuts: 56mm
- Initial weight: 50 700g
- Max. bar diameter: 40mm
- Forming stations: 3
- Max. production per minute: 140
Including:
separating table and roll feeder
Induction heater 1250kW
Sort out conveyors
10
ID
MA36728
Make
Hatebur
Model
AMP30
YOM
1968
Condition
Good Condition
Photo
See Photo
|
See Video
diameter range: 64 mm
max. width across flats: 56 mm
max. outside dia. of round pieces: 64 mm
bar dia.: 18-40 mm
cutting length: 20-72 mm
output pieces/min: 140
number of forming stations: 3
press power: 230 t
11
ID
MA36360
Make
Russian
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
copy of hatebur, Russian make machine similar to amp30
12
ID
MA36227
Make
Hatebur
Model
AMP70
YOM
1976
Condition
Good Condition
Photo
See Photo
|
See Video
Hotmatic Hot Former with 5000KW Bar Heater & Bar Rack
NUMBER OF FORGING STATIONS 4
PRODUCTION RATE 50-70 PPM
MAX PART WEIGHT 13.4 POUNDS
MAX OUTER DIAMETER 125MM
MAX WIDTH ACROSS FLATS (HEX) 105MM
BAR DIAMETER MIN / MAX 36 60MM
CUTOFF LENGTH /MIN / MAX 45 - 140MM
FORGING TONNAGE 12,000 KN
DRIVE MOTOR RATING 300 KW
CENTER DISTANCE OF DIES 320MM
DIA DIAMETER 1ST STATION 200MM
2ND 3RD 4TH STATION 270MM
MAIN RAM STROKE 320MM
DIE EJECTOR STROKE 130MM
PUNCH EJECTOR STROKE 50MM
WEIGHT OF MACHINE WITH MOTOR 370,000 LBS
COMPLETE WITH NEW 5000 KW INDUCTION HEATER . BAR RACK
SIEMENS S7 MOTOR DRIVE ALL NEW ELECTRICS
13
ID
MA36226
Make
Hatebur
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
Number of forming dies.3
Production. 85 -140ppm VARIABLE SPEED
Forging Tonnage . (2300kN) 230t
Specifications: Metric Standard
Max. outer diameter for round parts. .64mm. 2.519
Max. outer diameter for combination blanks. 55mm. 2.165
Max. width across flats (hex). 56mm. 2.204
initial weight of forging 50-700g
Min. bar diameter. 19mm. 0.748
Max. bar diameter. 40mm. 1.574
Min cutoff Length. 20mm. 0.750
Max cutoff Length. 72mm. 2.834
Drive motor rating. 55kw. 72HP
Center distance of dies. 160mm. 6.299
Die diameters:
1st and 3rd stations. 125mm. 4.921
2nd Station. 150mm. 5.905
Main ram stroke. 160mm. 6.299
Ejector Stroke. 70mm. 2.755
main drive. 53KW. 70HP
Dimensions and weights (Including motor, with heater & conveyor):
Length. 5000mm. 196.8
Width. 3700mm. 145.6
Height. 2000mm. 78.7
Weight (w/Motor). 35,800.0kgs. 78,760.0lbs
Equipped with:
- Variable Speed Drive
- Bar feeding system
- Product conveyor
- Centralized controls
- Split second safety stop
- Overarm-type main slide
- One piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized pressure lubrication system
- 1250 kw Induction Heating Unit
Condition VERY GOOD COMPLETLY REBUILT
14
ID
MA36225
Make
Hatebur
Model
AMP20
YOM
Condition
Good Condition
Photo
See Photo
Number of forming dies. 3
Production. 130-190ppm
Max. outer diameter for round parts. 35mm
Max. width across flats (hex). 33.3mm
Bar diameter. 14-28mm
Cutoff Length. 15-40mm
Forging Tonnage . 900kN
Drive motor rating. 22kw
Center distance of dies. 110mm
Die diameters:
1st and 3rd stations. 80mm
2nd Station. 100mm
Main ram stroke. 110mm
Ejector Stroke. 55mm
Dimensions and weights:
Length. 3200mm
Width. 2600mm
Height. 1550mm
Weight (w/Motor). 11.0 t
Electrics:
Main drive. 22KW
Power supply. 380 volt 3 phase 6 cycles
Equipped with:
- Variable Speed Drive
- Split second safety stop
- Overarm-type main slide
- 460 kw induction heater
- Extensive amount of drawings, manuals, etc.
- One-piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized lubrication system
- Automatic Bar Rack & Workers platform
Condition Excellent, fully rebuilt
15
ID
MA36197
Make
Hatebur
Model
AMP50
YOM
1977
Condition
Good working condition
Photo
See Photo
Initial weight of forgings. 0.17 1.7kg
Max. outer diameter. 92mm
Max. outer dia. for combination rings. 82mm
Max width across flats for hex nuts. 80mm
Bar diameter. 28-50mm
Cutoff length. 32 110mm
Forging stations. 4
Output per minute. 60-100ppm
Forging load . 8000kn
Center distance of dies. 240mm
Die diameter:
1st station. 160mm
2nd,3rd,4th station. 200mm
Stroke of main slide. 240mm
Ejector stroke. 90mm
Motor rating. 170kw
Dimensions:
Length: . 7200mm
Height: . 2650mm
Width: . 5220mm
Feed level.1300mm
Weight including motor. 90tons
Features:
Overarm type main slide
Variable speed drive
Induction Heater
Bar Rack
Rigid bedframe
Automatic central pressure lubrication system
Centralized controls
Split second safety stop
16
ID
MA36184
Make
Hatebur
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
Number of Forming Stations -3
Total Press Load - 2300 kN
Continuous output of drive motor - 55kW
Speed of crankshaft stroke speed /Min- quantity/min (continuously adjustable) - 85 to 140 rpm
Net weight machine (incl.motor) approx.33t
Length(incl.drive motor) - 5000mm
Width - 3700mm
Height - 2000mm
Height of feed axis above floor level-1100mm
Pressram stroke -160mm
Max. ejector stroke die side -70mm
Max. feed length (theoretical) - 100mm
Gripper opening mechanism, vertical stroke - 26mm
Max. bar stop adjustment - 20-72mm
Die spacing -160mm
Die diameter-
1st station -125mm
2nd station - 150mm
3rd station-125mm
Max. Punch diameter in punch holder bore :-
1st station -95mm
2nd station - 95mm
3rd station-95mm
Working range :-
Max. bar stock diameter - 40mm
Min. bar stock diameter - 18mm
Max. height of forging -40mm
cut-off length - 20-72mm
Max. diameter of forging -64mm
Max. width across flats (hexagon) -56mm
Max. Material weight (excl. manufacturing losses) - 700g
Min. Material weight (excl. manufacturing losses) 50g
The machine was overhauled in 2013 when there was added a new induction furnace, changed cams etc.
it complete with induction furnace, water cooling system,
power transformer to the set
Inductor coils installed
The machine was fully repaired in 2013 cams changed also clutches. A siemens controled added. Also in 2013 a new furnace was added with thyristors and automation.
