VKengg.co.in

Category : Forging Equipment

Sub-Category : Hammer Forging Air Steam

Total Machines Found : 124

Select	| Machine Details
1	ID MA39294 Make Romanian Model CM1250 YOM Condition Good Condition Photo See Photo maximum energy of impact at maximum stroke - 3600kgm; ram weight - 1250kg; mode of operation – pneumatic; table size (front to back) - 700mm; stroke - 800mm; number of blows per minute – 110; working pressure - 5 - 7bar; max. weight of upper die - 400kg; die height - 220mm; ram (front to back) - 500mm; air consumption - 15m3 / min; anvil weight - 24 t; height of machine above floor - 3750mm; total machine's height - 4380mm; total weight - 35t;
2	ID MI11235 Make HUTA ZYGMUNT Model YOM Condition Good Condition Photo See Photo Capacity - 1 Ton Extra spare Ram 1 nos - 6.50 Lakhs Anti Vibration pad - 4.20 Lakhs
3	ID MA39179 Make TMP Voronezh Russian Model M213 YOM 1986 Condition Good Condition Photo See Photo  |  See Video CAPACITY: 3 TON weigh approximately : 80 tons
4	ID MA39094 Make Model YOM Condition Good Condition Photo See Photo Nominal weight of the impact parts: 5000kg Impact energy: 125kJ Impact frequency: 50 strokes per minute Working stroke of the woman: 1300mm Steam (air) pressure: 7–9kg/cm² Air flow: 19m³/min Dimensions (L × W × H): 3700mm × 2000mm × 8770mm Total hammer weight: 139618kg Chabot weight: 75000kg Weight of the lower deck: 22000kg Minimum die height without shaft: 400mm Clear distance between guides: 800mm Head length (perpendicular to the front of the hammer): 950mm Die holder length (perpendicular to the front of the hammer): 1180mm Nominal weight of upper mold: 500kg Maximum weight of upper mold: 1500kg Maximum allowed steam temperature: 200°C
5	ID MA39031 Make HUTA ZYGMUNT Model MPM3150B YOM Condition Good Condition Photo See Photo RATED STRENGTH: 3,600 Kgm STROKE: 800 mm
6	ID MA38918 Make Huta Zygmunt,Polish Model MPM10000 YOM 1975 Condition Good Condition Photo See Photo Capacity 5 ton.m Weight Totals 103 tons Remark Without anvil
7	ID MA38917 Make Huta Zygmunt,Polish Model MPM10000 YOM 1975 Condition Good Condition Photo See Photo Capacity 5 Ton.m Weight Total 103 tons Remark Anvil is cracked Available Spare Parts : Crown, Anvil(Cracked) , Side Columns (2 pieces), 1 set of bolts, Guides (8 pieces) are available
8	ID MA38825 Make HUTA ZYGMUNT Model MPM6300B YOM Condition Good Condition Photo See Photo Capacity:2.5 tons, Energy of blow: 7000 kg.m, Weight of falling ram: 2500 Kg, Max. tup stroke:850 mm, Guideway spacing:650 mm, Length of die steam in the up: 650 mm, Length of die steam in the cushion: 900 mm, Min.height of the die (without doveta): 300 mm, Max. weight of upper die: 800 Kg, Stroke rate: 100 spm, Steam or incoming air pressure:5-7 Kg/cm2, Average steam consumption:970 kg/h, Average air consumption:18 m3/mm, Height above the floor:4100 mm, Total height:5145 mm, Weight of anvil:475 tons, Total weight of the hammer:64 tons.
9	ID MI11067 Make HUTA ZYGMUNT Model MPM16000B YOM Condition Good Condition Photo See Photo Huta MPM 16000 B complete hammer line:- 1. Huta MPM 16000 B (Brand new imported piston installed in december 2024) 2. Compressor 250 KW IR , 110 Kw gadner denver , 75 KW gadner denver 3. Tank 26000 litres + 15000 litres + 15000 litres 4. IBH 800 Kw 2023 model (with 3 coil set 125 rcs , 160 rcs, 200 rcs ) 5. Transformer with inbuilt servo 1000 kva 6. Vcb panel Complete machines sold - as is where is condition and all dismantling and loading in scope of buyer. Pipeline, foundation materials, electric cables, panels , press , are not included. Upper Anvil in as broken condition is included. Upper Anvil is Broken And To Be Replace With New.
10	ID MI11019 Make Russian Model YOM Condition Good Condition Photo See Photo CAPACITY 10 TON
11	ID MA38586 Make Progresul ,Romania Model CM2500 YOM Condition Good Condition Photo See Photo Very good working condition, without crucks and other damages, still under power. Nominal forging energy: 7000 kgm /70 KJ/; Ram stroke: 850 mm; Number of strokes: 100; Dimensions: - Length 3 000 mm - Width 1 700 mm - Height 5 250 mm Total weight: 64 000 kg Anvil weight: 47 000 kg
12	ID MA38583 Make STANKO Model M2145 YOM Condition Good Condition Photo See Photo Impact energy, kJ 80 Nominal weight of falling parts, kg 3150 Distance between guides in the light, mm 710 Distance between guides in the light, mm 710 Main drive motor power kW 0.08 Machine dimensions Length Width Height (mm) 3820_1800_5240 Weight kg 88000 (anvil weight 63,000 kg)
13	ID MA38369 Make Russian Model 18KP YOM Condition Good Condition Photo See Photo CAPACITY -10 TON
14	ID MA38343 Make Russian Model M2145 YOM Condition Good Condition Photo See Photo Nominal weight of falling parts, kg 3150 Distance between guides in the light, mm 710 Machine dimensions Length Width Height (mm) 3820_1800_5240 Weight kg 88000
15	ID MA38342 Make Voronezh Model M1343 YOM Condition Good Condition Photo See Photo CAPACITY -2 TON IMPACT ENERGY, KJ 50 NOMINAL WEIGHT OF FALLING PARTS, KG 2000 MAX NUMBER OF BLOWS PER MINUTE 56 WORKING ZONE DAYLIGHT, MM 530 DISTANCE BETWEEN COLUMNS, MM 2360 DIE IMPRESSION SIZE, MM 530 x 300 STEAM PRESSURE, MPA 0,7-0,9 HAMMER DIMENSIONS, MM 4900 x 1930 HAMMER HEIGHT ABOVE FLOOR LEVEL, MM5000 HAMMER WEIGHT WITH ANVIL BLOCK, KG 50100 ANVIL BLOCK WEIGHT, KG 30000
