Menu
Home
Sell Machines
Hot Deals
Main Site
VKengg.co.in
Category : Gear Machines
Sub-Category : Gear Generator Spiral Bevel & Hypoid
Total Machines Found :
78
Select
| Machine Details
1
ID
MA35832
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Cone Distance Maximum:9"
work Head Angle:-12 deg to 90 deg
Extreme Ratio:any practical ratio
Min Ratio for Pinions operate w/Formate cutters 2 to 1
Max Gear Pitch Diameter: (30 deg spiral angle)
10 to 1 ratio : 18"
2 to 1 ratio:16"
1 to 1 ratio: 12.75"
Face Width Maximum:2.75"
number of Teeth: 5-150
Diametral Pitch coarsest:2 / 12.7 Mod.
work spindle
Diameter of taper large end :3 29/32"
taper per foot:39/64"
depth of taper:6"
Diameter of hole through spindle:3 1/16"
Diameter of Spindle Nose:5 1/2"
cutter diameters:6", 7.5", 9" & 12"
Work Head Settings
Max offset above center:4.5"
Max offset below center:4.5"
Max dist mach center to spindle nose:13.5"
Min dist mach center to spindle nose:2.5"
machine floor space:75" x 114"
machine weight:23,000 lbs
2
ID
MA35691
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Cone Distance Maximum:9"
work Head Angle:-12 deg to 90 deg
Extreme Ratio:any practical ratio
Min Ratio for Pinions operate w/Formate cutters 2 to 1
Max Gear Pitch Diameter: (30 deg spiral angle)
10 to 1 ratio : 18"
2 to 1 ratio:16"
1 to 1 ratio: 12.75"
Face Width Maximum:2.75"
number of Teeth: 5-150
Diametral Pitch coarsest:2 / 12.7 Mod.
work spindle
Diameter of taper large end :3 29/32"
taper per foot:39/64"
depth of taper:6"
Diameter of hole through spindle:3 1/16"
Diameter of Spindle Nose:5 1/2"
cutter diameters:6", 7.5", 9" & 12"
Work Head Settings
Max offset above center:4.5"
Max offset below center:4.5"
Max dist mach center to spindle nose:13.5"
Min dist mach center to spindle nose:2.5"
machine floor space:75" x 114"
machine weight:23,000 lbs
Machine is equipped with items as photographed
- Roughing and finishing machine!!
-change gears and tooling in cabinet
-books and manuals provided
3
ID
MA35499
Make
Gleason USA
Model
645
YOM
Condition
Good Condition
Photo
See Photo
pairs are: REF 1 (finisher) + REF 2 (rougher), 2nd pair is REF 3 (finisher) + REF 4 (rougher) and 3rd pair is REF 5 (finisher) + REF 6 (rougher)
- max gear diameter 745,5 mm
- max radial setting 266,7 mm
- pitch-coarsest 16,9 mod
- full dept max 31,8 mm
- max face width 116,8 mm
- index range 5-80 inclusive
- diameter of taper hole at large end 152,4 mm
- taper per foot 19,0 mm
- depth of taper 152,4 mm
- diameter of hol through spindle 127,0 mm
- cutter diameter 9, 12, 16 and 18 inches
- max offset above center 114,3 mm
- max offset bellow center 114,3 mm
- max machine center to spindle nose 596,9 mm
- cutter speeds 19-167 stepless
- feeds infinitely variable from 7 s per tooth minimum
- dimensions 4600x3000x2800 mm
- weight appr. 24 t for rougher + hydraulics, change gears, other small items
- weight appr. 25 t for finisher + hydraulics, change gears, other small items
- without knife holders (heads)
- change gears
- hydraulic unit
- cooling system
- chip conveyor
- cams
- not used in the past 15 years, served only as reserve machines
- we have got some books to all the 6 machines and also found some books in the electric cabinets
MARKS:
- missing on REF 6 (rougher): 1 electric motor and 1 pump from the chip conveyor station
Quantity: 6 pieces
4
ID
MA35490
Make
Gleason USA
Model
112
YOM
199
Condition
Good Condition
Photo
See Photo
Maximum Working Diameter: 267 mm
Module:10.2
Machining Diameter:304.8 mm
Cone Distance:133 mm
Face Width:41 mm
Full Depth:19 mm
Number Of Teeth:20 - 150
Diameter Of taper Hole At Large:100 mm
Taper Per Foot:15 mm
Depth of Taper:51 mm
Diameter of Hole Through Spindle:79 mm
5
ID
MA35143
Make
Russian
Model
5C280
YOM
Condition
Good Condition
Photo
See Photo
cutting head by the rolling or plunge-in method.
The largest diameter of the workpiece, mm 800
The largest outer circumferential module, mm 16
The largest outer height of the tooth, mm 36
The largest average taper distance, mm 360
The largest gear rim width, mm 125
The smallest pitch cone angle, ° 5
The number of teeth of the product 5-150
The largest hypoid displacement, mm - up 125 - down 125
Diameter of the taper bore of the work head spindle, mm 153
Distance from the end of the work head spindle to the center of the semiautomatic device, mm 135-600
Nominal diameter of gear cutting heads, mm 160; 200; 250; 315; 400; 500
The largest radial setting of the tool spindle relative to the cradle axis, mm 320
Tool spindle rotation frequency, rpm. 18-172
Cycle time, from 7 or more
Power of the electric motor of the main movement, kW 7.5
Total power of installed electric motors, kW 17
Machine dimensions, mm
- length 3485
- width 3730
- height 2860
Machine weight, kg 16 395
6
ID
MA35108
Make
Gleason USA
Model
463
YOM
1981
Condition
Good Condition
Photo
See Photo
Modul - 12,5
Working diameter - 860 mm
There are 4 machines available
7
ID
MA34795
Make
Russian
Model
5A284
YOM
1985
Condition
Good Condition
Photo
See Photo
Work piece diameter , mm — 1600
Module , mm — 30
Weight of machine is 43 ton
8
ID
MA34565
Make
Gleason USA
Model
118
YOM
Condition
Good Condition
Photo
See Photo
There are 3 such machines available.
Max. cone distance - 230 mm
Number of teeth - 5-150
Diameter of taper hole at large end - 100 mm
Diameter of hole through spindle - 78 mm
Diameter of spindle nose - 140 mm
Floor space - 1900x2900 mm
Net weight - 10750 kg
9
ID
MA34210
Make
Russian
Model
5C23P
YOM
1984
Condition
Good Condition
Photo
See Photo
Designed for cutting small-modulus conical and hypoid wheels with circular teeth by running-in. The largest product diameter, mm 125 The largest external circumferential module, mm 2.5 The largest average cone distance, mm 75
10
ID
MA34022
Make
Saratov
Model
5C270
YOM
Condition
Good Condition
Photo
See Photo
Max. gear wheel diameter, mm 500
Module, mm 8
Max. gear wheel tooth depth, mm 22
Max. gear wheels cone distance, mm 220
Max. gear ring width, mm 80
Inclination angle of tooth: any
Number of wheel teeth 5...150
Min. angle of dividing cone (pitch), degrees 5
Stock angle, degrees 5...90
Distance between spindle and machine center, mm:
- max. (stock angle 5 degrees) 450
- min. (stock angle 90 degree) 75
Max. hypoid movement, mm:
- upwards 80
- downwards 80
Table diversion to edge, mm 100
Nominal diameter of gear - cutting heads, mm 100, 125, 160, 200, 250, 320, 400
Tools rotation speed range, rot/min 26...210
Total power required, kW 13,2
Voltage, V 380
Frequency, Hz 50
Main motor power, kW 4
Machine dimensions, mm 2885 x 2570 x 1995
Machine weight, kg 8750
11
ID
MA33833
Make
Gleason USA
Model
503
YOM
Condition
Good Condition
Photo
See Photo
There are 2 such machines available.
Gear diameter – 266mm
Pinion diameter – 152mm
Offset of gear spindle above or below center of pinion spindle – 95mm
Pinion spindle diameter of taper hole at large end – 100mm
Depth of taper – 76mm
Spindle hole diameter – 63mm
Weight – 4195kg
12
ID
MA33821
Make
Gleason USA
Model
650
YOM
Condition
Good Condition
Photo
See Photo
There are 3 such machines available.