17
ID
MI8431
Make
Hatebur
Model
AMP20
YOM
Condition
Good Condition
Photo
See Photo
Number of forming dies. 3
Production. 130-190ppm
Max. outer diameter for round parts. 35mm
Max. width across flats (hex). 33.3mm
Bar diameter. 14-28mm
Cutoff Length. 15-40mm
Forging Tonnage . 900kN
Drive motor rating. 22kw
Center distance of dies. 110mm
Die diameters:
1st and 3rd stations. 80mm
2nd Station. 100mm
Main ram stroke. 110mm
Ejector Stroke. 55mm
Dimensions and weights:
Length. 3200mm
Width. 2600mm
Height. 1550mm
Weight (w/Motor). 11.0 t
Electrics:
Main drive. 22KW
Power supply. 380 volt 3 phase 6 cycles
Hatebur AMP-20
Equipped with:
- Variable Speed Drive
- Split second safety stop
- Overarm-type main slide
- 460 kw induction heater
- Extensive amount of drawings, manuals, etc.
- One-piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized lubrication system
- Automatic Bar Rack & Workers platform
18
ID
MI8430
Make
Hatebur
Model
AMP30
YOM
2005
Condition
Good Condition
Photo
See Photo
Number of forming dies.3
Production. 85 -140ppm VARIABLE SPEED
Forging Tonnage . (2300kN) 230t
Max. outer diameter for round parts. .64mm. 2.519
Max. outer diameter for combination blanks. 55mm. 2.165
Max. width across flats (hex). 56mm. 2.204
initial weight of forging 50-700g
Min. bar diameter. 19mm. 0.748
Max. bar diameter. 40mm. 1.574
Min cutoff Length. 20mm. 0.750
Max cutoff Length. 72mm. 2.834
Drive motor rating. 55kw. 72HP
Center distance of dies. 160mm. 6.299
Die diameters:
1st and 3rd stations. 125mm. 4.921
2nd Station. 150mm. 5.905
Main ram stroke. 160mm. 6.299
Ejector Stroke. 70mm. 2.755
main drive. 53KW. 70HP
Dimensions and weights (Including motor, with heater & conveyor):
Length. 5000mm. 196.8
Width. 3700mm. 145.6
Height. 2000mm. 78.7
Weight (w/Motor). 35,800.0kgs. 78,760.0lbs
Equipped with:
- Variable Speed Drive
- Bar feeding system
- Product conveyor
- Centralized controls
- Split second safety stop
- Overarm-type main slide
- One piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized pressure lubrication system
- 1250 kw Induction Heating Unit
19
ID
MA36097
Make
Hatebur
Model
AMP30
YOM
1968 and retrofitted and repaired in 2013
Condition
Good Condition
Photo
See Photo
|
See Video
Number of Forming Stations -3
Total Press Load - 2300 kN
Continuous output of drive motor - 55kW
Speed of crankshaft stroke speed /Min- quantity/min (continuously adjustable) - 85 to 140 rpm
Net weight machine (incl.motor) approx.33t
Length(incl.drive motor) - 5000mm
Width - 3700mm
Height - 2000mm
Height of feed axis above floor level-1100mm
Pressram stroke -160mm
Max. ejector stroke die side -70mm
Max. feed length (theoretical) - 100mm
Gripper opening mechanism, vertical stroke - 26mm
Max. bar stop adjustment - 20-72mm
Die spacing -160mm
Die diameter-
1st station -125mm
2nd station - 150mm
3rd station-125mm
Max. Punch diameter in punch holder bore :-
1st station -95mm
2nd station - 95mm
3rd station-95mm
Working range :-
Max. bar stock diameter - 40mm
Min. bar stock diameter - 18mm
Max. height of forging -40mm
cut-off length - 20-72mm
Max. diameter of forging -64mm
Max. width across flats (hexagon) -56mm
Max. Material weight (excl. manufacturing losses) - 700g
Min. Material weight (excl. manufacturing losses) 50g
The machine was overhauled in 2013 when there was added a new induction furnace, changed cams etc.
it complete with induction furnace, water cooling system,
power transformer to the set
Inductor coils installed
The machine was fully repaired in 2013 cams changed also clutches. A siemens controled added. Also in 2013 a new furnace was added with thyristors and automation.
20
ID
MI8429
Make
Hatebur
Model
AMP70
YOM
1976
Condition
Good Condition
Photo
See Photo
NUMBER OF FORGING STATIONS 4
PRODUCTION RATE 50-70 PPM
MAX PART WEIGHT 13.4 POUNDS
MAX OUTER DIAMETER 125MM
MAX WIDTH ACROSS FLATS (HEX) 105MM
BAR DIAMETER MIN / MAX 36 60MM
CUTOFF LENGTH /MIN / MAX 45 - 140MM
FORGING TONNAGE 12,000 KN
DRIVE MOTOR RATING 300 KW
CENTER DISTANCE OF DIES 320MM
DIA DIAMETER 1ST STATION 200MM
2ND 3RD 4TH STATION 270MM
MAIN RAM STROKE 320MM
DIE EJECTOR STROKE 130MM
PUNCH EJECTOR STROKE 50MM
WEIGHT OF MACHINE WITH MOTOR 370,000 LBS
COMPLETE WITH NEW 5000 KW INDUCTION HEATER . BAR RACK
SIEMENS S7 MOTOR DRIVE ALL NEW ELECTRICS
21
ID
MA35677
Make
Hatebur
Model
AMP70
YOM
1978
Condition
Good Condition
Photo
See Photo
Press force total : 1200 To
Induction system ( convertor) Elotherm, rebuild on 2015.
