Category : Gear Machines

Sub-Category : Gear Generator Spiral bevel

Total Machines Found : 19

Select | Machine Details
 
  1
IDMA37801
MakeGLEASON
Model102
YOM
ConditionGood Condition
PhotoSee Photo
Diametral pitch (coarsest) 16 DP 1.6 Mod
Diametral pitch (finest) Limited only by smallest practical cutter point width
Cone Distance 0” – 2 5/16” 0 – 59mm
Workhead angle -12 deg. To 90 deg
Extreme ratio Any practical ratio
Minimum ratio for non-generated spiral bevel gears 2.5 to 1
Minimum ratio for non-generated hypoid gears 3.5 to 1
Maximum gear pitch diameter (shafts at 90 degree)
Face width ( maximum) 7/14” 11mm
Number of teeth 5-200, except prime
WORK SPINDLE
Diameter of taper bore,large end 1 17/32”
Taper ½” /ft
Depth of taper 3”
Diameter of hole through spindle Ύ”
CUTTER DIAMETER 1.1”, 1.5”, 2”, 2.75” 3.5” 28mm, 38mm, 51mm,
70mm, 89mm
WORK HEAD SETTINGS
Maximum offset above centre 1” 29mm
Maximum offset below centre 1” 29mm
Max distance from machine centre to nose of spindle 5.0” 127mm
Min distance from machine centre to nose of spindle 1 Ό” 32m
Machines are equipped with the following:
1-set-up of change gears for one part
1-cam
1-set of manuals
Electrical Diagrams
Misc tooling
 
  2
IDMA37504
MakeGLEASON
Model102
YOM
ConditionGood Condition
PhotoSee Photo  |  See Video
Max dia 117(spiral)、
Max dia 95(Hypoid)、
Max module1.6、
Face width(maximum)11mm、
Workhead angle -12°~90°、
Number of teeth 5~200mm、
Main motor 3/4HPΧ 1800rpm(60cycle)、
machine weight 1757KG
 
  3
IDMI8496
MakeWMW
ModelZSTTK280*8
YOM
ConditionGood Condition
PhotoSee Photo
Maximum Working Dia : 280mm
Maximum Module : 8
Tool Width : 70mm
Stroke Per Minute : 60-300
Main Motor : 3.5 Kw
Machine Weight : 3500 Kgs.
 
  4
IDMA35927
MakeGleason USA
Model116
YOM
ConditionGood Condition
PhotoSee Photo
max cone distance 406 MM,
max module 7
max gear pitch diameter° 42`- 84°5 
coolant motor 1,5 kW
space required 2.000 x 3.000 mm
weight 10.750 kg
 
  5
IDMA35926
MakeGleason USA
Model116
YOM1998
ConditionGood Condition
PhotoSee Photo
max cone distance 406 MM,
max module 7
max gear pitch diameter° 42`- 84°5 
coolant motor 1,5 kW
space required 2.000 x 3.000 mm
weight 10.750 kg
 
  6
IDMA35847
MakeSaratov
Model5C270P
YOM
ConditionGood Condition
PhotoSee Photo
Max. gear wheel diameter, mm 500 Module, mm 8 Max. gear wheel tooth depth, mm 22 Max. gear wheels cone distance, mm 220 Max. gear ring width, mm 80 Inclination angle of tooth: any Number of wheel teeth 5.150 Min. angle of dividing cone (pitch), degrees 5 Stock angle, degrees 5.90 Distance between spindle and machine center, mm: - max. (stock angle 5 degrees) 450 - min. (stock angle 90 degree) 75 Max. hypoid movement, mm: - upwards 80 - downwards 80 Table diversion to edge, mm 100 Nominal diameter of gear - cutting heads, mm 100, 125, 160, 200, 250, 320, 400 Tools rotation speed range, rot/min 26.210 Total power required, kW 13,2 Voltage, V 380 Frequency, Hz 50 Main motor power, kW 4 Machine dimensions, mm 2885 x 2570 x 1995 Machine weight, kg 8750
 
  7
IDMA35733
MakeKLINGELNBERG
ModelC28P
YOM2003
ConditionGood Condition
PhotoSee Photo
Weight: 17 ton ca.
The machine is very well maintained and has huge amount of accessories.
 