Modul - 23
Diameter - 863mm
Weight - 24 800kg
13
ID
MA33437
Make
Gleason USA
Model
666
YOM
Condition
Good Condition
Photo
See Photo
Capacity:
Outside Cone Distance :
Maximum - 355.6 mm
Minimum - 101.6 mm
Maximum Gear Pitch Diameter :
Manual Machine - 660.4 mm
Machine with Automatic Loader - 508.0 mm
Maximum Full Depth - 31.75 mm
Doarsest pitch - 16.9 Mod
Maximum Face width - 106.7 mm
Maximum Thickness of Gear Blanks Front to Gear Back for machine with Automatic Loader - 111.1 mm
Maximum Stripping Distance for Removal of Gear from Arbor for mahine with Automatic Loader - 76.2 mm
Outter Diameters - 200 mm, 250 mm
320 mm, 400 mm
500 mm
Workhead setting Adjustment Range - 203.2 mm
Total Workhead Axial Movement
(head setting plus withdraw) - 508.0 mm
Work Spindle (18 taper)
Diameter of taper hole at large end - 86.92 mm
Taper per foot - 12.70 mm
Depth of Taper - 15.875 mm
Maximum Chucking Load - 17,690 kg
Cutter spindle (14 taper)
Diameter of taper Nose at Large End - 58.22 mm
Taper per Foot - 12.70 mm
Length of Nose - 15.875 mm
Electrical Equipment
Main Drive Motor - Two Speedn - 1500/750 rpm
Hydraulic Motor - 1000 rpm
Coolant Motor - 1000 rpm
Misoellaneous
Floor Space:
Manual machine - 226 x 307 cm
Machine with automatic loader - 257 x 361 cm
height
Manual machine - 224 cmm
machine with automatic loader - 244 cm
14
ID
MA33436
Make
Gleason USA
Model
645
YOM
Condition
Good Condition
Photo
See Photo
Max wheel diameter : 745,5 mm,
Gear width : 116,8 mm,
Max module : 16,9,
Cutter speeds : 18,9-167,2 rpm,
Spindle bore : 127 mm,
Voltage freuency : 380-50 V/Hz,
Hydraulic motor : 5 & 1,7 kW,
Coolant pump drive : 1,5 kW,
Number of teeth : 5-80,
Dimensions of the machine : 5000 x 3500 x 2100 mm,
Weight of the machine : 26500 kg.
15
ID
MA33435
Make
Gleason USA
Model
641
YOM
Condition
Good Condition
Photo
See Photo
Make : Gleason
Model : 641
16
ID
MA32930
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Max cone distance (30 degree angle and 300 mm cutter): 228 m
Max extreme ratio: 10 to 1
Max gear pitch diameter (30 degree spiral angle):
-Ratio 10 to 1: 457 mm
-Ratio 2 to 1: 406 mm
-Ratio 1 to 1: 323 mm
Diametral pitch (coarsest): 12,7 mod.
Max full depth: 25,4 mm
Max face width: 69,9 mm
Number of teeth: 5 to 150
WORK SPINDLE
Diameter of taper hole at large end: 100 mm
Taper per foot: 39/1600 mm
Depth of taper: 150 mm
Diameter of spindle nose: 137,5 mm
CUTTER DIAMETER
Diameter: 125 mm; 150 mm; 187,5 mm; 225 mm; 300 mm
WORKHEAD SETTINGS:
Max offset above center: 112,5 mm
Max offset bellow center: 112,5 mm
Distance from machine center to nose of spindle:
-Max: 337,5 mm
-Min: 62,5 mm
Floor space: 2560x1980 mm
Height: 1620 mm
Net weight: 10977 kg
There is 1 such machine available.
The machine was used for finishing work in a labrotary.
Change gears are not available.
17
ID
MA32497
Make
Gleason USA
Model
650
YOM
1979
Condition
Good Condition
Photo
See Photo
The Gleason No 650 Hypoid Generator is a machine designed and built for cutting large Hypoid, Spiral and Zerol Bevels and mating gears up to 34" diameter of any ratio up to 10:1
Comes with Modified Roll Mechanism, Hydraulic Work Clamping, Coolant Pump, Set of Change Gears, 4 Index Cams, Chip Conveyor
Diameter 863 mm
Module 23 mm
Axial travel 0 mm
18
ID
MA31874
Make
Gleason USA
Model
106
YOM
Condition
Good Condition
Photo
See Photo
Cone Distance, max. (30" spiral angle & 7-1/2" cutter): 4-1/4"
Gear Pitch diameter, max.: 10 to 1
10 to 1 ratio: 8-1/2"
2 to 1 ratio: 7-1/2"
1 to 1 ratio: 6"
Diametral Pitch (coarsest): 4
Full depth, max: 625"
Face width, max.: 1-1/4"
Number of teeth: 5 to 150
WORK SPINDLE
Dia. of taper hole at large end: 3-29/32"
Taper per foot: 89/64"
Depth of taper: 6"
Dia. of hole through spindle: 2-7/16"
Dia. of spindle nose: 5-11/82"
Cutter Diameter: 3-1/2", 4-1/2", 5", 6", 7-1/2"
WORK HEAD
Offset above center, max.:8"
Offset below center, max.:8"
Dist. from machine center to nose of spindle, max.:9"
Dist. from machine center to nose of spindle, min.: 1-1/4"
Cutter Speeds: 54-418 RPM
Feeds (seconds per tooth): 5 - 73 seconds
Feed motor: 5 HP, 1800 RPM
Hydraulic motor: 1 HP, 1800 RPM
Coolant motor: 1/2 HP, 8600 RPM
Floor Space : 84" x 61"
Net Weight :15,500 lbs
19
ID
MA31855
Make
Gleason USA
Model
106
YOM
Condition
Good Condition
Photo
See Photo
Max.cone distance: 10.8 cm, (0° to 35° spiral angle, 187.5 cutter, 31.25 face, Max. pitch diameter (shafts at 90°): - 0° to 35° spiral angle, 10:1 ratio: cm. 21.5, - 0° to 35° spiral angle, 2:1 ratio: cm. 19, - 0° to 35° spiral angle, 1:1 ratio: cm. 15.2, Max. face width: cm. 3.2, Diametral pitch, coarsest: mod. 6.3 (4 D.P., MACHINE LIMITS Max. full depth: cm. 1.26, Displacement of cutter axis from cradle axis: cm. 0 to 15.2, Root angle setting: -12° to 90°, Index range: 5 to 97, Cutter diameters: 3.8, 5.1, 8.9, 11.4, 15.2, 19 cm, Work head offset, above or below center: cm. 7.5, Sliding base adjustment: - Advance from machine center line: cm. 5.1, - Withdraw from machine center line: cm. 7.5, Work spindle nose to machine center line: cm. 3.2 to 22.8, WORK SPINDLE Diameter of taper hole at large end: cm. 9.9, Taper: 1:18.5, Depth of taper: cm. 15.2, Diameter of hole through spindle: cm. 6.2, SPEEDS AND FEEDS Feed (seconds per tooth): 4.9 to 68.6, Cutter speeds (feet or meters per minute): 25 to 133 m/min (74 to 380 feet), ELECTRICAL EQUIPMENT Main motor: 5 horsepower, 1800 rpm (1500 rpm for 50 cycle), Coolant pump: 1½ horsepower, 3600 rpm (3000 rpm for 50 cycle), Hydraulic pump: ¾” horsepower, 1800 rpm (1500 rpm for 50 cycle), WEIGHT AND DIMENSIONS Weight: kg. 648 (14,300 lbs.), Floor space: cm. 159x214.
20
ID
MA30247
Make
Gleason USA
Model
200HG
YOM
Condition
Good Condition
Photo
See Photo
Extreme ratio: 10:1
Root angle range ( B axis): -5 deg to 90 deg,
Equivalent root angle range: -8 deg to 90 deg,
Full depth (max): 16.00 mm,
Face width (max): 40.65 mm,
Range of tooth numbers: 5 to 200 inclusive
35° spiral angle gear using maximum,
Wheel diameter: 7.5 diameter wheel,
At the following rations: 1:1 (171.45 mm),
2:1 (215.90 mm)
5:1 (215.90 mm)
Wheel diameters: 2.0" to 7.5"
Machine specifications
X - horizontal: -6" to 4" (-152 to 102 mm)
Y vertical: -4" to 7" (-102 to 178 mm),
Z sliding base travel 2" to 12 " (51 to 304 mm)
Machine center to work
Spindle face: 114.30 mm,
Axes speeds
X horizontal : 125 mm/sec,
Y vertical: 125 mm/sec,
Z sliding base travel : 125 mm/sec
A work spindle RPM: 0 to 30
B wheel spindle: 0 to 30 deg/sec,
C wheel spindle: 1000 to 6000 RPM,
D dresser spindle: 1500 to 8000 RPM,
Work spindle dimensions
Diameter to taper hole- large end 3-29/32" (#39 taper)
Taper per foot: 39/64"
Depth of taper: 3"
Electrical equipment (motors)
X horizontal digital servo drive fanuc 5S/3000 10K
Y vertical dig servo drive fanuc 5 S/3000 10 K W/brake
Z sliding base dig servo drive fanuc 5S/3000 10K
A-work spindle dig servo drive fanuc 5 S/3000 10K
B- swing ing base dig servo fanuc 5 S/3000 10K 2 K sealed,
C wheel spdl dig servo fanuc 15P/1024 precision shaft
Dresser digital servo drive fanuc B0.3
Scavenger pump AC 3HP
Hydraulic pump AC 3HP
Chiller AC
Miscellaneous
Floor space (base machine only ) L x W: 95.75" x 63.5"
Floor space (base machine only) L x W: 2432 x 1613 mm,
Height: 90.75" (2305 mm),
Weight (approx): 19,000 LBS (10,140 KGS),
suitable for the hard finishing of spiral bevel, zerol
bevel,and hypoid gears and pinions up to 8"
(215.90 mm) pitch diameter at 5:1 ratio, 1.6"
(40.65 mm) maximum face-width,utilizing non-dressable
plated cbn wheels, or dressable wheels such as
conventional aluminum oxide, sg, and/or vitrified
CBN type
Equipment:
machine furnished with free standing, air
conditioned electrical enclosure, w/operator's
controls located at machine front, adjacent to
access door
- ge-fanuc series 150 computer control with gear
grinding software, 10.4" lcd flat color display,
storage capacity for 100 summaries, cycle fault
monitoring, and automatic setup and control of 7
axes: (a ) work spindle, (b) swinging base,
(c) wheel spindle, (d) dresser, (x) horizontal,
(y) vertical, (z) sliding base
- machine arrangement as 200hg grinder
- manual stock dividing system
(missing manual stock-divider & mounting bracket)
- wheel dressing unit (dressing cycle via cnc)
- work-piece adaptor on work-spindle
- totally enclosed work-area guarding w/powered
access door
- work chamber lighting
- hydraulic work piece chucking with draw-rod
- flooded suction-type hydraulic unit
- smoke and mist collector/system
- wheel lifting device
- grinding wheel length gauge
- dressing tool wear gauge
- rough wheel dressing tools
- finish wheel dressing tools
- complete coolant and filtration unit w/chiller for
grinding & hydraulic oil.