This machine worked in the former OPEL factory in Germany until October 2020.Forging
Forming stations : 4 no
Max outer part dia : 145 mm,
Max outer dia combo blanks : 122 mm,
Bar dia range : 36 - 75 mm,
Initial weight : 0.4-5.0 kg,
Cutoff length range: 45 - 135 mm,
Max across the flats: 105 mm,
Die center distance : 320 mm,
Die dia 1st/2nd, 3rd & 4th : 200 / 270 mm,
Stroke rate : 50-80 per min,
Machine weight : 175 tons.
Bar rack for incoming material (with possibility to use bars with the length 3 and 6 meters by hateur specs the maximum diameter of bars is 65 mm, but it was used maximum 50 mm).
Elotherm induction heater with 3,000 kWt capacity.
Water scale and water oil separation system fir induction heater and hot former.
Hatebur hot former AMP 70 with nominal force 1200 metric tons.
System of unloadinf conveyors.
Besides that in the list of sale of included as set of spare parts including the new shear.
22
ID
MA35671
Make
Hatebur
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 35800 kg
motor power 55 kW
23
ID
MA35151
Make
Hatebur
Model
AMP30
YOM
1981
Condition
Good Condition
Photo
See Photo
Weight Of The Pieces: 50-700G
Max Ext Diameter For Round Pieces : 64mm
Max Ext Diameter For Special Products : 55mm
Hexagon Across Flat : 56mm
Bars Diameter : 18-40mm
Lenght Of Shafts : 20-72mm
Motor Power : 55kw
pression : 2300kN(230t)
Tools
No. Station :3
Distance BEtween Dies : 160mm
Dies Diameter 1st and 3rd station : 125mm
2nd station : 150mm
Course
Ram Stroke : 160mm
Connection : 70mm
Electricite
Energy Consumption At Max Production : 100kva
Energy Consumption At Start : 125kva
Cooling Water
Needed Pressure : 4bar
machine will be completely reconditioned mechanically, and with new electrics.
Consumption :(depending on the piece) : 30Nm/h
Pressurized Air
Needed Pressure : 5.5-10bar
Consumption (Aspiration State ) : 3NM3/N
Dimensions of the Machine With Motor
Lenght : 5000mm
Width : 3700mm
Height : 2000mm
Height Above Ground Of Feeding Axis : 1100mm
Weight (Motor Included ) : 35.8TON
A complete rebuilding, with new electrics,
With external clutch brake unit and oversized transfer sleeves
24
ID
MA34889
Make
Hatebur
Model
AMP70
YOM
1978
Condition
Good Condition
Photo
See Photo
Part Dia:120 mm
Max Cutoff Length:135 mm
Max Die Ejector:130 mm
Part Wt:3 kgs
Max Initial Part Weight:3 kgs
Min Cutoff Length :45 mm
Max Outer Dia for Combination Parts :110 mm
Max Width Across the Flats Hex:105 mm
Max Strokes per Minute:70
Die Centers:320 mm
Die Diameter 1st:200 mm
Die Diameter 2nd:270 mm
Die Diameter 3rd:270 mm
Die Diameter 4th:270 mm
Ram Stroke:320 mm
Punch Ejector Stroke:50 mm
Main Motor Power :300 kW
Machine Length:9,200 mm
Machine Width:6,200 mm
Machine Height:3,100 mm
Machine Weight:176,000 kgs
Power Rating of Induction Heater:3,000 kW
Press force total: approx. 1300to
All parts are complete
The press is in a good and usable condition
Converter rebuild 2015
Cooling tower of Hatebur 1
Manufacturer: Gohl
Year of manufacturing: 2007
The cooling tower was in use up to October 2020
It was maintained/repaired/upgraded only by Hatebur
25
ID
MA34884
Make
Hatebur
Model
AMP30
YOM
1966
Condition
Good Condition
Photo
See Photo
This machine worked in Japan until 2008, then it has been purchased by a Swiss dealer; in 2012 we bought it together with its sister-machine, that has been completely overhauled and started in 2014.
Max production rate/min:pcs 140
Pressing power: 230 ton
Stroke:160 mm
Max ejector stroke: 70 mm
Max rod diameter: mm 40
Min rod diameter: mm 19
Max cut-off length: mm 60
Min cut-off length: mm 20
Max outside diameter for round parts: mm 64
Driving power: Kw 55
Total weight: ton 36
Number of forging station : 3
26
ID
MA34605
Make
Hatebur
Model
AMP30
YOM
1968
Condition
Good Condition
Photo
See Photo
|
See Video
diameter range :64 mm
max. width across flats :56 mm
max. outside dia. of round pieces : 64 mm
bar him. : 18-40 mm
cutting length : 20-72 mm
output - pieces/min : 140
number of forming stations : 3
press power : 230 t
weight : 35800 kg
motor power : 55 kW
the induction system is 5 years old
It is a complete production line
27
ID
MA34581
Make
Hatebur
Model
AMP30
YOM
1974
Condition
Good Condition
Photo
See Photo
diameter range :64 mm
max. width across flats :56 mm
max. outside dia. of round pieces : 64 mm
bar him. : 18-40 mm
cutting length : 20-72 mm
output - pieces/min : 140
number of forming stations : 3
press power : 230 t
weight : 35800 kg
motor power : 55 kW
28
ID
MA34580
Make
Hatebur
Model
AMP30
YOM
1966
Condition
Good Condition
Photo
See Photo
diameter range : 64 mm
max. width across flats : 56 mm
max. outside dia. of round pieces : 64 mm
bar him : 18-40 mm
cutting length : 20-72 mm
output - pieces/min : 140
number of forming stations : 3
press power : 230 t
weight : 35800 kg
motor power : 55 kW
29
ID
MA33760
Make
Sakamura
Model
HBP100
YOM
This is a 1982 machine which was completely overhauled in 2005