16	ID MI10628 Make Otani Model NEW-MAX 150S YOM 1981 Condition Good Condition Photo See Photo Dropping Section weight : 2250 Kg, Normal Die Weight : 450 Kg (Maximum) Maximum Stroke : 950 mm, Guide Distance : 590 mm, Die Thickness : 350 mm, Ram Bottom Surface size : 570 w * 550 mm, Inlet Pipe Size : 100 (A) (4B), Exhaust Pipe Size : 125(A) (5B), Maximum Stamping Force : 6800 Kg-m, Required Air Compressor Capacity 110 Kw, Maximum Air Pressure : 7 Kg/cm2
17	ID MI10613 Make EUMUCO Model YOM Condition Good Condition Photo See Photo Capacity - 6.35 Ton
18	ID MI10600 Make HUTA ZYGMUNT Model YOM Condition Good Condition Photo See Photo Capacity - 750 kg Hydraulic Tank Compressor
19	ID MA38157 Make Russian Model 17KP YOM Condition Good Condition Photo See Photo Nominal Mass Of Drop Parts : 5000kg Impact Energy : 125kJ Maximum Number of Blows Per Minutes : 50 Maximum Ram Stroke : 1300mm Distance Clear Between Guides : 800mm Ram Front to Back Dimensions : 950mm Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons
20	ID MA38045 Make Progresul Braila,Romania Model CM1250 YOM Condition Good Condition Photo See Photo maximum energy of impact at maximum stroke - 3600kgm; ram weight - 1250kg; mode of operation – pneumatic; table size (front to back) - 700mm; stroke - 800mm; number of blows per minute – 110; working pressure - 5 - 7bar; max. weight of upper die - 400kg; die height - 220mm; ram (front to back) - 500mm; air consumption - 15m3 / min; anvil weight - 24 t; height of machine above floor - 3750mm; total machine's height - 4380mm; total weight - 35t;
21	ID MA37931 Make Progresul ,Romania Model CM 2500 YOM Condition Good Condition Photo See Photo Very good working condition, without crucks and other damages, still under power. Nominal forging energy: 7000 kgm /70 KJ/; Ram stroke: 850 mm; Number of strokes: 100; Dimensions: - Length 3 000 mm - Width 1 700 mm - Height 5 250 mm Total weight: 64 000 kg Anvil weight: 47 000 kg
22	ID MA37930 Make CM Model CM1250 YOM Condition Good Condition Photo See Photo Very good working condition, without crucks and other damages, still under power. Nominal forging energy: 3600 kgm /36 KJ/; Ram stroke: 800 mm; Number of strokes: 110; Dimensions: - Length 2 600 mm - Width 1 300 mm - Height 4 300 mm Total weight: 35 000 kg Anvil weight: 24 000 kg
23	ID MA37686 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
24	ID MA37661 Make Russian Model 18KP YOM 1985 Condition Good Condition Photo See Photo  |  See Video Capacity - 10 Ton nominal mass of drop parts without upper instr.:9 tons, effective working kinetic energy after blow 25000 kg mtr., max. working ram stroke 1400 mm, max no of blows 30/min , distance between slides 1000 mm, shut height 775 mm , ram size front to back 1200 mm , bolster size front to back 1200 mm , air pressure 7-9 MPA , height of instruments 450 min.,die-holder front to back dimensions: 1400 mm,height above floor level: 7270 mm, hammer dimensions 4400 x 10420x2700 mm,mass (less anvil block): 75 ton, weight 205 tons.
25	ID MA37660 Make Russian Model M2152 YOM 1984 Condition Good Condition Photo See Photo Capacity: 16 tons, Nominal mass of drop parts: 16000 kg, Impact energy: 400 KJ, Ram stroke: 1500 mm, Ram stroke per minute: 20, Distance clear between guides: 1180 mm, Ram dimensions f-t-back: 1500 mm, Die holder dimensions f-t-back: 1600 mm, Bottom die impression to floor distance: 500 mm, Steam/air pressure: 0.7-0.9 MPa, Overall dimensions: 4500×2450×7920 mm, Mass of anvil block: 325 tons, Total weight of hammer: 425 tons.
26	ID MI9981 Make CM Model CM1250 YOM Condition Good Condition Photo See Photo Maximum energy of impact at maximum stroke: 3600kg Maximum working stroke of Ram: 800mm Number of blows per minute: 110 Nominal Working pressure bar: 5-7 Overall dimensions LxWxH: 2600x1300x4390 mm Weight: 35000kg Price Are Negotiable
27	ID MA37279 Make Huta Model CM3150 YOM Condition Good Condition Photo See Photo Maximum energy of impact at maximum stroke: 10000 kg Ram weight: 3150 kg Mode of operation: pneumatic Stroke: 900 mm Number of blows per minute: 90 Working pressure: 5 - 7 bar Weight: 105.000kg
28	ID MI9748 Make HUTA ZYGMUNT Model MPM2000A YOM 1981 Condition Good Condition Photo See Photo Energy of blow: 7 000 kgm Ram weight: 2 380 kg. Max. ram stroke: 950 mm Number of strokes per minute: 100 Total weight: 62.5 ton Anvil weight: 45 ton Perfect working condition without crucks and other damages still under power
29	ID MA37269 Make Russian Model M212 YOM Condition Good Condition Photo See Photo Impact energy, kJ 50 Nominal mass of falling parts, kg 2000 Number of strokes, 1/min: 60 total weight 58 tons, chabot weight 40 tons, Double-action steam-air forging hammer of arched type. M212 Designed for the production of forgings using hot die forging from ferrous, non-ferrous metals and alloys in hammer dies
30	ID MA37268 Make Russian Model M2145 YOM Condition Good Condition Photo See Photo Impact energy, kJ: 80 Nominal mass of goods of falling parts, kg: 3150 Number of strokes, 1/min: 56 Total weight 88 tons, chabot weight 63 tons Double-action steam-air stamping hammer M2145 Designed for the production of forgings of goods using hot die forging from ferrous, non-ferrous metals and alloys in hammer dies APPROX USD 220000 CIF INDIA, QUOTED PRICE IS IN RUSSIAN ROUBLE.