- assorted wheel adaptors and mounting equipment
- balance measuring device
- full complement of electrics, (motors/controls)
electrical / hydraulic controls to ec
specifications (400 volt, 50 hz)
- good assortment of electrical spares & drives for 150 control
- misc. wrenches, spanners, operator's tools
- machine leveling shoes,
21
ID
MA29157
Make
Gleason USA
Model
503
YOM
1968-1969/66
Condition
Good Condition
Photo
See Photo
Maximum gear diameter: 266 mm,
Maximum pinion diameter: 152 mm,
Pinion spindle diameter of taper hole at large end: 100 mm,
Pinion spindle diameter of taper: 76 mm,
Gear spindle diameter of hole thru spindle: 63 mm,
Gear spindle taper per foot: 13 mm,
Gear spindle diameter of hole thru spindle: 58 mm,
Floor space (W x L): 1920 x 7550 mm,
Height of machine: 2300 mm,
Net weight (approximate): 4,0 tons,
Quantity: 8 nos
22
ID
MA28480
Make
Russian
Model
5C280P
YOM
1982
Condition
Good Condition
Photo
See Photo
Max. gear wheel diameter: 800 mm,
Module: 12 mm,
Max. gear wheel tooth depth: 35 mm,
Max. gear wheels cone distance: 360 mm,
Max. gear ring width: 125 mm,
Number of wheel teeth: 5....150,
Nom. angle of dividing cone (pitch): degrees 5,
Stock angle: degrees 5..90,
Nominal diameter of gear- cutting heads: 160,200,250,320,400,500 mm,
Tools rotation speed range: 18...135 rot/min,
Total power required: 13,2 kW,
Voltage: 380 V,
Frequency: 50 Hz,
Main motor power: 7,5 kW,
Total power required: 16,22 kW,
Machine dimensions: 3235 x 2180 x 2200 mm,
Machine weight: 15380 kg.
23
ID
MA28311
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Maximum pitch diameter : 450 mm,
Maximum rate : 10/1 mm,
Maximum cone distance : 225 mm,
Work head angle : 12 deg -90 deg,
Diameter pitch coarsest : 2,
Face width maximum : 2-3/4" mm,
Number of teeth : 5-150 mm,
Spindle :
Diameter of taper hole , large end : 3-29/32" mm,
Taper per foot : 39/64" mm,
Depth of taper : 150 mm,
Diameter of hole thru : 3-1/16" mm,
Spindle nose to centerline : 5-12" mm,
Speeds and feeds:
Cutter speeds, feet per min : 17-115 RPM,
Feeds, seconds per tooth : 80 seconds,
Electrical equipment :
Feed motor : 5 HP, 1800 RPM,
Hydraulic pump motor : 3/4 HP, 1800 RPM,
Coolant motor : 1/2 HP, 3600 RPM,
Floor space : 1875 x 2850 mm,
Net weight : 23,700 #,
Shipping weight , boxed for export :
1 case -10'6" x 8'1" x 6'5" : 25,300 #,
Gear Generator Finisher,
24
ID
MA28230
Make
Russian
Model
528S(528C)
YOM
1967
Condition
Good Condition
Photo
See Photo
Work piece diameter 800 mm, module 16.
25
ID
MA27546
Make
Russian
Model
CT280
YOM
1989
Condition
Good Condition
Photo
See Photo
Work piece maximum diameter : 800 mm,
The greatest external district module : 16 mm,
The greatest external height of a spur : 36 mm,
The greatest average conical distance : 360 mm,
The greatest width of a gear wreath : 125 mm,
The least corner of a dividing cone : 5 degree,
Number of spur : 5-150,
The greatest hypoid displacement :- up : 125 mm, down : 125 mm,
Distance from an end face of a spindle of a wheel head of a product up to the center of a semiautomatic device : 135-600 mm,
Nominal diameter of spur-carved heads : 160; 200; 250; 315; 400; 500 mm,
The greatest radial installation of a tool spindle concerning an axis : 320 mm,
Frequency of rotation of a tool spindle : 18-172 rpm,
Time of a cycle с 7 And more,
Main electric motor power : 7,5 kW,
Total power of the installed electric motors : 17 kW,
Machine overall dimensions :-
Length : 3485 mm,
Width : 3730 mm,
Height : 2860 mm,
Machine weight : 16,395 kg.
26
ID
MA27545
Make
Russian
Model
CT280
YOM
1981
Condition
Good Condition
Photo
See Photo
Work piece maximum diameter : 800 mm,
The greatest external district module : 16 mm,
The greatest external height of a spur : 36 mm,
The greatest average conical distance : 360 mm,
The greatest width of a gear wreath : 125 mm,
The least corner of a dividing cone : 5 degree,
Number of spur : 5-150,
The greatest hypoid displacement :- up : 125 mm, down : 125 mm,
Distance from an end face of a spindle of a wheel head of a product up to the center of a semiautomatic device : 135-600 mm,
Nominal diameter of spur-carved heads : 160; 200; 250; 315; 400; 500 mm,
The greatest radial installation of a tool spindle concerning an axis : 320 mm,
Frequency of rotation of a tool spindle : 18-172 rpm,
Time of a cycle с 7 And more,
Main electric motor power : 7,5 kW,
Total power of the installed electric motors : 17 kW,
Machine overall dimensions :-
Length : 3485 mm,
Width : 3730 mm,
Height : 2860 mm,
Machine weight : 16,395 kg.
27
ID
MA27544
Make
Russian
Model
5C280P
YOM
1999
Condition
Good Condition
Photo
See Photo
Work piece maximum diameter : 800 mm,
The greatest external district module : 16 mm,
The greatest external height of a spur : 36 mm,
The greatest average conical distance : 360 mm,
The greatest width of a gear wreath : 125 mm,
The least corner of a dividing cone : 5 degree,
Number of spur : 5-150,
The greatest hypoid displacement :- up : 125 mm, down : 125 mm,
Distance from an end face of a spindle of a wheel head of a product up to the center of a semiautomatic device : 135-600 mm,
Nominal diameter of spur-carved heads : 160; 200; 250; 315; 400; 500 mm,
The greatest radial installation of a tool spindle concerning an axis : 320 mm,
Frequency of rotation of a tool spindle : 18-172 rpm,
Time of a cycle с 7 And more,
Main electric motor power : 7,5 kW,
Total power of the installed electric motors : 17 kW,
Machine overall dimensions :-
Length : 3485 mm,
Width : 3730 mm,
Height : 2860 mm,
Machine weight : 16,395 kg.
28
ID
MA27210
Make
Russian
Model
CT270
YOM
1989
Condition
Excellent
Photo
See Photo
Max. gear wheel diameter : 500 mm,
Module : 8 mm,
Max. gear wheel tooth height : 22 mm,
Max. gear wheels cone distance : 220 mm,
Max. gear ring width : 80 mm,
Inclination angle of tooth : any,
Number of wheel teeth : 5...150,
Min. angle of dividing cone : 5 degrees,
Table diversion to edge : 100 mm,
Nominal diameter of gear - cutting heads : 100, 125, 160, 200, 250, 320, 400 mm,
Machine dimensions : 2885 x 2570 x 1995 mm,
Machine weight : 9000 kg.