Condition
Good Condition
Photo
See Photo
|
See Video
4 Die,
Forge tonnage rating:230 tons
Max part OD:64 mm
Min-Max blank height:12 - 30 mm
Bar Diameter:25 - 40 mm
Cutting length:20 - 70 mm
Forming Stations:4
Production rate:Up to 90 per minute
Die inter-center crank pin dia:240 mm
Crank pin diameter:360 mm
Ram stroke:80 mm
Ram Stroke:240 mm
Ejector stroke:40 mm
PKO:20 mm
Main motor power:75 Kw
Machine weight:60 tons,
Inspection Under power is possible
30
ID
MA33250
Make
Hatebur
Model
AMP70
YOM
1970
Condition
Good Condition
Photo
See Photo
NUMBER OF FORGING STATIONS:
PRODUCTION RATE: 50-70 PPM
MAX PART WEIGHT: 13.4 POUNDS
MAX OUTER DIAMETER: 125 MM
MAX WIDTH ACROSS FLATS (HEX): 105 MM
BAR DIAMETER MIN / MAX : 36 60 MM
CUTOFF LENGTH /MIN / MAX: 45 - 140 MM
FORGING TONNAGE: 12,000 KN
DRIVE MOTOR RATING: m300 KW
CENTER DISTANCE OF DIES: 320 MM
DIA DIAMETER 1ST STATION: 200 MM
2ND 3RD 4TH STATION: 270 MM
MAIN RAM STROKE : 320 MM
DIE EJECTOR STROKE: 130 MM
PUNCH EJECTOR STROKE: 50 MM
WEIGHT OF MACHINE WITH MOTOR: 370,000 LBS
COMPLETE WITH BAR RACK .BAR LENGTHS 30 FEET
NEWELCO INDUCTION HEATING SYSTEM WITH
NOMINAL OUTPUT POWER: 900 KW (X5)
NOMINAL FREQUENCY: 1 KHZ
NOMINAL INPUT VOLTAGE: 840 VAC
MAXIMUM OUTPUT VOLTAGE:1200 VAC (V X 15 =80 )
MAXIMUM RECTIFIER VOLTAGE: 1000 VAC
MAXIMUM DC CURRENT: 2 X 470 = 940 AMPS ( 2 RECTIFIER )
SHUNT RATIO: 60Mv / 600 amps
MAXIMUM DC CURRENT: 47.0 Mv
START CURRENT 8%: 3.8 Mv
FREQUENCY RANGE: 700 HZ 1100 HZ
OSCILLATOR RANGE: 2800 HZ 4400 HZ
T.O.T FACTOR: 834
31
ID
MA32724
Make
Hatebur
Model
AMP70
YOM
Condition
Good Condition
Photo
See Photo
Working range
Initial weight of forgings : 0.4-5.0 kg 90-11lb
Max. outer diameter (round parts) : 145mm 5.71in
Max. outer diameter for combination blanks : 122mm 4.8 in
Max. width across flats (hex) : 130mm 5.12 in
Bar diameter : 36-75mm 1.40-3.0 in
Cut of length : 45-150mm 1.77-5.91 in
Performance data
Production (Speed infinitely variable ) : 50-80 parts/min
Forging tonnage : 15000kN
Drive motor rating : 350 kW
Tooling
Forging stations : 4
Center distance of dies : 320mm 12.60 in
Die diameter : 1st station : 200mm 7.87 in
2 nd and 3rd station : 290mm 11.42 in
4th station : 270mm 10.63
Strokes
Main ram stroke : 320 mm 12.60 in
Die ejector stroke : 130/150mm 5.12/5.91 in (optional)
punch ejector stroke : 50 mm 1.97 in
Utility requirements
Electrical
Power requirement, production : 550kVA
Power requirement, start : 660kVA
Cooling water :
Min. pressure : 6 bar 85 psi
Max. consumption (depending on forging) : 120m3/h 31700US gal/h
Compressed air :
Min. pressure : 5.5-10 bar 78-142 psi
Consumption (in uncompressed state) : 4m3/h 140cu.ft/h
Dimensions and weight :
Machine dimensions with standard covers (noise abatement cabin on request)
length : 9200 mm 362 in
width : 6200 mm 244 in
Height without/with hoist : 3100/4650 mm 122/183 in
Pass line height above floor : 1500 mm 59 in
Weight of machine with motor : 172 t 380,000ib
32
ID
MA32645
Make
Hatebur
Model
AMP70
YOM
1965
Condition
Good Condition
Photo
See Photo
Press capacity: 1200 ToF
Max across the flats: 105 mm,
Weight of piece: 0.445-3.0 kg,
Min bar diameter: 40 mm,
Cutting stroke: 260 mm,
Die center distance: 320 mm,
Max diameter of die: Forming section 1-200 mm,
Forming section 2,3,4-270 mm,
Max die ejector stroke: 1300 mm (die/50 mm (ram)
Area of the press: 9200 x 5900 mm,
Power of induction heating installation: 3000 KW,
Power of auxiliary motors: 7 KW,
Productivity: 1650-4500 pcs/h/7-12 to/h
Forming section:4
Max outer diameter of part: 120 mm,
Max width:80 mm,
Max bar diameter: 65 mm,
Stroke of ram: 320 mm,
Length for cutting: 45-135 mm,
Stroke: 35-70/min
Height of the press: 3100 mm,
Main motor power: 300 KW
Weight: 176 to
Over the years several interventions have been made to it at regular scheduled repairs to keep them within normal operating parameters. The most important intervention on the machine was made in 2002. In this procedure the AMP70 machine was completely renovated besides replacing used mechanical components it was made the complete replacement of the induction heating installation with a new AEG-Eloterm germany installation also the lubrication system was updated with Weorner components. In 2011 was made an overhaul of the mechanical system of machine. In overhaul were rebuilding the slides, brass bushings cam shafts and the ram of machine.
In the URB bearings plant from Brasov with AMP70 it used to be made bearing rings from bar steel 100 Cr6 (max diameter of bar 65 mm), with the ma. weight of 3.0 kg for this machine we have tools for 58 types of bearings as follows:
From 1210 to 1213 From 6408 to 6410
From 2210 to 2212 From 6308 to 6314
From 2308 to 2310 From 30210 to 30218
From 6211 to 6217 From 32210 to 32218
Moreover we also hold completer technical documentation for all type of bearings rings mentioned above and drawings for main component parts of the machine.