  8
IDMA35710
MakeGleason USA
Model12B
YOM
ConditionGood Condition
PhotoSee Photo
Capacity
Longest cone distance.. 12"
Longest cone distance (1" face ).. 11 1/8"
Shortest cone distance.. 0
Maximum pitch angle (angular gears).. 105
Maximum Pitch angle. (shafts at 90 degrees). 84" 18"
Maximum Pitch angle.... 5" 42"
Extreme ratio.... 10/1
Largest pitch diameter... see table
Longest face.... 3 1/2"
Length of stroke.. 1/2" to 4 1/4"
Index range (number of teeth)... 10 to 200
Minimum number of teeth in miters (more teeth recommended for good design).. 12
Largest pitch.... 3 D.P

Spindles
Diameter of taper hole large end ... 3 29/32"
Taper per foot... 39/64"
Depth of taper... 6"
Diameter of hole 15 3/4" deep.. 3 1/4"
Spindle nose to center line.. 2 1/2" to 15"
Diameter of hole through.. 3 1/16"
Speed and feed
13 tool speed in strokes per minute.. 64 to 495
18 feeds from 7.7 second to 2 minutes 11 seconds per tooth.
Drive
main motor.. 3 H.P 1800 (or 1500) R.P.M
Pump motor.. 1 1/2 H.P 1200 (or 1000) R.P.M
 
  9
IDMA35709
MakeGleason USA
Model12F
YOM
ConditionGood Condition
PhotoSee Photo
Max working diameter 300 mm
Max module 8, Machine weight 4300 Kg.
 
  10
IDMA35708
MakeGleason USA
Model12B
YOM
ConditionGood Condition
PhotoSee Photo
Capacity
Longest cone distance.. 12"
Longest cone distance (1" face ).. 11 1/8"
Shortest cone distance.. 0
Maximum pitch angle (angular gears).. 105
Maximum Pitch angle. (shafts at 90 degrees). 84" 18"
Maximum Pitch angle.... 5" 42"
Extreme ratio.... 10/1
Largest pitch diameter... see table
Longest face.... 3 1/2"
Length of stroke.. 1/2" to 4 1/4"
Index range (number of teeth)... 10 to 200
Minimum number of teeth in miters (more teeth recommended for good design).. 12
Largest pitch.... 3 D.P

Spindles
Diameter of taper hole large end ... 3 29/32"
Taper per foot... 39/64"
Depth of taper... 6"
Diameter of hole 15 3/4" deep.. 3 1/4"
Spindle nose to center line.. 2 1/2" to 15"
Diameter of hole through.. 3 1/16"
Speed and feed
13 tool speed in strokes per minute.. 64 to 495
18 feeds from 7.7 second to 2 minutes 11 seconds per tooth.
 