For finishing bevel and hypoid gears with circular teeth.
Qty :1 nos.
29
ID
MI6103
Make
Gleason USA
Model
16
YOM
Condition
Good working condition
Photo
See Photo
Cone distance maximum : 305 mm,
Pitch angle maximum (shafts at 90 degree) : 84 degree 18',
Minimum : 5 degree 42',
Extreme ratio : 10:1,
Diametral pitch : 8.5 mod,
Index range : 5 to 100 inclusive and most numbers up to 200,
Diameter of taper hole at large end : 99.22 mm,
Taper per foot : 15.48 mm,
Depth of taper : 152.4 mm,
Diameter through hole : 77.79 mm,
Spindle nose to machine center : 63.5 to 381 mm,
Cutter speed (stroke per minute) : 64 to 495,
Feeds (seconds per tooth) : 10 to 131 mm,
Main motor : 50 Hz,
Hydraulic pump motor : 1500 rpm,
Cutting oil pump motor : 1000 rpm,
Floor space : 1920 x 1420 mm,
Shipping weight boxed for export : 7,455 kg,
Size of case : 2440 x 1880 x 1960 mm,
Net Weight : 6,863 kg.
Qty : 2 nos.
30
ID
MA27143
Make
Gleason USA
Model
463
YOM
Condition
Good Condition
Photo
See Photo
Max pitch diameter : 863 mm,
Max face width: 76 mm,
Cone distance (max. 30˚ spiral angle and 12" diameter wheel) - 15"/(381mm)
Maximum pitch angle, shafts at 90˚ - 71˚ 34'
Minimum pitch angle, shafts at 90˚ - 5˚ 42'
Extreme ratio, shafts at 90˚ - 3 to 1
Maximum pitch diameter: (90˚ shafts):
Spiral angle 0˚, ratio 1 to 1 - 15.5"/(393.7mm)
Spiral angle 0˚, ratio 3:1 - 23"/(584.2mm)
Spiral angle 30 ˚, ratio 1:1 - 21"/(533.4mm)
Spiral angle 30˚, ratio 3:1 - 31.5"/(800.1mm)
Spiral angle 45˚, ratio 1:1 - 22.5"/(571.5mm)
Spiral angle 45˚, ratio 3:1 - 34"/(863.6mm)
Coarsest diametral pitch / metric module 2 DP / 12.7
Maximum face width 3"/(76.2mm)
Quantity : 4 nos,
with full set of dressers, hydraulic chucking, guards, coolant.
31
ID
MA27084
Make
WMW Modul
Model
ZFTKK500/3A
YOM
1989 (both)
Condition
Good Condition
Photo
See Photo
Max outer length of pitch cone : 270 mm,
Max outer edge modul : 16 mm,
Max outer diameter of pitch circle : 380...540 mm,
Number of teeth : 6...100,
Max tooth's length : 78 mm,
Quantity : 2 nos
32
ID
MA26984
Make
KLINGELNBERG
Model
AMKU500
YOM
1987/2011
Condition
Good Condition
Photo
See Photo
Wheel diameter max : 500 mm,
Wheel width : 100 mm,
Module max : 8.5,
Module min : 1.5,
Axial offset : +/- 75 mm,
Number of teeth : 5-120,
Tool speeds max : 200 U / min,
Main drive motor : 20 kW,
Total power requirement kW,
Space requirement approx : 5.08 x 3.05 x 2.48 m,
Machine weight about : 15.9 t.
Additional information :-
Headstock : Spindle taper : 160 mm,
Faceplate diameter : 400 mm,
Spindle bore : 150 mm,
Max. Length of the receiving mandrel : 450 mm,
Immersion Feed speed : 0.1 to 50 mm / min.
Biggest Tauchweg : 50 mm,
Wälzvorschubgeschwindigkeit : 1-50 ° / min.
The following work programs can be run on the machine :-
Set up,
Diving followed by profile rolling (for cogging normally be submitted Cyclo-spiro-conical gears)
Twice dipping with subsequent profile rolling (for example, if sprocket must be integrated, the tooth width beyond the theoretically calculated)
Diving with temporarily superimposed rolling and then rolling profile (eg if kleinzahlige pinion are made with large tooth widths)
Diving (for generating Tellerrädernnach the Zyklomet method)
Profile rolling
Hydraulic. Workpiece clamping, complete set of change gears.
33
ID
MA26922
Make
Stanko-Russia
Model
5S270P
YOM
1988-1990
Condition
Very good condition
Photo
See Photo
Work piece diameter : 500 mm,
Module : 8 mm,
Tooth depth : 22 mm,
Tooth width : 80 mm,
Number of teeth : 5-150 ,
Distance work piece spindle/top of cone : 75-450 mm,
Pitch cone length : 220 mm,
Cutter spindle : 26-210 rpm,
Total connected load : 11,4 kW,
Machine weight : 9000 kg,
Quantity : 4 nos.
34
ID
MI6038
Make
WMW Modul
Model
ZFTKK500/2U
YOM
Condition
Good Condition
Photo
See Photo
Max gear dia at ratio 1:9 and 1:1 : 500 mm and 355 mm,
Pitch cone length : 250 mm,
Module range : 1 - 13,
Tooth width : 71 mm,
Tooth depth max : 0 - 06 mm,
No of teeth : 6 - 100 mm,
Swivel angle of the workpiece head : + 60 to + 90 °
Pitch cone angle max : 90°,
Hob spindle tilt : 22°,
Axial shift of the workpiece spindle : +/- 80 mm,
Distance between workpiece spindle and cone tip : 80 – 450 mm,
Workpiece spindle taper, metr. Cone : 100 mm,
Tool/cutter head dia : 6 – 375 mm,
Excentricity : 0 – 200 mm,
Vertical feed range : 0.5 – 6 mm,
Weight of the machine : 10,500 kg.
Machine are complete with change gears and Chip Conveyor.
35
ID
MA26787
Make
Gleason USA
Model
16
YOM
Condition
Good Condition
Photo
See Photo
Cone distance maximum : 305 mm,
Pitch angle maximum (shafts at 90 degree) : 84 degree 18',
Minimum : 5 degree 42',
Extreme ratio : 10:1,
Diametral pitch : 8.5 mod,
Index range : 5 to 100 inclusive and most numbers up to 200,
Diameter of taper hole at large end : 99.22 mm,
Taper per foot : 15.48 mm,
Depth of taper : 152.4 mm,
Diameter through hole : 77.79 mm,
Spindle nose to machine center : 63.5 to 381 mm,
Cutter speed (stroke per minute) : 64 to 495,
Feeds (seconds per tooth) : 10 to 131 mm,
Main motor : 50 Hz,
Hydraulic pump motor : 1500 rpm,
Cutting oil pump motor : 1000 rpm,
Floor space : 1920 x 1420 mm,
Shipping weight boxed for export : 7,455 kg,
Size of case : 2440 x 1880 x 1960 mm,
Net Weight : 6,863 kg.
Qty : 2 nos.
36
ID
MA26565
Make
Gleason USA
Model
463
YOM
1980
Condition
Good Condition
Photo
See Photo
Distance (max. 30˚ spiral angle and 12"
diameter wheel) - 15"/(381mm)
Maximum Pitch Angle, shafts at 90˚ - 71˚ 34'
Minimum Pitch Angle, shafts at 90˚ - 5˚ 42'
Extreme ratio, shafts at 90˚ - 3 to 1
Maximum Pitch Diameter: (90˚ shafts):
spiral angle 0˚, ratio 1 to 1 - 15.5"/(393.7mm)
spiral angle 0˚, ratio 3:1 - 23"/(584.2mm)
spiral angle 30 ˚, ratio 1:1 - 21"/(533.4mm)
spiral angle 30˚, ratio 3:1 - 31.5"/(800.1mm)
spiral angle 45˚, ratio 1:1 - 22.5"/(571.5mm)
spiral angle 45˚, ratio 3:1 - 34"/(863.6mm)
Coarsest Diametral Pitch / Metric Module 2 DP / 12.7
Maximum Face Width 3"/(76.2mm)
SPINDLE:
Diameter of Taper Hole at Large End 3-29/32"
Taper (Per Ft) 39/64"
Depth of taper 6"/152mm
Diameter of hole through spindle 3-1/16”
WHEEL DIAMETER:
5-1/2"(139,7 mm) to 13-1/2" (342,9 mm)
(can be exceeded in some cases)
WORKHEAD SETTINGS:
Max. offset above/below center 4.5" / 114,3 mm
Max./ min dist. from machine center to spindle nose 20-1/2 (521 mm) - 3" / (76 mm),
Feed Rate (Seconds Per Tooth) 1.9-11.8
Total Capacity of motors 21HP / 15,6 kW
Approx. Floor Space 135" x 81" (3429x2057mm)
Approx. Machine Height 97" (2464mm)
Approx. Machine Net Weight 23,000 lbs. (10,422 kg)
Qty : 12 nos.