The machine is equipped with distilled water cooling system and its electrical transformer to provide electrical power required for inducton heating system.
Electric transformer
Type: T.T.U. AL
Manufacturer: Electroputere
Rated capacity: 5000 KVA
High voltage: 6000 v
Low voltage: 5700 V
Output- voltage: 680 V
Frequency: 50 Hz
phase: 6
Connection method: Yyn0/Dyn11
The press has the following spare parts:
Electric engine: 1 piece feed roller clutch gear: 1 piece
Adjustment wedges: 3 pieces Transmission belt wheel: 1 piece
Brake hub: 1 pieces Plated clutch discs: 3 pieces
Clutch hub: 1 pieces Not plated clutch discs: 3 pieces
head finger grip: 1 pieces Expulsion upper arm: 1 pieces
Fuses ram port punch: 20 pieces Cutting fuses: 6 pieces
33
ID
MA32632
Make
Nedschroef
Model
MW48
YOM
Condition
Good Condition
Photo
See Photo
3 die
38 mm Maximum Bar Diameter
15-60 mm Min/Max Bar Length
50 mm Die KO
53 mm Maximum Product Diameter
1050 Kn Forge Load
150 Pieces per Minute
Equipped with: Induction Heat and 6 meter Bar Feed
34
ID
MA32631
Make
Hatebur
Model
AMP30
YOM
1970
Condition
Good Condition
Photo
See Photo
19-40 mm Bar Diameter
20-72 mm Cutoff Length
64 mm OD Round Part
56 mm Across Flats
85-140 Pieces per Minute
2300 Kn Forge Tonnage
Equipped with: Bar Feed (7m long)
Weight 32,000 Kg
1. Block has been machined once and has been bushed back.
2. The vendor has the manuals and drawings.
3. The machine has been out if service for 3 years and has been in storage.
4. All those items included. Die block was replaced 4 years ago. All available machine spares associated with the machine are sold as part of the machine but there are no lists available An estimate of the replacement cost of these spares is approximately $A200,000
5. No lists available.
6. The machine has been out of service for 3 years.
7. The machine is 110volt and it has a transformer to convert it to Australian 240 volt
35
ID
MA32563
Make
Sakamura
Model
HF-1000-4
YOM
2013 installed in 2015
Condition
Good Condition
Photo
See Photo
Working range:
Initial weight:2440 kg,
Max. outer diameter of round parts:48-15 mm,
Max hex with across flats: mm
Max square with across flats:mm
Max diameter for single ring:mm,
Max. diameter for combination ring:mm,
Max diameter for combination ring:48-105 mm,
Max. spider width across flats: mm,
Bar diameter:32-60 mm,
Cut of length:25-110 mm,
Performance:
Strokes per minute: 45-100 1/min,
Max. drive motor rating:205 kW
Tooling
Number of forging station:4
Tool forging load:10,000 kN,
1000 ton
Center distance of dies:250 mm,
Depth of die bloc bore: #1 =350, #2=349
#3 = 348, #4 = 347
Die diameter: 1st: 215 mm,
2nd: 215 mm,
3rd : 215 mm,
4th: 200 mm,
Punch holder diameter: 1st: 125 mm,
2nd: 135 mm,
3rd : 135 mm,
4th: 95 mm,
Stroke:
Press ram: 300 mm,
Shearing slide: 124 mm,
Die ejector: 80 mm,
Punch ejector: 40+10 mm,
Bar stop adjustment: 50 mm,
Induction heater:
Maker: SMS
Max. drive motor rating: 2400 mm,
36
ID
MA32045
Make
Hatebur
Model
AMP50
YOM
Condition
Good working condition
Photo
See Photo
Total Tonnage 800 metric tons . Forming Stations : 1st station : 200 metric tons , 2nd station 400 metric tons , 3rd station 400 metric tons , 4th station 400 metric tons , Eccentricity of resultant combined forging tonnage 120 mm
37
ID
MA31893
Make
Tyazhpressmash
Model
TPM30
YOM
Condition
Brand New
Photo
See Photo
CONTENTS
Designation and Field of application
General view of Hot Former
Technical specifications and design
Delivery set
Other terms and conditions
Supervision/mounting and set-up/commissioning
Commercial terms
1. Designation and Field of Application
The 2500 kN Hot Former is designed for production of parts from carbon steel and alloy steel as well as for simultaneous production of inner- and outer bearing rings by means of hot die forming operation from initial round hot rolled steel bars.
Hot Former is intended to be employed in metal-working industry in batch- and mass production. Hot Former is designed to be incorporated into Hot Forming Production Lines.
As initial material hot-rolled high precision steel rods are used.
2. General view of Hot Former
For Picture of the Hot Former refer to Picture 1.
3. Technical specifications and design of 2500kN Hot Former
3.1 Main components of Hot Former:
- Machine frame is a closed heavy frame of high rigidity. It is made of a one-piece steel casting which is subjected to stress relief heat treatment. The frame deformation under load is insignificant.
- Upsetting slide is a steel casting with arc-like lug, provided with two pairs of guideways arranged on both sides of crankshaft;
- Die block is made of high-tensile steel and is subjected to heat treatment. It is equipped with removable covers which are designed to facilitate the die set changing.
- Hot Former drive ensures smooth adjustment of the upsetting slide spm.
- Drive shaft with clutch and brake clutch and brake are provided with electrical/pneumatic control. Valves are arranged directly at the clutch and brake and actuate without any noticeable delay.
- Crankshaft w/o webs is of high rigidity. It is made of advanced alloy steel and is US tested for cracks presence;
- Distribution shafts (transverse, longitudinal, etc.) rotate in slider bearings and serve for setting the operation cycle and amount of movement of all Hot Former mechanisms via cams arranged on these shafts.
- Die kick-outs are driven via the lever from the cam provided on the machine crankshaft. Provided at the top of the lever are three pressure bolts which impart movement to the kick-out rods. Kick-out lever is protected from overload by means of a safety device.
- The cut-off mechanism is designed to cut a slug off a heated bar stock and transfer it to the first forming station. Cut-off system is of open type and it consists of a stationary and a moveable blades with semicircular cutting edges.
- The bar clamping mechanism serves to firmly press bar to the stationary blade while cutting to provide for a high-quality cut. Bars are clamped via rod which moves through the insert and sets of disc springs.