31	ID MI9321 Make Beche Model YOM Condition Good Condition Photo See Photo Capacity: 2 Tons
32	ID MA36814 Make HUTA ZYGMUNT Model MPM1600B YOM 1974 Condition Good Condition Photo See Photo Energy of blow: 1840 kg/m Maxi tup stroke: 750 mm Guideway spacing: 450mm Length of die seat in the tup: 400 mm Length of die seat in the die holder: 600 mm Min height of the die: 180 mm Max weight of upper die: 200 kg Min height of die above floor: 800 mm Stroking rate: 120 str/min Steam of incoming air pressure: 5 - 7 atm Average steam consumption: 380 kg/h Average air consumption: 7m3 /mn Height of hammer above floor: 3440mm Total Height of hammer: 3850 mm Weight of anvil without die holder: 12,5T Weight of hammer with anvil: 18,5T
33	ID MA36692 Make Huta Zigmunt License Model MPK2000 YOM Condition Good Condition Photo See Photo Energy of blow: 7 000 kgm Ram weight: 2 380 kg. Maximal ram stroke: 1 000 mm Total weight: circa 60 ton.
34	ID MA36656 Make Voronezh Model M1343A YOM 1980 Condition Good Condition Photo See Photo CAPACITY -2 TON IMPACT ENERGY, KJ 50 NOMINAL WEIGHT OF FALLING PARTS, KG 2000 MAX NUMBER OF BLOWS PER MINUTE 56 WORKING ZONE DAYLIGHT, MM 530 DISTANCE BETWEEN COLUMNS, MM 2360 DIE IMPRESSION SIZE, MM 530 x 300 STEAM PRESSURE, MPA 0,7-0,9 HAMMER DIMENSIONS, MM 4900 x 1930 HAMMER HEIGHT ABOVE FLOOR LEVEL, MM5000 HAMMER WEIGHT WITH ANVIL BLOCK, KG 50100 ANVIL BLOCK WEIGHT, KG 30000
35	ID MA36640 Make HUTA ZYGMUNT Model MPM1600B YOM Condition Good Condition Photo See Photo 1) Hammer Stroke rate 110 spm Total height 4380 mm Energy of blow 3600 kgm Max. tup stroke 800 mm Weight of anvil 24 tons Guideway spacing 550 mm Weight of falling ram 1250 Kg Height above the floor 3750 mm Average air consumption 12 m3/mm Max. weight of upper die 400 Kg Average steam consumption 650 kg/h Total weight of the hammer 35 tons. Length of die steam in the tup 500 mm Steam or incoming air pressure 5-7 Kg/cm2 Length of die steam in the cushion 700 mm Min.height of the die (without doveta) 220 mm 2) Hammer (A0692) Energy of blow 1840kg/m Max. tup stroke 750mm Guideway spacing 450mm Length of die seat in the tup 400mm Length of die seal in the die holder 600mm Min. height of the die 180mm Max. weight of upper die 200kg Min. height of die above floor 800mm Number of blows per minute 120 Steam of incoming air pressure 5-7 atm Average steam consumption 380 kg/h Average air consumption 7m2/min Height of hammer above floor 3440mm Total height of hammer 3850mm Weight of anvil without die holder 12.5T Weight of hammer with anvil 18.5T
36	ID MI8986 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo 750Kg
37	ID MA36534 Make Nittan ,Japan Model ADH-60-I YOM Condition Good Condition Photo See Photo Capacity - 6 Ton Standard dropping section weight(upper mold not included) (kg) 6200 Standard upper section weight(Nominal value) (kg) 1800 Stroke(mm)1300 Cylinder diameter: 580 mm Piston diameter: 210 mm Impact energy: 22415 kg.m Distance clear between guides: 795 mm Lower ram surface 795 W x 1006L mm Upper sow block surface 880 W x 1200L mm Inlet Pipe Size : 125A (5B) Exhaust Pipe Size : 200A (8B) Required Air Compressor Capacity ;535 Kw Maximum Air Pressure : 7 Kg/cm2
38	ID MA36410 Make Russian Model 18KP YOM Condition Good Condition Photo See Photo Capacity - 10 Ton nominal mass of drop parts without upper instr.:9 tons, effective working kinetic energy after blow 25000 kg mtr., max. working ram stroke 1400 mm, max no of blows 30/min , distance between slides 1000 mm, shut height 775 mm , ram size front to back 1200 mm , bolster size front to back 1200 mm , air pressure 7-9 MPA , height of instruments 450 min.,die-holder front to back dimensions: 1400 mm,height above floor level: 7270 mm, hammer dimensions 4400 x 10420x2700 mm,mass (less anvil block): 75 ton, weight 205 tons.
39	ID MA36374 Make Huta Zygmunt,Polish Model MPM1600B YOM Condition Good Condition Photo See Photo full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
40	ID MA36373 Make Huta Zygmunt,Polish Model MPM6300B YOM Condition Good Condition Photo See Photo Capacity:2.5 tons, Energy of blow: 7000 kg.m, Weight of falling ram: 2500 Kg, Max. tup stroke:850 mm, Guideway spacing:650 mm, Length of die steam in the up: 650 mm, Length of die steam in the cushion: 900 mm, Min.height of the die (without doveta): 300 mm, Max. weight of upper die: 800 Kg, Stroke rate: 100 spm, Steam or incoming air pressure:5-7 Kg/cm2, Average steam consumption:970 kg/h, Average air consumption:18 m3/mm, Height above the floor:4100 mm, Total height:5145 mm, Weight of anvil:475 tons, Total weight of the hammer:64 tons. Spare Ram
41	ID MA36365 Make Russian Model M212 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts: 2000 kg Impact energy: 50 kJ Max. number of blows per minute: 70 Max. ram stroke: 1200 mm Distance clear between guides: 600 mm Ram front-to-back dimensions: 670 mm Die-holder front-to-back dimensions: 900 mm Bottom die impression-to-floor distance: 840 mm Minimum die holder-to-ram distance: 260 mm Steam (air) pressure: -Inlet: 6-8 Mpa -Exhaust: 0,2-0,5 Mpa Overall dimension: 2950x1660 mm Height above floor level: 5310 mm Mass (less anvil block): 18,31 tons Mass of anvil block: 40 tons
42	ID MA36352 Make Kramatorsk Model M2147 YOM 1980 Condition Good Condition Photo See Photo Nominal weight of falling parts: 5000 kg Blow energy: 125 kJ Number of blows per min: 50 Max course of the hammer block: 1300 mm Min height of tools without shanks: 400 mm Distance between columns: 800 mm Length of the hammer block (at direction, Perpendicular to hammer front): 950 mm Length of the die holder (at direction, Perpendicular to hammer front): 1180 mm Total weight: 139 ton
43	ID MA35492 Make Russian Model M2150 YOM Condition Good Condition Photo See Photo Nominal weight of falling parts including 1,000 kg upper die kg:10,000 Effective blow energy for continuous full blows: kJ 260 Maximum ram working stroke: mm 1,400 Minimum die height without dovetails: mm 450 Distance between ram guides in daylight: mm 1,000 Ram length front-back: mm 1,180 Sow block length front-back: mm 1,320 Air pressure Bar: 7…9 Maximum weight of upper die: kg 3,000 That includes: - milling the anvil with the portable mill; - retrofitting of the ram and sowblock; - retrofitting of all wedges and plates; - repairing the main cylinder.