37
ID
MA26504
Make
Gleason USA
Model
22
YOM
Condition
Good Condition
Photo
See Photo
Machine capacity :
Longest cone distance : 275 mm,
Largest pitch angle : 90 deg,
Smallest pitch angle (without chamfering or burring attachments) : 45 deg,
Largest pitch diameter : 1 to 1 Ratio : 15/1/2" mm,
12 to 1 Ratio : 550 mm,
Largest pitch (diametral) : 1 1/2 D.P.,
Max face width : 100 mm,
Index range (number of teeth ) : 31 to 78 ,
Feed (seconds per tooth) : 5 to 40 mm,
Work spindle :
Diameter of tapered nose (large end ) 6 7/8" mm,
Length of tapered nose : 3/4" mm,
Taper per foot : 1/2" mm,
Diameter of hole through : 50 mm,
Spindle nose to center line of machine : 4 1/2" to 200 mm,
Cutter :
Diameter : 225, 300,450 mm,
Cutter speeds : 100 to 150 mm ,
Main motor : 10 H.P., 1800 R.P.M.,
Floor space : 2100 x 2575 mm,
Weight : 18,500 lbs,
Rougher and Finisher.
With various index plate, with instruction book.
Qty : 2 nos.
38
ID
MA26502
Make
Gleason USA
Model
463
YOM
1980
Condition
Good Condition
Photo
See Photo
Distance (max. 30˚ spiral angle and 12"
diameter wheel) - 15"/(381mm)
Maximum Pitch Angle, shafts at 90˚ - 71˚ 34'
Minimum Pitch Angle, shafts at 90˚ - 5˚ 42'
Extreme ratio, shafts at 90˚ - 3 to 1
Maximum Pitch Diameter: (90˚ shafts):
spiral angle 0˚, ratio 1 to 1 - 15.5"/(393.7mm)
spiral angle 0˚, ratio 3:1 - 23"/(584.2mm)
spiral angle 30 ˚, ratio 1:1 - 21"/(533.4mm)
spiral angle 30˚, ratio 3:1 - 31.5"/(800.1mm)
spiral angle 45˚, ratio 1:1 - 22.5"/(571.5mm)
spiral angle 45˚, ratio 3:1 - 34"/(863.6mm)
Coarsest Diametral Pitch / Metric Module 2 DP / 12.7
Maximum Face Width 3"/(76.2mm)
SPINDLE:
Diameter of Taper Hole at Large End 3-29/32"
Taper (Per Ft) 39/64"
Depth of taper 6"/152mm
Diameter of hole through spindle 3-1/16”
WHEEL DIAMETER:
5-1/2"(139,7 mm) to 13-1/2" (342,9 mm)
(can be exceeded in some cases)
WORKHEAD SETTINGS:
Max. offset above/below center 4.5" / 114,3 mm
Max./ min dist. from machine center to spindle nose 20-1/2 (521 mm) - 3" / (76 mm),
Feed Rate (Seconds Per Tooth) 1.9-11.8
Total Capacity of motors 21HP / 15,6 kW
Approx. Floor Space 135" x 81" (3429x2057mm)
Approx. Machine Height 97" (2464mm)
Approx. Machine Net Weight 23,000 lbs. (10,422 kg)
Qty : 4 nos (One is CNC).
39
ID
MA26488
Make
Gleason USA
Model
YOM
Condition
Good Condition
Photo
See Photo
3"
40
ID
MA26486
Make
Gleason USA
Model
112
YOM
Condition
Good Condition
Photo
See Photo
Diameter pitch : 10.2 mod,
Max cone distance : 133 mm,
Max pitch angle : 90 degree,
Min pitch angle : 45 degree,
Min extreme rato : 2-1/2:1,
Pitch diameter : 267 mm,
Face width : 41 mm,
Full depth : 19 mm,
Number of teeth : 20-150,
Diameter of taper hole at large end : 100 mm,
Taper per foot : 15 mm,
Depth of taper : 51 mm,
Diameter of hole through spindle : 79 mm,
Cutting diameter : 150 x 190 x 230 mm,
Cutter speeds : 3m to 13.4m,
Feeds : 3.2-9.2,
Electrical equipment :-
main motor : 3Hp, 900 rpm,
Hydraulic motor : 3Hp, 1200 rpm,
Coolant motor : 1Hp, 1800 rpm,
Index hydraulic motor : 1/2 Hp, 1800 rpm,
Lubricating motor : 1/4Hp, 1800 rpm,
Floor space : 174 x 312 cm,
Net weight : 10886 kg.
Serial number : 607712 / 605011
Qty : 2 nos.
41
ID
MA26485
Make
Gleason USA
Model
YOM
Condition
Good Condition
Photo
See Photo
1) Model : 613 - Rougher
2) Model : 614 - Finisher
Serial number : 724202 / 724301
Pinion o.d. max : 177.8 mm,
Pitch diameter of mate : 266.7 mm,
Cone distance : 133.3 mm,
Whole depth : 19 mm,
Face width : 44.5 mm,
Tooth numbers : 6-25,
Ratio range : 1.9-6.0,
Machine Capacity :-
Tilt angle : 40,
Root angle : -300 to +300 mm,
Machine offset : 82.6 mm,
Sliding base advance : 25.4 mm and withdraw : 63.5 mm,
Radial : 127 mm,
Work Spindle :-
Depth of taper : 150 mm,
Speeds and feeds :-
Cutting speeds : 600 sfpm,
Feed : 3.5 sec/tooth,
Electrical Equipment :-
Hydraulic motor : 1500 rpm,
Scavenger motor : 1500 rpm,
Coolant motor : 1500 rpm,
Cutting motor : 1000 rpm,
Servo pump drive motor : 1500 rpm,
Miscellaneous :-
Floor space including electrical control box : 290 x 231 cm,
Weight net : 12202 kg.
Weight gross : 13472 kg.
42
ID
MA26484
Make
Gleason USA
Model
645
YOM
Condition
Good Condition
Photo
See Photo
Max wheel diameter : 745,5 mm,
Gear width : 116,8 mm,
Max module : 16,9,
Cutter speeds : 18,9-167,2 rpm,
Spindle bore : 127 mm,
Voltage freuency : 380-50 V/Hz,
Hydraulic motor : 5 & 1,7 kW,
Coolant pump drive : 1,5 kW,
Number of teeth : 5-80,
Dimensions of the machine : 5000 x 3500 x 2100 mm,
Weight of the machine : 26500 kg.
Equipped with :-
Hydraulical workpiece clamping system,
Clamping of base slide,
Helical motion,
Generating change gears.
Serial number : 754301
43
ID
MA25976
Make
Russian
Model
5C270P
YOM
1984
Condition
Good working condition
Photo
See Photo
Max diameter of wheels : 500 mm,
max normal module : 8 mm,
Max height of wheel tooth : 22 mm,
Max cone distance of gear wheels : 220 mm,
Max width of gear ring : 80 mm,
Number of wheel teeth : 5-150,
Min angle of dividing cone : 5,
Stock angle : max:+90, min:+5,
Distance of end face from the spindle to the center : max (when stock adjustment angle is 5 degree) : 450 mm, - min (when stock adjusting angle is 90 degree) : 75 mm,
Min hypoid displacement : upper-80 mm, down-80mm,
Weight of the machine : 6 ton.
Quantity : 2 nos,
With all heads and accessories.
44
ID
MA25972
Make
Gleason USA
Model
609
YOM
1971-1973
Condition
Good Condition
Photo
See Photo
Outside cone distance : max 250 mm, min 100 mm, max gear pitch dia 500 mm, cutter dia utilized 225-450 mm, root angle 60-80 deg, face width 75 mm, number of teeth 20-75 , Equipped with :Hydraulic Chuck
Change Gears
1 Cutter Body w/Blades
Rotating Screw-Type Chip Conveyor
Coolant Tank, Pump & Piping
Qty 3 nos.
45
ID
MA25971
Make
Gleason USA
Model
608
YOM
1971-1973
Condition
Good Condition
Photo
See Photo
Outside cone distance : max 250 mm, min 100 mm, max gear pitch dia 500 mm, cutter dia utilized 225-450 mm, root angle 60-80 deg, face width 75 mm, number of teeth 20-75 , Equipped with :Hydraulic Chuck
Change Gears
1 Cutter Body w/Blades
Rotating Screw-Type Chip Conveyor
Coolant Tank, Pump & Piping
Qty 3 nos.