- Slug clamping mechanism is intended to clamp a slug to the blade while cutting and to hold it so clamped while transferring it to the 1-st station.
- The punch sensing/cooling mechanism serves to check whether there is a slug caught on the punches and also to cool the tool. In case a slug got stuck on the punch the Hot Former stops its operation. Punch sensors can be easily changed. This mechanism is provided with a tilting bracket which serves to facilitate tool changing.
- Transfer mechanism is designed to clamp a workpiece discharged from dies and transfer it from one station to another one. Then it gets unclamped and returns to the initial station to perform the next cycle.
- Longitudinal transfer mechanism is driven via cams arranged on the camshaft.
- Transfer opening mechanism is driven via cams. Cams can be cycle adjusted.
- Material feed mechanism is driven from the cam via the slotted-link leverage. Unidirectional intermittent rotation of feed rollers is performed by means of the overrunning clutch. A permanent acting brake is provided to perform braking at the leverage return stroke.
- The material feed is performed by two quick-change roller couples. Feed rollers are clamped and unclamped by means of pneumatic cylinders. Clamping force of feed rollers can be adjusted based according to bar diameter.
- Material feed stop is adjustable, can be adjusted by the operator from the control panel.
- Short bar ends discharge system short bar ends are discharged by the operator while setting-up right after cut-off by means of pressing a button on the control panel; further during regular working cycle the machine itself selects the proper time to discharge short ends by means of automatic discharge system.
- Oil circulation lubrication system, 2-circuit lubrication system with the lubrication plant from the machine Manufacturer. Interlocking of the Hot Former operation is provided in case of a delay in any one of the controlled feeders operation. Provided in the lubrication plant is a fine filter with electric signalling device which serves to warn about clogging.
- Tool cooling system. Water is supplied to the exterior/interior surfaces of punches and dies by means of tubes and sprayers. Water is drained into the workshop drain line.
For Technical Specifications of Hot Former refer to table 3.1
Table 3.1 Technical specifications of Hot Former
Slug length for one forged part, mm
minimum : 20
maximum : 72
Rated force: 2500 kN
Slide stroke : 160 mm
Max. forged part OD: 67* mm
Max. forged part height: 40* mm
Slide spm, min-1: 10 120
Die kick-out stroke: 70 mm
Punch kick-out stroke: 26*1 mm
Number of stations: 3
Distance between forming stations: 160 mm
Distance between cut-off station and the 1st forming station: 160 mm
Slug weight: 0,05 0,7 kg
Total power of electric motors: 72,02* kW
Main drive electric motor power: 71* kW
Compressed air pressure: 0,4+0,1** MPa
Cooling water pressure:0,6** MPа
Hot Former overall dimensions, mm
length : 5330*
width: 3230*
Height above floor level: 2980* mm
* to be confirmed at the designing stage
** to be provided by the Customer
*1 Basic version of Hot Former w/o punch kick-out mechanism.
4. Delivery Set
4.1 For the Delivery Set refer to Table 3.2 below
Table 4.1
Ref. No. Designation Description Q-ty Notes
1 Hot Former
(complete designation is assigned at the stage of Contract finalizing)
Included into the machine Delivery Set:
-set of accessories;
- set of spare parts.
2500 kN Hot Former
1 Delivery Set according to the Machine specifications
2
Documentation: -Service Manual; 1 In Russian and in English
Service Manuals for outsourced components in the language of Supplier
-Foundation (construction request) In Russian and in English
- Assembly drawings of Hot Former and its main assembly units;
- Drawings of rapid wearing parts;
-Electric equipment diagram;
-Lubrication diagram;
-Pneumatic diagram 1 In Russian and in English
4.2 ОАО Tyazhpressmash herewith offers to manufacture tools and to develop manufacturing technique to produce the Customers parts on the basis of a separate contract.
4.3 Not included into the Delivery Set:
- leveling and shock-absorbing elements;
- civil works of foundation building and manufacture of embedded parts ( respective drawings are supplied);
- induction heater (to be outsourced by the Customer);
- sound enclosure complete with servicing platform (can be supplied on the basis of a separate contract);
- water-oil separator (can be supplied on the basis of a separate contract);
- automatic rack intended to store and feed the bar stock into the induction heater (can be supplied on the basis of a separate contract);
- discharge conveyor to remove parts and wastes from the working zone (can be supplied on the basis of a separate contract);
- cooling conveyor (can be supplied on the basis of a separate contract);
- mounting supervision and set-up/commissioning;
- lay-out of supply mains up to the cabinets and distribution boxes;
- initial filling with working fluids.
5 . Other requirements
5.1 Equipment shall be painted in the manufacturers standard color RAL6034 (pastel turquoise) unless specified otherwise.
5.2 The equipment is intended for supply to macroclimatic regions with temperate climate. It shall operate indoors in heated rooms with air temperature ranging from +5°С up to +40°С at altitude above sea level up to 1000 m.
6. Mounting supervision and set-up/commissioning (on the basis of a separate contract)
6.1 Mounting supervision shall be performed by the Customers personnel and with the assistance of OAO Tyahpressmash technicians.
6.2 Set-up/commissioning shall be performed by OAO Tyazhpressmash technicians with the participation of the Customers personnel.
6.3 Set-up means setting-up the devices and mechanisms incorporated into the machine and the control system; it also means setting the components proper interaction to ensure rated technical specifications.
6.4 Presumable work schedule:
- 2 technicians from ОАО Tyazhpressmash visit the Customer for 5 days for foundation civil works acceptance;
- 4 technicians from ОАО Tyazhpressmash visit the Customer for 45 days to render mounting supervision services;
- 6 technicians from ОАО Tyazhpressmash visit the Customer for 30 days to render set-up services.
6.5 During set-up/commissioning services the technician from AO Tyazhpressmash provide training for the Customers personnel to operate the equipment supplied.