44	ID MA35443 Make TMP Voronezh Russian Model MA417 YOM Condition Good Condition Photo See Photo Nominal weight of the falling parts – 750 kg. Max. number of blows per minute – 105. Kinetic energy – 1900 kg. Distance from an axis of the slider up to bed – 750 mm. Cylinder diameter – 600 mm. Diameter of the plunger – 630 mm. Max. headstock travel – 835 mm. Dimensions: -Left-to-right – 3940 mm; -Front-to-back – 1430 mm. Height above floor level – 3260 mm. Weight – with an anvil-block – 25600 kg.
45	ID MA35142 Make Huta Zygmunt,Polish Model MPM2000 YOM Condition Good Condition Photo See Photo Weight of falling part: 2480 kg Stroke length: 950 mm distance between guides: 600 mm Max weight of upper stamp: 800 kg Height of stamp above the floor: 780 mm Blow energy: 7000 kgm Max. blows per minute: 100 Air pressure: 6-8 kg / cm2 Cylinder dia: 540 mm Total weight: 62,5 tons
46	ID MA34959 Make Banning Model GOA8000 YOM Condition Good Condition Photo See Photo Blow energy: 10.000 mkg, Ram stroke: 740 mm, Number of strokes: 105 min^-1 Die height: 360-580 mm, Ram weight: 4500 kg, Ram (front to back): 800 mm, Daylight: 850 mm, Distance between the guidelines: 800mm, Anvil weight: 85.400 kg, Dimensions of anvil: 3000 x 1850 mm, Dimensions: 5500 x 3000 x 1500 mm (LxB) height of machine above floor: 470 mm, Total weight: 72 ton, Mode of operation: Pneumatisch
47	ID MA34877 Make Saito Model YOM Condition Good Condition Photo See Photo  |  See Video Nominal weight of dropping parts(kg) 5500 Stroke (mm) 1250 Cylinder diameter (mm) 570 Piston rod diameter (mm) 200 Steam Pipe size (mm) 192 Exhaust Pipe size (mm) 218 Maximum working pressure (/cm2) 7 Between Guides (mm) 840 Ram dimensions front to back (mm) 850 Bottom the impression to floor distance (mm) 1100 Floor space (mm x mm) 4200 x 2600
48	ID MA34875 Make Eumuco,Germany Model YOM Condition Good Condition Photo See Photo Capacity: 6.3 ton, Weight is ab 100 ton (ab.60 = 40) Total weight of the hammer is ab.150 ton
49	ID MA34834 Make Eumuco,Germany Model YOM 1982 Condition Good Condition Photo See Photo Impact energy, kJ 80 Falling part weight 3150kg Number of strokes per minute 56 Distance between posts 2800mm Working area height 630mm Striker mirror size 600x340mm Steam temperature maximum 200С Maximum forging weight 820kg Hammer weight 72700kg Shabot weight 47200kg Width 5000mm Depth 2490mm Height above floor level 5500mm
50	ID MA34447 Make TMP Voronezh Russian Model M213 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts:3150 kg Rated striking energy:80 kJ Max. no. of blows/min.:56 Ram stroke:1250 mm Uprights distance:710 mm Ram dimensions:750 mm Die holder:1000 mm Min. die holder to ram distance:340 mm Steam/air pressure:0.7 — 0.9 MPa Dimensions:3820 x 1800 x 5240 mm Mass (less anvil block):25 tons Mass of anvil block:63 tons
51	ID MA34439 Make Stanko-Russia Model M415A YOM 1968 Condition Good Condition Photo See Photo Nominal weight of the falling parts: 400 kg Max. number of blows per minute: 130 Kinetic energy: 950 kg Distance from an axis of the slider up to bed: 520 mm Cylinder diameter: 480 mm Max. headstock travel: 530 mm Dimensions: -Left-to-right: 3105 mm -Front-to-back: 1270 mm Height above floor level: 2720 mm Weight: -With an anvil-block: 13500 kg -Without an anvil-block: 8700 kg
52	ID MA34425 Make TMP Voronezh Russian Model MA417 YOM Condition Good Condition Photo See Photo Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg
53	ID MA34361 Make Eumuco,Germany Model YOM Condition excellent working condition Photo See Photo 1 TON
54	ID MA33793 Make Huta Zygmunt,Polish Model MPM16000B YOM Condition Good Condition Photo See Photo CAPACITY:17.500 kgm MAX. STROKE:1.000 mm STROKES:80 n°/min MIN. DIE THICKNESS:400 mm LENGHT OF DIE SEAT IN THE RAM:900 mm LENGHT OF DIE SEAT IN THE DIE HOLDER:1.250 mm CYLINDER BORE:850 mm
55	ID MI7325 Make Huta Zygmunt,Polish Model 6300A YOM Condition Good Condition Photo See Photo capcity; 2 ton Height of the hammer above floor: 4100 mm, Weight of falling part (without die): 2490 Kg, Weight of anvil block without die holder: 47.5 ton, Height of hammer above floor: 4100 mm, Guide way spacing: 600 mm, Length of die seat in tup: 650 mm, Length of seat in the die holder: 900 mm, Max. tup stroke: 850 mm.