46
ID
MA25955
Make
Gleason USA
Model
463
YOM
Condition
Good Condition
Photo
See Photo
Distance (max. 30˚ spiral angle and 12"
diameter wheel) - 15"/(381mm)
Maximum Pitch Angle, shafts at 90˚ - 71˚ 34'
Minimum Pitch Angle, shafts at 90˚ - 5˚ 42'
Extreme ratio, shafts at 90˚ - 3 to 1
Maximum Pitch Diameter: (90˚ shafts):
spiral angle 0˚, ratio 1 to 1 - 15.5"/(393.7mm)
spiral angle 0˚, ratio 3:1 - 23"/(584.2mm)
spiral angle 30 ˚, ratio 1:1 - 21"/(533.4mm)
spiral angle 30˚, ratio 3:1 - 31.5"/(800.1mm)
spiral angle 45˚, ratio 1:1 - 22.5"/(571.5mm)
spiral angle 45˚, ratio 3:1 - 34"/(863.6mm)
Coarsest Diametral Pitch / Metric Module 2 DP / 12.7
Maximum Face Width 3"/(76.2mm)
SPINDLE:
Diameter of Taper Hole at Large End 3-29/32"
Taper (Per Ft) 39/64"
Depth of taper 6"/152mm
Diameter of hole through spindle 3-1/16”
WHEEL DIAMETER:
5-1/2"(139,7 mm) to 13-1/2" (342,9 mm)
(can be exceeded in some cases)
WORKHEAD SETTINGS:
Max. offset above/below center 4.5" / 114,3 mm
Max./ min dist. from machine center to spindle nose 20-1/2 (521 mm) - 3" / (76 mm),
Feed Rate (Seconds Per Tooth) 1.9-11.8
Total Capacity of motors 21HP / 15,6 kW
Approx. Floor Space 135" x 81" (3429x2057mm)
Approx. Machine Height 97" (2464mm)
Approx. Machine Net Weight 23,000 lbs. (10,422 kg)
Qty : 2 nos.
47
ID
MI5680
Make
WMW Modul
Model
ZFTKK500/2W
YOM
Condition
excellent working condition
Photo
See Photo
Max wheel diameter : 540 mm,
Max gear width : 78 mm,
Module : max 16, min 1,
Description Number of teeth : 6-100,
Min/max pitch cone length : 270 mm,
Min/max. pitch cone angle : 90 °,
Milling spindle turning speed range : 23 - 224 U/min,
Blade cutter head diameter : 6 - 300 mm.
48
ID
MA21958
Make
Gleason USA
Model
606
YOM
1970
Condition
Good Condition
Photo
See Photo
Description: Piece holding table motor 35 Nm X axis motor 12 Nm , X axis visualized on DRO. Net weight 6500 kg Lubrification oil tank capacity 100 Lt. Specification: Milling spindle speed 50 / 200 RPM Max. diam. Of piece 350 mm Milling spindle motor 9kw Oil tank capacity for hydraulic system 60 Lt,
49
ID
MA21807
Make
Gleason USA
Model
16
YOM
Condition
Good working condition
Photo
See Photo
- 2 machines
50
ID
MA21771
Make
Gleason USA
Model
6A
YOM
Condition
Good Condition
Photo
See Photo
Maximum Diameter Of Gears 190.5mm,
Range Of Angles 0 To 180 DEGREES,
Range Of Pinion Offset: (Above Center)31.49mm,
Range Of Pinion Offset: (Below Center)31.49mm,
Max./Min. Distance Pinion Spindle Center to Nose Of Gear Spindle 177.8/0 mm,
Max./Min. Distance Gear Spindle Center
To Nose Of Pinion Spindle 177.8/25.4mm,
Diameter Of Spindle Hole (Large End) 45.64mm,
Taper Of Spindle Per Ft 12.7mm,
Depth Of Taper 76.2mm,
Diameter Of Thru Hole 33.337mm,
Floor Space Required 940x1067mm,
Machine Net Weight 863.6 kGs.
Equipped with:
Standard 6-Series "Split-Head" Machine
Standard Two-Speed, 2-HP/1-HP, 440 Volt, 3-Phase,
50/60 Cycle, 1800/3600 RPM Drive Motor w/Pulleys
& Belts
Two-Speed Drum Switch
Forward/Reverse Spindle Rotation
Manual Braking System For Load Simulation Spring Chucking Mechanism (Both Spindles)
w/Draw-Rods & Nuts
Standard Bore Spindle 1-51/64" Diameter Full Complement Of Electrics (Motors/Controls) Guards, Covers Operators Manual, Parts List.
51
ID
MA21769
Make
Gleason USA
Model
17A
YOM
Condition
Good Condition
Photo
See Photo
Maximum offset of gear spindle above
or below center of pinion spindle 88.9mm,
Maximum distance from center of gear spindle to nose of pinion spindle304.8mm,
Minimum distance from center of gear spindle to nose of pinion spindle 152.4mm,
Maximum distance from center of pinion spindle to nose of gear spindle 196.85mm,
Minimum distance from center of pinion spindle to nose of gear spindle 104.8mm,
Max diameter of gear with "zero" offset of gear spindle 508mm,
Machine dimensions (approx.)1500 x 1825 x 1500 mm,
Machine net weight 5300 Lbs.
Equipped With :
Hydraulic work chucking cylinders on pinion
and gear spindles, (less draw-in bar & nuts) 5-hp, 220/440V, 3-ph 60 cyc, 1670 rpm main drive motor
3/4 hp, 220/440V, 3-ph 60 cyc, 1745 rpm hyd motor Pre-set backlash control Brake spindle (3-29/32" bore dia. Large end) Adjustable drive pinion spindle (3-29/32" bore dia.
Large end) w/crank handle & graduated dial Load meter Guards, covers, handwheels Full complement of electrics, motors/controls) Operator's manual wiring diagram & parts list.
52
ID
MA21763
Make
Gleason USA
Model
116
YOM
1976
Condition
Good Condition
Photo
See Photo
Diametral Pitch (coarsest) 2 DP(12.7-module) Maximum full depth 25.4 mm Cone Distance,
maximum (30-degree Sprial Angle & 12"
Diameter Cutter 230 mm,
Shafts at 90-degrees,
Max pitch angle.. 84 deg 18',
Minimum pitch angle 5 degrees 42',
Extreme Ratio (shafts at 90-degrees) 10 to 1,
Minimum ratio for pinions to operate with "Formate" gears 2 to 1,
Maximum gear pitch diameter: (30-degree Spiral Angle)
10 to 1 ratio 460 mm,
2 to 1 ratio 406 mm,
1 to 1 ratio 324 mm,
Maximum face width (depending on cutter)78 mm,
Max./Min. Number of Teeth 175 to 5,
Work Spindle Taper Bore Dia.(large end)100 mm,
Taper (per ft.)39/64"(1:20),
Depth of Taper 150 mm,
Diameter of hole through spindle 78 mm,
Diameter of spindle nose 140 mm,
Cutter Diameters Utilized 150,190,230,305 mm,
Workhead maximum offset above center 114 mm,
Workhead maximum offset below center 114 mm,
Maximum distance from machine center to nose of spindle 343 mm,
Minimum distance from machine center to nose of spindle 63 mm,
Cutter speeds 20 to 115 rpm,
Feeds (seconds per tooth) 9 to 80 seconds,
Feed motor 5 HP 1800 rpm,
Hydraulic motor .75 HP 1800 rpm,
Coolant motor .5 HP 3600 rpm,
Floor space 1905 x 2896 mm,
Machine Net Weight 23,700 Lbs.(10,773 kGs).
53
ID
MA20946
Make
Gleason USA
Model
YOM
1976
Condition
Excellent
Photo
See Photo
Gleason No. : 26.
54
ID
MA20379
Make
Gleason USA
Model
No.28
YOM
Condition
Good Condition
Photo
See Photo
Cone distance- max 419 mm, Face width- max. 102 mm, Dia of taper hole at large end- 152 mm, Taper per foot- 19 mm, Depth of taper -152 mm, Diameter of hole through- 127 mm, Max. distance from machine center to nose of spindle- 597 mm, Min. 127 mm with change gears full set.
55
ID
MA19442
Make
Gleason USA
Model
608
YOM
1975
Condition
Good Condition
Photo
See Photo
Outside cone distance : max 250 mm, min 100 mm, max gear pitch dia 500 mm, cutter dia utilized 225-450 mm, root angle 60-80 deg, face width 75 mm, number of teeth 20-75 , Equipped with :Hydraulic Chuck
Change Gears
1 Cutter Body w/Blades
Rotating Screw-Type Chip Conveyor
Coolant Tank, Pump & Piping
56
ID
MA19441
Make
Gleason USA
Model
609
YOM
1975
Condition
Good Condition
Photo
See Photo
Outside cone distance : max 250 mm, min 100 mm, max gear pitch dia 500 mm, cutter dia utilized 225-450 mm, root angle 60-80 deg, face width 75 mm, number of teeth 20-75 , Equipped with :Hydraulic Chuck
Change Gears
1 Cutter Body w/Blades
Rotating Screw-Type Chip Conveyor
Coolant Tank, Pump & Piping
57
ID
MA19256
Make
Russian
Model
5A872
YOM
Condition
Good Condition
Photo
See Photo
Max pitch dia of gear ground 800 mm, max pitch cone distance 60 mm, max module of gear ground 16, max tooth helix of gear ground 60, max face width of gear ground 100 mm, max height of gear teeth ground 33, no of teeth ground min 4, max 100, pressure angle of gears ground 20 degree, grinding wheel width 115 mm, power 15.25 kW, dimensions 2650 x 2100 x 2000 mm, machine weight 12.5 tons .