  11
IDMA35686
MakeGleason USA
Model724
YOM
ConditionGood Condition
PhotoSee Photo
Angle range (max.): 55 ° Range angle (max.): 55 °
Angle range (min.): 15 ° Range angle (min.): 15 °
Step diameter:
Semi-automatic: 6 "(mm. 152)
Automatic:
chute to channel: 6" (mm. 152)
gear and pinion collector: 4 "(mm. 102) Pitch diameter:
Semi-automatic: 6" (mm. 152)
Automatic:
chute: 6 "(mm. 152)
gear and pinion hopper: 4" ( mm. 102)
Shank length (max.):
Caricatore spanatura altezza: 4” (mm. 102)
Ingranaggio e raccoglitore pignone: 1½” (mm. 38) Shank length (max.):
Loader stripping height: 4” (mm. 102)
Gear and pinion hopper: 1½” (mm. 38)
Profonditΰ (max.):
16” cutters: .450” (mm. 11.4)
21” cutters: .585” (mm. 14.8) Depth (max.):
16” cutters: .450” (mm. 11.4)
21” cutters: .585” (mm. 14.8)
Larghezza a sfacciare (max.):
16” cutters: 1” (mm. 25.4)
21” cutters: 1-1/8” (mm. 28) Face width at root (max.):
16” cutters: 1” (mm. 25.4)
21” cutters: 1-1/8” (mm. 28)
Index range: 8-50 Index range: 8-50
MANDRINO: WORK SPINDLE:
Diameter of the tapered hole at large end: 3-29 / 32 "(mm. 99) Diameter of tapered hole at large end: 3-29 / 32" (mm. 99)
Spindle connection: 39/64 "(mm. 15.4) Taper for foot: 39/64 "(mm. 15.4)
Depth of taper: 5/8" (mm. 15.8) Depth of taper: 5/8 "(mm. 15.8)
Spreader behind the spindle connection: 2Ό" x 3-1 / 16 "(mm. 57.2 x 77.9) Counterbore behind taper: 2Ό" x 3-1 / 16 "(mm. 57.2 x 77.9)
Spindle hole diameter: 7/8" (mm. 22.3) Diameter of hole through spindle: 7 / 8 "(mm. 22.3)
ADVANCES AND SPEEDS: FEEDS AND SPEEDS:
Cutting speed (feet per minute):
16" cutters: 105-160 ft / min. (32.3-48.8 M / min)
21 "cutters: 107-163 ft / min. (32.9-51.0 M / min) Cutter speeds (feet per minute):
16 "cutters: 105-160 ft / min. (32.3-48.8 M / min.)
21” cutters: 107-163 ft/min. (32.9-51.0 M/min)
Avanzamenti (secondi per dente):
16” cutters: 1.6-2.4
21” cutters: 2.0-3.1 Feeds (seconds per tooth):
16” cutters: 1.6-2.4
21” cutters: 2.0-3.1
ATTREZZATURA ELETTRICA ELECTRICAL EQUIPMENT
Motore principale:
60 Hz: 15 HP, 1800 rpm
50 Hz: 15 HP, 1500 rpm Main drive motor:
60 Hz: 15 HP, 1800 rpm
50 Hz: 15 HP, 1500 rpm
Motore idraulico:
60 Hz: 7½ HP, 1200 rpm
50 Hz: 7½ HP, 1500 rpm Hydraulic motor:
60 Hz: 7½ HP, 1200 rpm
50 Hz: 7½ HP, 1500 rpm
Taglio pompa olio (incorporato nel motore):
60 Hz: 2 HP, 3600 rpm
50 Hz: 2 HP, 3000 rpm Cutting oil pump (built-in motor):
60 Hz: 2 HP, 3600 rpm
50 Hz: 2 HP, 3000 rpm
Motore truciolo vite:
60 Hz: Ό HP, 1800 rpm
50 Hz: Ό HP, 1500 rpm Chip screw motor:
60 Hz: Ό HP, 1800 rpm
50 Hz: Ό HP, 1500 rpm
PESI E MISURE: MISCELLANEOUS:
Ingombro: 126” x 87” (mm. 3200x2210) Floor space: 126” x 87” (mm. 3200x2210)
Peso netto: 22.000 lbs. (kg. 9600) Net weight: 22,000 lbs. (kg. 9600)
 
  12
IDMA35373
MakeKLINGELNBERG
ModelS35
YOM1993
ConditionGood Condition
PhotoSee Photo  |  See Video
FEATURES:
10-AXIS CNC CONTROL
SUITED FOR MEDIUM & LARGE SPIRAL BEVEL & HYPOID GEARS
599 MM MAXIMUM WORKPIECE DIAMETER
DESIGNED HIGH DEPENDABILITY & PRECISION
CONTINUOUS & SINGLE INDEXING OPERATIONS
SPECIFICATIONS
MAXIMUM WORKPIECE DIAMETER : 599 MM
SMALLEST NORMAL MODULE : 3 MM
LARGEST NORMAL MODULE : 10 MM
MAX TOOTH WIDTH : 100 MM
SMALLEST TRANSMISSION RATIO : 1:1
LARGEST TRANSMISSION RATIO : 1:10
SPIRAL ANGLE (DEGREES) : 0-60
CUTTER HEAD SPINDLE:
OERLIKON SHORT TAPER 1:4 : 130 M
SPINDLE SPEEDS (INF. VAR.) : 30-350 MIN-1
SPINDLE TILT (DEGREES) : 0-35
ECCENTRICITY : 275 MM
CUTTER HEAD RADIUS : 88 MM -181 MM
WORKPIECE SPINDLE
OERLIKON OUTSIDE TAPER 1:4 : 225 MM
INSIDE TAPER NO. 39, 1:19,692 : 152 MM
MAX SPINDLE SPEED : 0-160 MIN-1
BORE :160 MM
AXIAL OFFSET:+/-60 MM
SWIVEL RANGE (DEGREES):-7 UP TO 90
FEEDS:
GENERATING FEED (INF. VAR.): 40 DEG./SECOND
EQUIPPED WITH:
SCHLEICHER (SIEMENS) 10-AXIS CNC W/ RS-232
279 MM MAGNETIC CHIP CONVEYOR
BOSCH DRIVES
CONTINUOUS & SINGLE INDEXING METHODS
AC MOTORS & CONTROLS
100 KVA TRANSFORMER
CHILLER
MIST COLLECTOR
MCLEAN AIR CONDITIONER UNIT
 