56	ID MA33556 Make Nittan ,Japan Model YOM Condition Photo See Photo 1.5 tons
57	ID MA33389 Make Otani Model YOM Condition Good Condition Photo See Photo Capacity: 1350 kgs Table: 530 x 550 mm
58	ID MA33276 Make Kramatorsk Model MA2147 YOM 1983 Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons
59	ID MA33268 Make TMP Voronezh Russian Model M213 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts - 3150 kg Rated striking energy 80 KJ Max. no. of blows/min. 56 Ram stroke 1250 mm Uprights distance 710 mm Ram dimensions 750 mm Fzmiwtkb Die holder 1000 mm Min. die holder to ram distance 340 mm Steam/air pressure 0.7-0.9 MPa Mass (less anvil block) 25 tons Mass of anvil block 63 tons (one piece)
60	ID MI7234 Make Model YOM 1995 Condition Good Condition Photo See Photo 1) Hammer forging air steam Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overall dimensions: Floor space : 3700 x 2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons With Trimming press: Capacity: 500 ton,
61	ID MA32946 Make Russian Model 17KP YOM Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
62	ID MA32917 Make Erie Model YOM Condition Good Condition Photo See Photo Rate size pounds: 12000 lb, Cylinder bore inches: 22 inch, Stroke inches: 50 inch Ram to sow block inches min: 20 inch Between guides inches: 30 inch Ram front back inches: 36 inch Front back: 71 inch left right: 140 inch height above floor ft & in: 1-0 Head room to drop in rod ft & in: 31-7
63	ID MA32851 Make EUMUCO Model YOM Condition Good Condition Photo See Photo 6000 Kg forging hammer
64	ID MA32848 Make Model YOM Condition Good Condition Photo See Photo 1) Offer #1510 Pneumatic air forging hammer model MA4136 Made in: Russia Manufacturer: Kalinin industrial association for the production of press-forging equipment Specification: Weight of the falling parts: 400 kg Strike energy: 11 kJ Strike frequency per min: 142 Flight: 30 mm Height of the working area: 530 mm Diameter of the working cylinder: 480 mm Diameter of the compressor cylinder: 480 mm Stroke of the compressor slide: 390 mm Max. headstock stroke: 640 mm Dimensions of the working surface: -Length: 560 mm -Width: 100 mm Optimal dimensions of the forging detail: 100 mm Power: 37 kW Overall dimensions: -Length: 3200 mm -Width: 1320 mm -Height: 2700 mm Height over the floor level: 2600 mm Weight: 13 tons 2) Offer #1511 Pneumatic air forging hammer model MA4132 Manufacturer: ASTRAXAN Factory Made in: Russia Specification: Weight of the falling parts: 160 kg Number of strokes per min: 196 Effective kinetic energy of falling part by stroke: 250 kg/m Distance from ram axis-to-frame: 350 mm Anvil dimensions: -Length: 190 mm -Width: 75 mm -Anvil height above the floor: 800 mm Diameter of working cylinder: 315 mm Diameter of compressor cylinder: 330 mm Stroke run: 390 mm Optimal stamping section of work-piece: -Square: 70 mm -Rounded: 80 mm Overall dimensions: -Length: 930 mm -Width: 1860 mm -Height above floor: 2160 mm Weight of the hammer with an anvil-block: 5290 kg 3)Offer #1713 Pneumatic air forging hammer model MA4132 Manufacturer: ASTRAXAN Factory Made in: Russia Specification: Weight of the falling parts: 160 kg Number of strokes per min: 196 Effective kinetic energy of falling part by stroke: 250 kg/m Distance from ram axis-to-frame: 350 mm Anvil dimensions: -Length: 190 mm -Width: 75 mm -Anvil height above the floor: 800 mm Diameter of working cylinder: 315 mm Diameter of compressor cylinder: 330 mm Stroke run: 390 mm Optimal stamping section of work-piece: -Square: 70 mm -Rounded: 80 mm Overall dimensions: -Length: 930 mm -Width: 1860 mm -Height above floor: 2160 mm Weight of the hammer with an anvil-block: 5290 kg
65	ID MA32815 Make Kramatorsk Model M2147 YOM 1980 Condition Good Condition Photo See Photo Nominal weight of falling parts: 5000 kg Blow energy: 125 kJ Number of blows per min: 50 Max course of the hammer block: 1300 mm Min height of tools without shanks: 400 mm Distance between columns: 800 mm Length of the hammer block (at direction, Perpendicular to hammer front): 950 mm Length of the die holder (at direction, Perpendicular to hammer front): 1180 mm Total weight: 139 ton
66	ID MI7147 Make Russian Model M2150 YOM Condition Good working condition Photo See Photo  |  See Video 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
67	ID MA32667 Make Tyazhpressmash Model M1343A YOM Condition Good Condition Photo See Photo Impact energy: 50 kJ Nominal mass of drop parts: 2000 kg Max. number of blows per minute: 56 Max. stroke of headstock: 1000 mm Distance between columns in daylight: 2360 mm Distance between guides in daylight: 550 mm Working zone height in daylight: 530 mm Bottom die impression-to-floor distance: 750 mm Die impression size (LxW): 530 x 300 mm Steam pressure: 0,7.0,9 MPa Compressed air pressure: 0,6.0,8 MPa Hammer dimensions (LxW): 4900 х 1930 mm Hammer height above floor level: 5000 mm Weight of the hammer without anvil block: 18100 kg Anvil block weight: 30000 kg Total weight: 48100 kg
68	ID MA32665 Make Russian Model M2145 YOM Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
69	ID MA32447 Make Otani Model YOM Condition Good Condition Photo See Photo Capacity: 1350 kgs Ram Back-Front: 550 mm
70	ID MA32445 Make Russian Model M2145 YOM 1990 Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
71	ID MA32215 Make Russian Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
72	ID MA31989 Make Russian Model MB2145 YOM Condition Good Condition Photo See Photo 3.15 tons, rated striking energy 80 KJ, max. no. of blows/min. 60, ram stroke 1250 mm, uprights distance 710 mm, ram dimensions 750 mm, die holder 1000 mm, min. Die holder to ram distance 340 mm, steam/air pressure 0.7-0.9 MPa, dimensions 3820x1800x5340 mm, total weight 88 tons
73	ID MA31987 Make Russian Model M212 YOM 1970 Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t.
74	ID MA31734 Make Russian Model MA2147 YOM Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons
75	ID MA31571 Make Huta Zygmunt,Polish Model MPM6300A YOM Condition Good Condition Photo See Photo Weight: 2500 Kg Blows Energy: 7000 Kgm Stroke Max Ram :33.4 inc Light :25.5 inc Height Min.: 11.8 inc Weight Max Inferior Die: 800 Kg SPM : 100 Steam Pression: 5-7 Kg/Cm Air Pression: 5-7 Kg/Cm Consumption Air Pression On Minute: 18 Mcub/Mn Roll Bore: 21.2 inc Chabotte Weight : 45,5 Ton Weight Hammer Ab. :70 Ton
76	ID MA31559 Make Russian Model MA2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
77	ID MA31471 Make Model M1343 YOM 1981 Condition Good Condition Photo See Photo Impact energy, kg 50 Nominal mass of the falling parts, kg 2000 Distance between guides in light, mm 2360 Distance between guides in light, mm 2360 Dimensions of the machine Length Width Height (mm) 4900_1930_5000 Weight kg 48700