Qty: 4 Nos.
58
ID
MA19250
Make
Russian
Model
5C280P
YOM
Condition
Excellent
Photo
See Photo
max workpiece dia 800 mm, max modul 14 mm, max taper distance 360 mm, spindle RPM 18-172/t-min , dimensions 3485 x 3430 x 2860 mm, weight 16395 kg.
59
ID
MA19157
Make
Russian
Model
5S280P
YOM
1983
Condition
Good Condition
Photo
See Photo
Diameter of work piece to 800mm
External circular module to 16mm
External height of cog to 36mm
Conical distance to 360mm
Width of ring gear to 125mm
Angle of pitch cone from 5 degree
Number of cogs of detail from 5 to 150
Cycle time from 7 sec.
Power of electric motor of main movement 7,5 kilowatt
Total power of electric motors 17 kilowatt
External dimensions 3485х3730х2860mm
Weight 16395kg
60
ID
MA19153
Make
Russian
Model
5C280P
YOM
1992
Condition
Good Condition
Photo
See Photo
max workpiece dia 800 mm, max modul 14 mm, max taper distance 360 mm, spindle RPM 18-172/t-min , dimensions 3485 x 3430 x 2860 mm, weight 16395 kg.
61
ID
MA19015
Make
Russian
Model
5C280P
YOM
1979
Condition
electricals incomplete
Photo
See Photo
max workpiece dia 800 mm, max modul 14 mm, max taper distance 360 mm, spindle RPM 18-172/t-min , dimensions 3485 x 3430 x 2860 mm, weight 16395 kg.Extra Gears not available.
62
ID
MA19014
Make
Russian
Model
5A284
YOM
1976
Condition
Good working condition
Photo
See Photo
Dia of workpiece 1600 mm, max. outer circular module 22 mm, max. tooth depth 60 mm, mean cone distance 150-170 mm, max. face width 250 mm, pitch cone angle 5-85 degree, max. hypoid offset +260/-230 mm, distance between workhead spindle face & machine center 400-1470 mm, max. radius between workhead spindle face & cradle centerline 640 mm, nominal dia of gear cutter heads 500/630/800/1000 mm, overall dimensions (LxWxH): 5600 x 5000 x 3200 mm, max. weight 40,000 kg, universal type machine with easy changing from roughing to finishing operations on demand (using traditional method of cutting), implementation of completing crown wheel (driven gear) cutting cycle to complete full finishing of gears in one setup, designed for generating & semi-generating gear production, drastically simplified setups when changing over to different job.
63
ID
MA18739
Make
Russian
Model
5C270P
YOM
1983
Condition
Good Condition
Photo
See Photo
Max. diameter of wheels: 500 mm, Max. normal module: 8 mm, Max. height of wheel tooth: 22 mm, Max. cone distance of gear wheels: 220 mm, Max. width of gear ring: 80 mm, Inclination angle of tooth: any, Number of wheel teeth: 5-150, Min. angle of dividing cone: 5, Stock angle: -max.: +90 -min.: +5, Distance of end face from the spindle to the center -max. (when stock adjusting angle is 5 degree): 450 mm -min. (when stock adjusting angle is 90 degree): 75 mm, Min. hypoid displacement: -upper: 80 mm -down: 80 mm, Stock spindle tape according to GOST 17547-72: 100 mm, Diameter of stocks spindle opening in distance from end face spindle 500mm: 80 mm, Max. axis displacement of stock from initial point -to cradle: 20 mm -from cradle: 70 mm, Table diversion to disabled position: 100 mm, Max. swing angle of the cradle: 60 degree, Nominal diameter of gear-cutting heads according to GOST 17547-72: 100, 125, 160, 200, 250, 320, 400, Rotational speed of tool spindle: 19-210rev/min, Dimension of the machine: 2940x2090x2050 mm, Hydrostations dimensions: 830x700x1600 mm, Control box dimension: 600x500x1735 mm, Weight of the machine: 9000 kg, Weight of hydrostation: 470 kg, Weight of control box: 170 kg, Voltage: 50Hz, 380V, 220V.
64
ID
MA18355
Make
WMW Modul
Model
ZFTKK500/3A
YOM
1991
Condition
Good Condition
Photo
See Photo
Max. dia. of gear
-with a transmission ratio of 1:10 540 mm
-with a transmission ratio of 1: 1 380 mm
Module range 1 - 16
Length of cone angle 270 mm
Width of tooth 78 mm
Max. depth of tooth 36 mm
Number of teeth 6 – 100
Taper setting angle of work-carrier -10 - +90 °
Pitch cone angle, max. 90 °
Inclination of cutter spindle 0 – 30 °
Axial offset of the work spindle +/- 80 mm
Cutting head dia. 6 - 12 "
Cutter spindle speeds 23 – 224 rpm
Feed range 0.8 - 5.6 °/sec
Deep feed range 0.5 – 6 mm/min
Total electrical load 16 kW - 380 V - 50 Hz
Weight, approx. 12,000 kg - 3 machines
65
ID
MA18295
Make
Russian
Model
5A284
YOM
1973
Condition
Good Condition
Photo
See Photo
Dia of workpiece 1600 mm, max. outer circular module 22 mm, max. tooth depth 60 mm, mean cone distance 150-170 mm, max. face width 250 mm, pitch cone angle 5-85 degree, max. hypoid offset +260/-230 mm, distance between workhead spindle face & machine center 400-1470 mm, max. radius between workhead spindle face & cradle centerline 640 mm, nominal dia of gear cutter heads 500/630/800/1000 mm, overall dimensions (LxWxH): 5600 x 5000 x 3200 mm, max. weight 40,000 kg, universal type machine with easy changing from roughing to finishing operations on demand (using traditional method of cutting), implementation of completing crown wheel (driven gear) cutting cycle to complete full finishing of gears in one setup, designed for generating & semi-generating gear production, drastically simplified setups when changing over to different job.
66
ID
MA17384
Make
Gleason USA
Model
502
YOM
Condition
Good Condition
Photo
See Photo
diameter gear 267 mm,,diameter pinion 152 mm, automatic backlash control, hydraulic clamping.
67
ID
MA17382
Make
Gleason USA
Model
606
YOM
Condition
Good Condition
Photo
See Photo
Description: Piece holding table motor 35 Nm X axis motor 12 Nm , X axis visualized on DRO. Net weight 6500 kg Lubrification oil tank capacity 100 Lt. Specification: Milling spindle speed 50 / 200 RPM Max. diam. Of piece 350 mm Milling spindle motor 9kw Oil tank capacity for hydraulic system 60 Lt, Qty:4 nos.
68
ID
MA17381
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Cone Distance (max) 30 deg. Spiral Angle & 304 mm Cutter 228mm, Extreme Ratio : 10:1, Gear Pitch Dia. (max) (30deg. Spiral Angle) 10-1 Ratio - 457mm, 2 - 1 Ratio – 406 mm, 1 - 1 Ratio – 4323 mm, Diametral Pitch (coarsest) 2 - 12.7 Mod, Full Depth (max) - 25.4mm, Face Width (max) -69.9mm, Number of Teeth 5 to 150 Diameter of Taper Hole at Large End - 99 mm, Taper Per Foot - 15 mm, Depth of Taper - 152 mm, Diameter of Hole Through Spindle – 78 mm, Diameter of Spindle Nose – 140 mm, Cutter Diameter : 127 mm, 152 mm, 191 mm, Offset Above Center, Max. -114 mm, Offset Below Center, Max. -114 mm, Distance from Machine Center to Nose of Spindle, Max. - 343 mm, Distance from Machine Center to Nose of Spindle, Min. – 64 mm, Cutter Speeds - 20 - 115rpm Feed (seconds per tooth) : 9 - 80 sec. Floor Space : 2565 mm x 1981 mm, Height : 1626 mm, Net Weight : 24,200 lbs, Shipping Weight (boxed for export) : 26,300 lbs, Size of Case : 3048 mm x 2769 mm x 1854 mm. With: Coolant Pump, Hydraulic Work Clamping, Chamfer Attachment, 1 Set Up of Gears. Qty:6 nos.