  13
IDMI7848
MakeOrelikon
ModelSpiromat L22
YOM
ConditionGood Condition
PhotoSee Photo
Gear Width 250 mm
Max Wheel Diameter 500 mm
CNC Control GE Fanuc Series 16-M
 
  14
IDMA34896
MakeSaratov
Model5S286P
YOM
ConditionGood Condition
PhotoSee Photo
Machining is carried out with two shaving cutters using the plunge-cut and run-in methods.
The largest diameter of the processed wheel, mm 800
The largest outer circumferential module, mm 20
The greatest average taper distance, mm 450
The greatest width of the gear rim, mm 150
The smallest pitch cone angle, degrees 5
Number of teeth of the product 5-150
Diameter of the conical bore of the product headstock spindle, mm 154
Distance from the butt end of the headstock spindle to the center of the semiautomatic device, mm 135-600
Type of shaping cutters 4
Frequency of double strokes of sliders, dv. stroke / min 34-166
Angular feed rate by rolling, deg / s 0.2-3
Power of the electric motor of the main movement, kW 7.5
Overall dimensions of a semiautomatic device with separately located units, mm, no more than 3615x2970x2375
Semiautomatic device weight, kg, no more than 18 500
 
  15
IDMA34642
MakeWMW
ModelZFTKK 500/10
YOM
ConditionGood Condition
PhotoSee Photo
There are 2 such machines available.
Change gears are not available.
Max diameter - 500mm
Modul - 10
Weight - 10000kg
 
  16
IDMA34639
MakeGleason USA
Model26
YOM1965
ConditionGood Condition
PhotoSee Photo
Spindle hole's cone diameter - 152mm
Gears' diameter - 840mm
Modul - up to 16.9
Dimensions - 3350x2560mm
Weight - 11800kg
 
  17
IDMA34270
MakeSaratov
ModelCT527
YOM1995
ConditionGood Condition
PhotoSee Photo
Dia 500, module 12
 
  18
IDMA34211
MakeWMW Modul
ModelZFRKK 500/3
YOM1989
ConditionGood Condition
PhotoSee Photo
Workpiece Dimensions:
Max. outer pitch cone length: 270 mm,
Max. work diameter: 240 mm,
Max. outer real module: 16 mm,
Max. tooth widh: 78 mm,
range of number of teeth: 25.70
max. depth of teeth: 35
Max. middle cone distance: 240 mm,
at Bm:250 deg
Machine setting ranges
Cone setting angle of the work piece column: 60.90 deg,
Workpiece spindle distance: 0.300 mm,
Work piece spindle location hole: taper meteric 100
Distance between the tool spindles: 415 mm,
Cutter head diameter; 6;71/2 9; 12 inch
Ratings
Speed range of the cutter spindle: 27 . 168 rpm,
Speed range of the broaching spindle: 8. 25.5 rpm
Plunging feed: 0.5 . 6 mm/s
Rapid movement for lifting motion: 20 mm/s
Motor outputs Type RPM kW
main motor MFC 132M1 2060 7.5
Hydraulic motor KMR a 90 L4 1500 2.2
Lubricating pump motor KMR 71 G4 1390 0.75
Chip conveyor motor 2700 0.18
Coolant pump motor KMR 71 G2 2800 1.1
Swivel drive motor KMR 90 L4 1420 2.2
Mass:
Net weight: about 12000 kgf
Machine Dimensions length Breadth Height
machine 3150 1900 1850
hydraulic tank 1225 700 1080
Coolant tank 1800 950 800
Electric cabinet 1000 800 2200
Accessories cabinet 1000 400 1010
(Separately mountable)
Connected load: 22 kVA
 
  19
IDMA34156
MakeSaratov
Model525
YOM1983
ConditionGood working condition
PhotoSee Photo
Machine accuracy class according to GOST 8-82 and GOST 659-78 N N
The largest circumferential module of the cut wheel, mm 10
The greatest length of the generatrix of the initial cone at a helix angle of 0 ° / 30 °, mm 180/260
Smallest generatrix length, mm 0
The largest pitch circle diameter of the cut wheels at a gear ratio of the cut pair of 10: 1 at a helix angle of 0 ° / 30 °, mm 500/360
The largest pitch circle diameter of the cut wheels at a gear ratio of the cut pair of 2: 1 at a helix angle of 0 ° / 30 °, mm 450/320
The largest pitch circle diameter of the cut wheels at a gear ratio of the cut pair of 1: 1 at a helix angle of 0 ° / 30 °, mm 350/250
Weight 7000kg.
quantity: 2 nos
top