78	ID MA31466 Make Russian Model M1345 YOM 1971 Condition Good Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons.
79	ID MA31459 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
80	ID MI7002 Make HUTA ZYGMUNT Model MPM1000 YOM Condition Photo See Photo 1000 MPM HUTA, Without Ram
81	ID MA31455 Make Model M2145 YOM 1986 Condition Good Condition Photo See Photo Model mv2145 Impact energy, kJ 80 Nominal mass of the falling parts, kg 3150 Distance between guides in light, mm 710 Distance between guides in light, mm 710 Dimensions of the machine Length Width Height (mm) 3400_1900_5450 Weight kg 88000
82	ID MA31454 Make Model M2147 YOM 1982 Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
83	ID MA31443 Make HUTA ZYGMUNT Model MPM10000 YOM 1889/1980 Condition Good Condition Photo See Photo Energy : 10.000 Kg Weight of the ram 3150 Kg Ram stroke 900 mm Max weight of upper die 1000 Kg Minimum total height of the die 260 mm Air pressure 5 – 7 bar Air consumption 22 cubic meter/min No of strokes/min 90 Distance between slides 750 mm Height above the floor 4430 mm Weight of the base 64.5 ton Total weight 96,6 ton Overall dimensions 3600 mm x2100 mm x 5930 mm
84	ID MA31400 Make Model M2143 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts, kg 2,000 Impact energy, kj . 50 Maximum number of blows per minute 70 Maximum ram stroke, mm 1,200 Distance clear between guides, mm 600 Ram front-to-back dimensions, mm 670 Die-holder front-to-back dimensions, mm 900 Bottom die impression-to-floor distance, mm 800 Minimum die holder-to-ram distance, . mm 260 Steam (air) pressure, MPa 0.6-0.8 Overall dimensions, mm: floor space 3,650 x x1,660 height above floor level 5,310 Mass (less anvil block), t, approx. 18 Mass of anvil block, t, approx. 40
85	ID MA31388 Make Russian Model M1345 YOM Condition Good Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons.
86	ID MA31387 Make Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
87	ID MA31248 Make Model 17KP YOM Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
88	ID MA31237 Make Model M2150 YOM 1980 Condition Good Condition Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
89	ID MA31186 Make Model M2150 YOM Condition Good Condition Photo See Photo N Case description Dimensions L,mm B,mm H,mm W,ton 1 cylinder unit ready assembled with under 4800 3000 1300 32,1 cylinder plate 2 Side Column 3650 2150 1900 21,1 3 Side Column 3650 2150 1900 21,1 4 anvil block (upper Part) 4400 2200 2650 108,1 5 anvil block (lower part) 4250 3000 1750 94,6 6 metal box wit fastening and small items 1230 870 800 2,5 6 tray with drawbar arms ready assembled with axis (2 pcs) 3850 1600 850 2,2 pipe range compensator (2 pcs) lubricating system tank 8 studs (8 pcs) 1250 850 400 0,8 9 tray with crosscut chock (3 pcs) lengthwise chock (2 pcs) 2100 800 400 1,8 metal fittings (7 pcs) 10 Anvil block bottom part 3800 2300 850 48 Total 332,2
90	ID MA31144 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
91	ID MA31129 Make Model MB2145 YOM 1986 Condition Good Condition Photo See Photo Impact energy, kJ 80 Nominal mass of the falling parts, kg 3150 Distance between guides in light, mm 710 Distance between guides in light, mm 710 Dimensions of the machine Length Width Height (mm) 3400_1900_5450 Weight kg 88000
92	ID MI6956 Make Model MPM1600B YOM Condition Good Condition Photo See Photo Ram stroke : 750 mm, Energy of full blow : 1840 kgm, Quantity of stroke : 120 u/min, Mass of anvil block : 12,5 t, Mass of hammer with anvil block : 21,9 t.
93	ID MA31085 Make Model M2143 YOM Condition Good Condition Photo See Photo Nominal mass of drop parts, kg : 2,000 Impact energy, kj . : 50 Maximum number of blows per : 70 minute Maximum ram stroke, mm : 1,200 Distance clear between guides, mm : 600 Ram front-to- back dimensions, mm . : 670 Die-holder front-to- back dimensions, : 900 mm Bottom die impression-to- floor : 800 distance, mm Minimum die holder-to- ram distance, : 260 . mm Steam (air) pressure, MPa : 0.6-0.8 Overall dimensions, mm: floor space 3,650 xx1,660 height above floor level : 5,310 Mass (less anvil block), t, approx. : 18 Mass of anvil block, t, approx. : 40
94	ID MA31066 Make Model MPM3150 YOM Condition Good Condition Photo See Photo Table size (front to back): 700 mm Stroke: 800 mm Strokes / min: 10 Working pressure: 5 - 7 atm Max. weight of upper die: 400 kg Die height: 220 mm Ram (front to back): 500 mm Air consumption: 15 m3 / min Anvil weight: 24 t Height of machine above floor: 3750 mm Total machine's height: 4380 mm Total weight: 35 t
95	ID MA31063 Make Model M2143 YOM Condition Good Condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
96	ID MA31032 Make HUTA ZYGMUNT Model MPM1600 YOM Condition Photo See Photo Energy of full blow: 1840 kgm Ram weight: 630 kg Ram stroke: 750 mm Spacing of guides: 430 mm Die cavity length: -In the ram: 400 mm -In the cushion: 600 mm Min. die height: 180 mm Max. load of upper die: 200 kg Height of die distribution over the floor: 800 mm Number of strokes per minute: 120 The intake air pressure: 0,5-0,7 MPa The intake vapor pressure: 0,5-0,7 MPa Average air consumption per minute: 7 m³ Average vapor consumption per hour: 380 kG Cylinder diameter: 320 mm Ram stem diameter: 240 mm Inlet pipe diameter: 80 mm Outlet pipe diameter: 80 mm Weight of anvil block: 12,5 tons Weight of hammer with anvil block: 12,5 tons
97	ID MA31031 Make HUTA ZYGMUNT Model MPM3150 YOM Condition Photo See Photo Table size (front to back): 700 mm Stroke: 800 mm Strokes / min: 10 Working pressure: 5 - 7 atm Max. weight of upper die: 400 kg Die height: 220 mm Ram (front to back): 500 mm Air consumption: 15 m3 / min Anvil weight: 24 t Height of machine above floor: 3750 mm Total machine's height: 4380 mm Total weight: 35 t
98	ID MA31029 Make Model M2143 YOM 1979 Condition excellent working condition Photo See Photo Capacity : 2 Ton Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
99	ID MA31023 Make HUTA ZYGMUNT Model MPM1600B YOM Condition Good Condition Photo See Photo - full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