Delivery time: 6-8 months
38
ID
MA31852
Make
Hatebur
Model
AMP20
YOM
1972
Condition
Good Condition
Photo
See Photo
Round parts; depending on filling degree, sequence of operation as well as steel grade and forging temperature
- Max. outer diameter:
Round parts of steel approx. 35 mm
Round parts of brass approx. 38 mm
Max. with across flats (hex) approx. 32 mm
Bar diameter 14,25 mm
Cutoff length 16-40 mm
Initial weight 20 g-150 g
Technical data
Strokes per minute: 90-150/min
complete with Induction Heater & bar rack
Total tonnage: 800 kN
Center distance of dies: 110 mm
Die diameter 1st and 3rd station: 80 mm
Die diameter 2nd station: 100 mm
Punch diameter all station: 75 mm
Ejector stroke: 55 mm
Stroke of main slide: 110 mm
Drive motor rating: 24.5 kW
Machine weight with drive motor: 9.6 ,metric tons
Complete with Sound Enclosure
Dimension
Length 32000 mm x Width 2600 mm x Height 1420 mm
Feed line above floor 800 mm
39
ID
MA31845
Make
Hatebur
Model
AMP30
YOM
1972
Condition
Excellent condition,under power
Photo
See Photo
|
See Video
Number of Stations : 3
Parts weight : 50 - 700 g
Cutoff length : 20 - 70 mm
Max width (A/F -HEX) : 55 mm
Max Dia round parts : 60 mm
Combi blanks : 55 mm
Bar diameter min. : 18 mm
Bar diameter max : 40 mm
Strokes per minute : 85-140 (Variable speed)
Forming load : 250 Tons
Main motor rating : 55 KW
40
ID
MA31513
Make
Hatebur
Model
AMP30
YOM
Condition
Good Condition
Photo
See Photo
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 23 T
motor power 55 kW
measurements 410x243x204
41
ID
MA31434
Make
Hatebur
Model
AMP30
YOM
Rebuilt and Upgraded in 2003
Condition
Good Condition
Photo
See Photo
Major specifications metric standard
Max. outer diameter 64.0 mm 2.519"
Max. outer diameter for combination rings 55.0 mm 2.165"
Max. width across flats for hex nuts 56.0 mm 2.204"
Minimum raw material diameter 19.0 mm 0.748"
Maximum raw material diameter 40.0 mm 1.574"
Minimum cutoff length 19.0 mm 0.748"
Maximum cutoff length 72.0 mm 2.834"
Center distance of dies 160.0 mm 6.299"
Max Bar Length 10.0 mtrs 32.8 ft
Die diameters:
1st and 3rd stations 125.0 mm 4.921"
2nd station 150.0 mm 5.905"
Stroke of main slide 160.0 mm 6.299"
Ejector stroke 70.0 mm 2.755"
Main motor 53.0 kw 71.0 hp
Net weight 35,800.0 kgs 78,760.0 lbs
Floor space (including motor, without heater and conveyor):
Length 5,000.0 mm 196.8"
Width 3,700.0 mm 145.6"
Height 2,000.0 mm 78.7"
Complete with:
Overarm-type main slide
Variable speed drive
Rigid bedframe
Accurate cut-off
One-piece tool block assures accurate parts and long tool life
Automatic central pressure lubrication
Centralized controls
Split-second safety stop
1,000 kW Inductotherm Induction Heater new 2002
Bar Feeding System new 2002
Complete Electrics
42
ID
MA31431
Make
Hatebur
Model
AMP30
YOM
1971/14
Condition
Good Condition
Photo
See Photo
diameter range 64 mm
max. width across flats 56 mm
max. outside dia. of round pieces 64 mm
bar dia. 18-40 mm
cutting length 20-72 mm
output - pieces/min 140
number of forming stations 3
press power 230 t
weight 23 T
motor power 55 kW
measurements 410x243x204
43
ID
MA31429
Make
Hatebur
Model
AMP30
YOM
1970
Condition
Good Condition
Photo
See Photo
Number of forming dies 3
Production 70-120ppm
Forging Tonnage (2300kN) 230t
Built 1970's
Specifications: Metric Standard
Max. outer diameter for round parts 64mm 2.519
Max. outer diameter for combination blanks 55mm 2.165
Max. width across flats (hex) 56mm 2.204
Min. bar diameter 19mm 0.748
Max. bar diameter 40mm 1.574
Min cutoff Length 20mm 0.750
Max cutoff Length 72mm 2.834
Drive motor rating 55kw 72HP
Center distance of dies 160mm 6.299
Die diameters:
1st and 3rd stations 125mm 4.921
2nd Station 150mm 5.905
Main ram stroke 160mm 6.299
Ejector Stroke 70mm 2.755
main drive 53KW 70HP
Dimensions and weights (Including motor, with heater & conveyor):
Length 5000mm 196.8
Width 3700mm 145.6
Height 2000mm 78.7
Weight (w/Motor) 35,800.0kgs 78,760.0lbs
Equipped with:
- Variable Speed Drive
- Bar feeding system
- Product conveyor
- Centralized controls
- Split second safety stop
- Overarm-type main slide
- One piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized pressure lubrication system
- Induction Heating Unit
44
ID
MA31393
Make
Hatebur
Model
AMP30
YOM
1971
Condition
Good Condition
Photo
See Photo
Number of forming dies..3
Production.... 70-120ppm
Forging Tonnage ... (2300kN) 230t
Built..... 1970's
Specifications: Metric Standard
Max. outer diameter for round parts..64mm. 2.519
Max. outer diameter for combination blanks.55mm. 2.165
Max. width across flats (hex)... 56mm.. 2.204
Min. bar diameter..... 19mm. 0.748
Max. bar diameter.....40mm. 1.574
Min cutoff Length..... 20mm.. 0.750
Max cutoff Length..... 72mm.. 2.834
Drive motor rating..... 55kw.. 72HP
Center distance of dies.... 160mm. 6.299
Die diameters:
1st and 3rd stations.... 125mm. 4.921
2nd Station..... 150mm. 5.905
Main ram stroke.....160mm. 6.299
Ejector Stroke..... 70mm.. 2.755
main drive...... 53KW. 70HP
Dimensions and weights (Including motor, with heater & conveyor):
Length... 5000mm. 196.8
Width... 3700mm. 145.6
Height... 2000mm. 78.7
Weight (w/Motor).. 35,800.0kgs. 78,760.0lbs