69
ID
MA17302
Make
Gleason USA
Model
116
YOM
Condition
Good Condition
Photo
See Photo
Cone Distance (max) 30 deg. Spiral Angle & 304 mm Cutter 228mm,
Extreme Ratio : 10:1,
Gear Pitch Dia. (max) (30deg. Spiral Angle) 10-1 Ratio - 457mm,
2 - 1 Ratio – 406 mm,
1 - 1 Ratio – 4323 mm,
Diametral Pitch (coarsest) 2 - 12.7 Mod,
Full Depth (max) - 25.4mm,
Face Width (max) -69.9mm,
Number of Teeth 5 to 150
Diameter of Taper Hole at Large End - 99 mm,
Taper Per Foot - 15 mm,
Depth of Taper - 152 mm,
Diameter of Hole Through Spindle – 78 mm,
Diameter of Spindle Nose – 140 mm,
Cutter Diameter : 127 mm, 152 mm, 191 mm,
Offset Above Center, Max. -114 mm,
Offset Below Center, Max. -114 mm,
Distance from Machine Center to Nose of Spindle, Max. - 343 mm,
Distance from Machine Center to Nose of Spindle, Min. – 64 mm,
Cutter Speeds - 20 - 115rpm
Feed (seconds per tooth) : 9 - 80 sec.
Floor Space : 2565 mm x 1981 mm,
Height : 1626 mm,
Net Weight : 24,200 lbs,
Shipping Weight (boxed for export) : 26,300 lbs,
Size of Case : 3048 mm x 2769 mm x 1854 mm.
With:
Coolant Pump,
Hydraulic Work Clamping,
Chamfer Attachment,
1 Set Up of Gears.
Qty: 2 Nos.
70
ID
MA17018
Make
Russian
Model
528S(528C)
YOM
1966
Condition
Good Condition
Photo
See Photo
Work piece diameter 800 mm, module 16.
71
ID
MA15859
Make
Russian
Model
5C280P
YOM
1979
Condition
Good Condition
Photo
See Photo
max workpiece dia 800 mm, max modul 14 mm, max taper distance 360 mm, spindle RPM 18-172/t-min , dimensions 3485 x 3430 x 2860 mm, weight 16395 kg.
72
ID
MA15198
Make
Russian
Model
5C270P
YOM
1982
Condition
Good Condition
Photo
See Photo
Max. diameter of wheels: 500 mm, Max. normal module: 8 mm, Max. height of wheel tooth: 22 mm, Max. cone distance of gear wheels: 220 mm, Max. width of gear ring: 80 mm, Inclination angle of tooth: any, Number of wheel teeth: 5-150, Min. angle of dividing cone: 5, Stock angle: -max.: +90 -min.: +5, Distance of end face from the spindle to the center -max. (when stock adjusting angle is 5 degree): 450 mm -min. (when stock adjusting angle is 90 degree): 75 mm, Min. hypoid displacement: -upper: 80 mm -down: 80 mm, Stock spindle tape according to GOST 17547-72: 100 mm, Diameter of stocks spindle opening in distance from end face spindle 500mm: 80 mm, Max. axis displacement of stock from initial point -to cradle: 20 mm -from cradle: 70 mm, Table diversion to disabled position: 100 mm, Max. swing angle of the cradle: 60 degree, Nominal diameter of gear-cutting heads according to GOST 17547-72: 100, 125, 160, 200, 250, 320, 400, Rotational speed of tool spindle: 19-210rev/min, Dimension of the machine: 2940x2090x2050 mm, Hydrostations dimensions: 830x700x1600 mm, Control box dimension: 600x500x1735 mm, Weight of the machine: 9000 kg, Weight of hydrostation: 470 kg, Weight of control box: 170 kg, Voltage: 50Hz, 380V, 220V.
73
ID
MA12524
Make
Russian
Model
5C270P
YOM
1980
Condition
Good working condition
Photo
See Photo
Max diameter of wheels: 500 mm
Max normal module: 8 mm
Max height of wheel tooth: 22 mm
Max cone distance of gear wheels: 220 mm
Max width of gear ring: 80 mm
Inclination angle of tooth: any
Number of wheel teeth: 5-150
Min. angle of dividing cone: 5
Stock angle
-max:+90
-min:+5
DIstance of end face from the spindle to the center
-max. (when stock adjusting angle is 5 degree):450 mm
-min. (when stock adjusting angle is 90 degree): 75 mm
Min.hypoid displacement
-Upper:80mm
-Down:80mm
Stock spindle tape according to GOST 17547-72: 100mm
Diameter of stocks spindle opening in distance from end face spindle 500mm: 80 mm
Max. axis displacement of stock from initial point
-to cradle:20 mm
-from cradle:70 mm
Table diversion to disabled position:100 mm
Max. swing angle of the cradle:60 degree
Weight of the machine: 9000 kg
Weight of the hydrostation:470 kg
Weight of the control box:170 kg
Voltage:50Hz,380V,220V
74
ID
MA12272
Make
Russian
Model
5C270P
YOM
1988
Condition
Complete
Photo
See Photo
gear dia 500 mm, max. module 8 mm, max. height of wheel tooth - 22 mm, max. cone distance of gear wheel 220 mm, max. width of gear ring 80 mm,
75
ID
MA11548
Make
Russian
Model
5C270P
YOM
1980s
Condition
Good Condition
Photo
See Photo
gear dia 500 mm, max. module 8 mm, max. height of wheel tooth - 22 mm, max. cone distance of gear wheel 220 mm, max. width of gear ring 80 mm,
76
ID
MA10573
Make
Chinese
Model
Y2280
YOM
Condition
Brand New
Photo
See Photo
Dia 800 mm, max. module of work 15, extreme ratio 10:1, max. face width 100 mm, no. of teeth 4-100 mm, distance from machine center to nose of work spindle 125-600 mm, vertical displacement of work spindle from machine center + 90 / -90, cutter speeds 10-142 RPM, feeds (seconds/ tooth) 12-300, cutter dia 150 – 450, root angle range 5 degree 30 – 84 degree, dia of taper hole at large end & taper of work spindle hole 153 / 1:20, power of main motor 11 kW, overall dimensions (lxwxh) 2600 x 2650 x 2385 mm, weight of machine 14 tons, Machine Description:
This machine is designed for roughing and finishing various spiral bevel gears, generated pinions, Formate gears and hypoid gears. It is suitable for batch, mass and small lot productions.
It employs a face-mill type cutter for cutting teeth with generating method. The tooth profile shape is produced by the generating process, in which a relative rolling motion takes place between the gear or pinion and the rotating cutter. When roughing gears or roughing and finishing Formate gears, the in-feed method by which the cutter is in feeded uniformly is adopted to raise the productivity.
A combined gear with external and internal teeth is adopted on the machine, thus, the special index device can be omitted. When cutting gears, it makes the workpiece be continuous index for distributing the cutting heat uniformly.
This machine provides a high working accuracy.
This machine provides a rigid construction and advanced cutting elements. The carbide cutting tool may be used on the machine for taking high speed and strong force cutting.
Hydraulic system is arranged for the clamping of workpiece, rapid withdraw of sliding base, rapid reversing of friction clutch and making count of counting device.
77
ID
MA10572
Make
Chinese
Model
YT2250
YOM
Condition
Brand New
Photo
See Photo
Dia 500 mm, max. module of work 10, extreme ratio 10:1, max face width 70 mm, no. of teeth 5-100, distance from machine center to nose of work spindle 70-350 mm, vertical displacement of work spindle from machine center +60/ -50, cutter speeds 25-162 RPM, feeds (Seconds/Tooth) 16-76, cutter dia 150-300 mm, root angle range 5 degree-90 degree mm, dia of taper hole at large end & taper of work spindle hole 100 – 1:20, power of main motor 4 kW, overall dimensions (LxWxH) 2200 x 1600 x 1600 mm, weight of machine 7 tons,
This is a semi-automatic machine designed for roughing and finishing spiral bevel and hypoid gears.
A modified roll mechanism can be equipped with this machine. Thus, the machine can be arranged for roughing and finishing gear set of generated pinion and Formate gear as well as large cone distance gear. It can also be used to develop the contact pattern of the gear.
The following two cutting methods can be applied to the machine:
---Generating method
When cutting teeth with this method, the tooth profile shape is produced by the generating precess, in which a relative rolling motion takes place between the gear or pinion and rotating cutter.
---In-feed method
In-feed method, which is similar to the ordinary infeed method, is used on this machine for roughing generated gear and roughing or finishing Formate gear in order to raise the productivity.
A combined gear with external and internal teeth is adopted on the machine, thus, special index mechanism can be omitted. When cutting gears, it makes the workpiece be continuous index for distributing the cutting heat uniformly and enhances the precision standard.
Cutters with diameter of 6″, 9″and 12″are used on the machine. Cutter specifications are standard.
Hydraulic and electric systems are available for clamping the workpiece, advancing and withdrawing the sliding base, keeping certain pressure among the parts of modified roll mechanism, reversing the friction clutch for working or idle travel, counting the tooth numbers which have been cut as well as stopping the machine automatically.
This machine cuts gear with higher accuracy. It is suitable to cut gear not only in mass production but also in small amount production.
78
ID
MA15
Make
Model
5C270P
YOM
Condition
Photo
See Photo
dia. 500mm, modul 8