100	ID MA31022 Make Huta Zygmunt,Polish Model MPM1600 YOM Condition Good Condition Photo See Photo - full impact energy: 1840 kGm - weight of the hammer (without die): 630 kg - total stroke of the hammer: 750 mm - spacing of guides: 430 mm - die slot length in the beater: 400 mm - length of matrix slot in the cushion: 600 mm - smallest height of dies (without tails): 180 mm - the highest weight of the upper die: 200 kg - die height above the floor: 800 mm - number of strokes per minute: 120 - intake air pressure: 0.5-0.7 MPa - intake vapor pressure: 0.5-0.7 MPa - average air consumption per minute: 7 m3 - average steam consumption per hour: 380 kG - cylinder diameter: 320 mm - diameter of the ram shaft: 240 mm - diameter of the intake pipe: 80 mm - outlet pipe diameter: 80 mm - mass of sabbot (without a pillow): 12,5 Ton - hammer mass with the saber: 21.9 tons
101	ID MA30988 Make Model M2143 YOM 1979 Condition Excellent Photo See Photo Capacity : 2 tons, Max ram stroke : 1200 mm Impact energy : 50 kJ Max no of blows per min : 70 Distance clear between guides : 600 mm Ram front-to-back dimensions : 670 mm Die holder front-to-back dimensions : 900 mm Bottom die impression-to-floor distance : 800 mm Min. die holder-to-ram distance : 260 mm Steam (air) pressure : 0.6 - 0.8 MPa Overall dimensions : 3650 x 1660 x 5310 mm Total weight : 50000 kg
102	ID MA30871 Make Huta Zigmunt License Model MPM3000A YOM Condition Good Condition Photo See Photo Energia del colpo / energy – kgm 10.000 Peso della mazza battente / weight of the ram – kg 3.570 Corsa max della mazza / max slide stroke– mm 1000 Luce fra le guide / light on the guide – mm 660 Peso max stampo superiore / weight max up.die – Kg 1.100 Numero colpi al min / stroke x min 90 Peso della chabotte senza porta stampi / weight chabotte without die holder – ton 70 Peso del maglio totale / total weight – ton 100
103	ID MA30866 Make HUTA ZYGMUNT Model MPM3150B YOM Condition Good Condition Photo See Photo  |  See Video ENERGY OF BLOW: 3600 kg.m STROKING RATE: 110 s.p.m. WEIGHT OF FALLING RAM: 1250 Kg STEAM OR INCOMING AIR PRESSURE:5-7 Kg/cm2 MAX. TUP STROKE :800 mm AVERAGE STEAM CONSUMPTION:650 Kg/h GUIDEWAY SPACING:550 mm AVERAGE AIR CONSUMPTION: 12 m3/mm LENGTH OF DIE SEAT IN THE TUP: 500 mm HEIGHT ABOVE THE FLOOR: 3750 mm LENGTH OF DIE SEAT IN THE CUSHION:700 mm TOTAL HEIGHT:4380 mm MIN. HEIGHT OF THE DIE (without dovetail):220 mm WEIGHT OF ANVIL: 24 T MAX. WEIGHT OF UPPER DIE: 400 Kg TOTAL WEIGHT OF THE HAMMER: 35 T
104	ID MA30805 Make M.I. KALININA Model M2145 YOM 1988 Condition Good Condition Photo See Photo Nominal mass of drop parts: 3150 kg Strike energy: 80 kJ Max number of blows per 1 min: 60 Max ram stroke: 1250 mm Distance clear between guides: 710 mm Ram front-to-back dimensions: 750 mm Die-holder front-to-back dimensions: 1000 mm Bottom die impression-to-floor distance: 800 mm Min die holder-to-ram distance: 340 mm Steam (air) pressure: 0.7-0.9 MPa Overall dimensions: -Floor space: 3820x1800 mm -Height above floor level: 5340 mm Weight without anvil: 25 ton Weight of anvil block: 63 ton Total weight of the hammer with anvil block: 88 ton
105	ID MA30640 Make Model YOM Condition Photo See Photo Air steam forging hammer type K05.501 Manufacturer: KALININ Factory Made in: Russia Strike energy: 40 kJ Nominal weight of the falling parts: 1600 kg Number of strokes per minute: 70 ± 10% Distance between guides in daylight: 520 mm Min. height of dies without shafts: 220 mm Max. height of dies without shafts: 460 mm Dimensions of die holder front-to-back: 620 mm Diameter of cylinder: 350 mm Diameter of rod: 125 mm Weight of upper die: -Min.: 85 kg -Max.: 200 kg Voltage: 360 V, 50 Hz Hammer dimensions: -Left-to-right: 3000 mm -Front-to-back: 1600 mm -Height over floor level: 4400 mm Hammer weight: 41000 kg
106	ID MA30633 Make Model MA2145 YOM Condition Photo See Photo 3.15 tons , striking energy 8000 KPM , rate of striking of hammer 50/min , working stroke of hammer 1250 mm , bearing distance between guidance 2700 mm , space of working area 630 mm , dimensions from upper anvil block till floor 750 mm , vapour pressure befor inlet 7-9 kp/cm2 , air pressure before inlet 6-8 kp/cm2 , outlet pressure of vapour and air 0,2-0,5 kp/cm2 , dia of piston rod 175 mm , dia of cylinder 460 mm , dimensions of hammer 5100 x 2490 x 5895 mm , anvil weight 47 tons , weight of hammer 75 tons
107	ID MA30551 Make Model M2143 YOM Condition Photo See Photo Capacity : 2 tons, Max ram stroke : 1200 mm, Impact energy : 50 kJ, Max no of blows per min : 70, Distance clear between guides : 600 mm, Ram front-to-back dimensions : 670 mm, Die holder front-to-back dimensions : 900 mm, Bottom die impression-to-floor distance : 800 mm, Min. die holder-to-ram distance : 260 mm, Steam (air) pressure : 0.6 - 0.8 MPa, Overall dimensions : 3650 x 1660 x 5310 mm, Total weight : 50000 kg
108	ID MA30550 Make Model M2147 YOM Condition Good Condition Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
109	ID MI6787 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity: 1 ton
110	ID MI6666 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity : 2 Ton, on foundation connected to pneumatic line and can take trial
111	ID MI6665 Make Huta Zygmunt,Polish Model YOM Condition Good Condition Photo See Photo Capacity : 1 Ton,
112	ID MA29639 Make Huta Zygmunt,Polish Model MPM3000A YOM Condition Good Condition Photo See Photo Weight of the Machine 3570 Light between the guides 660 Length of the joint in the club 750 Length of the joint in the mold holder 1050 Minimum height of the molds (dovetail not included) 350 Maximum weight of the upper mold 1100 Height of the meeting line of the molds from the ground 765
113	ID MA29638 Make Huta Zygmunt,Polish Model MPM16000B YOM 1979 Condition Excellent condition,under power Photo See Photo Weight of the Anvil 6300 kg Energy 17500 Kgm Light Among the gulde 850 L.Jogance of the incestro net • stamp 1250 Minimum Atterts de escapes (annuity queue not included 400 Weight max. of the stamp Supt.:lore 1600
114	ID MA29631 Make Russian Model M212 YOM Condition Good Condition Photo See Photo 2 tons, impact energy 50 kj, max. no. of blows 70 per minute, max. ram stroke 1200 mm, distance clear between guides 600 mm, ram front-to-back dimensions 670 mm, die-holder front-to-back dimensions 900 mm, bottom die impression-to-floor distance 800 mm, minimum die holder-to-ram distance 260 mm, steam (air) pressure, 0.6-0.8 MPa, overall dimensions: floor space 3650 x 1660 mm, height above floor level 5310 mm, mass (less anvil block) approx. 18 t, mass if anvil block approx. 40 t.