Equipped with:
- Variable Speed Drive
- Bar feeding system
- Product conveyor
- Centralized controls
- Split second safety stop
- Overarm-type main slide
- One piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized pressure lubrication system
- Induction Heating Unit
45
ID
MA30873
Make
Hatebur
Model
AMP70
YOM
1965
Condition
Good Condition
Photo
See Photo
Machine type Hot former
Make: HATEBUR
Serial number 1404 Forming sections 4
Press capacity 1200 ToF Max outer diameter of part 120 mm
Max across the flats 105 mm Max width 80 mm
Weight of piece 0.445-3.0 kg Max bar diameter 65 mm
Min bar diameter 40 mm Stroke of ram 320 mm
Cutting stroke 260 mm Length for cutting 45-135 mm
Die center distance 320 mm
Max diameter of die Forming section 1 200 mm
Forming section 2, 3, 4 270 mm
Max die ejector stroke 130 mm (die) / 50 mm (ram) Stroke 35-70/min
Area of the press 9200 x 5900 mm Height of the press 3100 mm
Power of induction heating installation 3.000 KW Main motor power 300 KW
Power of auxiliary motors 7 KW
Productivity 1650 4500 pcs/h / 7-12 To/h Weight 176 To
Electric transformer
Type T.T.U. Al
Manufacturer ELECTROPUTERE
Rated capacity 5000 KVA
High voltage 6000 V
Low voltage 5700 V
Output voltage 680 V
Frequency 50 Hz
Phase 6
Connection method Yyn0/Dyn11
The press has the following spare parts:
Electric engine 1 piece Feed roller clutch gear 1 piece
Adjustment wedges 3 pieces Transmission belt wheel 1 piece
Brake hub 1 piece Plated clutch discs 3 pieces
Clutch hub 1 piece Not plated clutch discs 3 pieces
Head finger grip 1 piece Expulsion upper arm 1 piece
Fuses ram port punch 20 pieces Cutting fuses 6 pieces
46
ID
MA30642
Make
Hatebur
Model
AMP30
YOM
1987
Condition
Very good condition
Photo
See Photo
Number of forming dies..3
Production.... 70-120ppm
Forging Tonnage ... (2300kN) 230t
Built..... 1987
Specifications: Metric Standard
Max. outer diameter for round parts..64mm. 2.519
Max. outer diameter for combination blanks.55mm. 2.165
Max. width across flats (hex)... 56mm. 2.204
Min. bar diameter..... 19mm. 0.748
Max. bar diameter.....40mm.. 1.574
Min cutoff Length..... 20mm. 0.750
Max cutoff Length..... 72mm. 2.834
Drive motor rating..... 55kw.. 72HP
Center distance of dies.... 160mm. 6.299
Die diameters:
1st and 3rd stations.... 125mm. 4.921
2nd Station..... 150mm. 5.905
Main ram stroke.....160mm. 6.299
Ejector Stroke..... 70mm. 2.755
main drive...... 53KW. 70HP
Dimensions and weights (Including motor, with heater & conveyor):
Length... 5000mm. 196.8
Width... 3700mm. 145.6
Height... 2000mm. 78.7
Weight (w/Motor).. 35,800.0kgs. 78,760.0lbs
Equipped with:
- Variable Speed Drive
- Bar feeding system
- Product conveyor
- Centralized controls
- Split second safety stop
- Overarm-type main slide
- One piece steel casting bedframe
- Electro-pneumatically operated clutch and brake
- Automatic centralized pressure lubrication system
- Newelco Induction Heating Unit
- Hatebur spare parts and tooling
47
ID
MA30485
Make
Hatebur
Model
AMP30-S
YOM
1971
Condition
Photo
See Photo
Specification attached
48
ID
MA30202
Make
Sakamura
Model
HNP80
YOM
1992-Rebuilt 2007
Condition
Good Condition
Photo
See Photo
Forging Capacity: 1600 Kn
1 Cut-off Die (bush type system)
85-160 PPM depending on part
19-35mm x 60L Bar Resp. Wire Diameter
280 g maximum Cut-off Slug Weight
20-53mm Blank Outer Diameter
8-35mm Blank Height
Die Diameter:
-Performing - 58mm
-1st Station - 155mm
-2nd Station - 130mm
Punch Diameter:
-Performing - 40mm
-1st Station - 90mm
-2nd Station - 50mm
6mm Punch Adjustment for the Performing Ram
Equipped with:magazine bar rack,ajax induction heater
Machine Dimensions - L x W X H: 4.700x2.700x1.800mm (only HNP-80)
Motor Capacity - 37 Kw
Machine Weight - about 30 tons (only HNP-80)
49
ID
MA29425
Make
Peltzer & Ehlers
Model
VLP450
YOM
Condition
Good Condition
Photo
See Photo
Capacity: 450 ton,
Stroke: 400 mm,
Stroke rate: 40 min^-1
Die clearance: 245 mm,
Die diameter: 220 mm,
Die stations: 4,
Ejector: 3
Ejector (stroke): ~120 mm,
Stroke position adjustable: ~200 mm,
Required air quantity: 100 I/min,
Drive capacity: 45 kW,
Dimensions: 2600 x 2900 x 5750 mm ( W x D x H),
Total weight: 50 ton,
Mode of operation: mechnaical
50
ID
MA29424
Make
National Kayser
Model
M16
YOM
Condition
Good Condition
Photo
See Photo
Capacity: 200 ton,
Stroke: station 1,2,3,4- 29,28,6 22,2; 22,2 mm,
Strokes: 80 min^-1,
Driving power: 22 kW,
Dimensions: 2130 x 5610 mm (W x D x H),
Total weight: 23,5 ton,
Cutting cap: 22 mm,
Cutting length min/max: 0,5-19 mm,
Number of dies: 5,
51
ID
MA28898
Make
Sakamura
Model
HNP40
YOM
1998
Condition
Excellent condition,under power
Photo
See Photo
Stations : 3,
Cut of Diameter x length : 13 x 25 mm,
Stroke : 20 mm,
Forging Load : 300 Kn,
Output (Minimum) : 200.
In addition to the cutting stage, this former is equipped with a three-station forging process (open upset, forming, piercing).
After cutting in the first stage, employing the independent twin ram, the upset is transferred to the second process by the up thrust pusher.
A wide selection of simple products such as hex nuts, bearing donut blanks, flange nuts, square nuts, lock nuts, and washers can be produced