115	ID MA29436 Make Huta Zygmunt,Polish Model MPM6300B YOM Condition Good Condition Photo See Photo Energy of blow : 7000 kg/m, Weight of falling ram : 2500 kg, Max. tup stroke : 850 mm, Guideway spacing : 650 mm, Min. height of die : 300 mm, Max. weight of upper die : 800 kg, Stroking rate : 100 s.p.m, Hight over floor : 4100 mm, Total hight : 5.145 mm, Total weight of hammer : 64 tons, Weight of anvil : 47,5 tons
116	ID MA29269 Make Kramatorsk Model 17KP YOM 1984 Condition Good Condition Photo See Photo 5 tons , energy of striking 12500 kJ, rate of striking 50/min , working stroke of hammer 1300 mm , bearing distance between guidance 800 mm , ram dimensions , front 950 mm , die holder dimensions front 1180 mm , dimensions between ram and die holder 400 mm , vapour pressure (of compressed air) 0,7-0,9 Mpa , dimensions of hammer : in top view 3700 x 2000 mm , height above floor level 8770 mm , weight of hammer without anvil 40 tons , anvil weight 100 tons .
117	ID MA28751 Make Russian Model M2145 YOM 1981 Condition Good Condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
118	ID MA28720 Make Erie Model YOM 1972/1985 Condition Good working condition Photo See Photo Capacity: 8 ton, Hit energy: 208(20,8) kJ, Weight of falling parts: 9000 kg, Impact frequency:~55±5 min-1, The minimum die height:600-100 mm, Ram size from front to back: 1020 mm, Anvil block insert size from to back : 1450 mm, Steam (Air) manometric pressure,MPa: 0,8(8) kg/cm2, Diameter of cylinder: 609,6 mm, Ram diameter: 216 mm
119	ID MA28585 Make Russian Model MA2147 YOM 1980 Condition Excellent Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
120	ID MA28468 Make Russian Model MA2147 YOM Condition Excellent Photo See Photo 5 tons,impact energy 125 kj, ram stroke 1300 mm, no. of blows 50 per min., distance clear between guides 800 mm, ram front to back dimensions 950 mm, die holder front to back dimensions 1180 mm, bottom die impression to floor distance 700 mm, minimum die holder to ram distance 400 mm, steam (air) pressure 0.7-0.9 MPa, overall dimensions: 3700 x 2000 x 6470 mm, mass (less anvil block) approx. 40 tons, mass of anvil block approx. 99 tons
121	ID MA28363 Make Huta Zygmunt,Polish Model MPM25000 YOM Condition Excellent Photo See Photo Capacity : 8 tons, Stroke energy : 25000 kgm, Maximum stroke : 1100 mm, Light between guides : 850 mm, Stroke : 75 min, Ram Weight : 8060 mm, Shut height : 1400 mm, Die weight max : 2400 mm, Compressed Air : 5-7, Air consumption per hour : 2000 kg, Die of ram rod : 610 mm, Anvil block weight : 170 t. Total hammer weight : 225 t.
122	ID MA28306 Make Russian Model M2150 YOM 1970 Condition Good condition,under power Photo See Photo 10 tons , Weight of the ram 10000 Kg, Blow energy 26000 Kgm, Speed 30 stroke/minute, Stroke 1400 mm, Distance between guides 1000 mm, Ram surface 1180 x 1180 mm, Surface die support 1320 x 1320 mm, Overall dimensions 4400 x 2700 x 7238 mm, Weight of the base 200 ton, Total weight 284 tons.
123	ID MA28278 Make TMP Voronezh Russian Model M2145 YOM 1990 Condition Very good condition Photo See Photo Capacity : 3.15 tons, Ram stroke : 1250 mm, Rated striking energy : 80 KJ, Max. no. of blows/min. : 60, Uprights distance : 710 mm, Ram dimensions : 750 mm, Die holder : 1000 mm, Min. Die holder to ram distance : 340 mm, Steam/air pressure : 0.7-0.9 MPa, Dimensions : 3820 x 1800 x 5340 mm, Mass (less anvil block) : 25 tons, Mass of anvil block : 63 tons.
124	ID MA28111 Make Kramatorsk Model MA2147 YOM Condition Good Condition Photo See Photo Capacity : 5 ton, Nominal mass of drop parts : 5000 kg, Rated striking energy : 125 KJ, Max. no of blows/min : 50, Ram stroke : 1300 mm, Uprights distance : 800 mm, Ram dimensions front to back : 950 mm, Die holder dimensions front to back : 1180 mm, Bottom die impression to floor distance : 700 mm, Min.die holder to ram distance : 400 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions: Floor space : 3700x2000 mm, Height above floor level : 6470 mm, Mass (less anvil block) : 40 tons, Mass of anvil block : 99 tons, Quantity No. : 2.